Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Generac Power Systems TTS Series
Summary of Contents for Generac Power Systems TTS Series
- Page 1 TTS Series TMS-200 200A Manual Transfer Switch Owner's Manual Model 006301-0 120/240V, 1-phase Model 006303-0 120/208V, 3-phase Only qualified electricians or contractors should attempt installation! 120/240V, 3-phase This manual should remain with the unit.
-
Page 2: Table Of Contents
Table of Contents Safety Rules ................1 General Information ..............2 Read the following information carefully Introduction ................2 before attempting to install, operate or ser- Equipment Description ...............2 vice this equipment. Also read the instruc- 1.2.1 Manual Transfer Switch...........2 tions and information on tags, decals, and 1.2.2 Cam-Lock™... -
Page 3: Safety Rules
Safety Rules Throughout this publication, and on tags and decals affixed to the GENERAL HAZARDS generator, DANGER, WARNING, CAUTION and NOTE blocks are used to alert personnel to special instructions about a particular operation that may be hazardous if performed incorrectly or care- •... -
Page 4: General Information
General Information 1.1 INTRODUCTION This device is suitable for use as service equipment. Customer connections. Refer to the installation diagram for loca- This manual has been prepared especially for the purpose of tion and wire size capacity. All lugs are rated for copper or alumi- familiarizing personnel with the design, application, installation and num wire. -
Page 5: Utility Fail Relay
General Information 1.3 RATINGS — DATA LABEL 1.2.4 UTILITY FAIL RELAY A "dry-contact" signal is provided to annunciate when the Utility This TMS is rated 200 amp at 120/240 VAC single phase or, supply fails. 120/208 or 120/240 VAC three phase. A DATA LABEL is perma- nently affixed to the transfer switch subplate. -
Page 6: Installation
Installation 2.1 INTRODUCTION TO INSTALLATION 2.4 CONNECTING UTILITY AND LOAD LINES This equipment has been wired and tested at the factory. Installing the switch includes the following procedures: M ake sure to turn OFF the NORMAL • Unpacking the TMS. (UTILITY) power supply and unplug the •... -
Page 7: Generator Annunciator Connections
Operation 3.1 FUNCTIONAL TESTS AND Disconnect the Cam-Lok™ connectors in the following order; Blue – Line 3 (only used on 3-phase systems) ADJUSTMENTS Red – Line 2 Following transfer switch installation and interconnection, inspect Black – Line 1 the entire installation carefully. A competent, qualified electrician White –... -
Page 8: Installation Drawings
Installation Drawing Drawing No. 0J9908ID-A 508mm[20.00"] 228.6mm[9.00"] 228.6mm[9.00"] 76.21mm[3.00"] M8X25 PEM STUD 0E7508-T M8X25 PEM STUD 0E7508-T RECOMMENDED 508mm[20.00"] MOUNTING MOUNTING BRACKET 355mm[14"] HARDWARE INCLUDED 3/8" M8X25 PEM STUD 0E7508-S 11.1mm[0.44"] TYP. FRONT VIEW... - Page 9 Installation Drawing Drawing No. 0J9908ID-A WIRE SIZE 350MCM-#6 UTILITY GENERATOR 0H3797B-F 0H3797B-S 10-32X5/16 0F7807B-S SUPPLY SUPPLY 10-32X5/16 0F7807B-S WIRE SIZE 350MCM-#6 067989-T M8 WHIZ 067989-T M8 WHIZ 067989-T M8 WHIZ 067989-T M8 WHIZ 0 D 2 9 0 8 - S M 4 X 1 5 S T U D M4X15STUD-T 0D2908-T...
-
Page 10: Notes
Notes... - Page 11 Notes...
-
Page 12: Warranty
NOTE: ALL UNITS MUST HAVE A START-UP INSPECTION PERFORMED BY AN AUTHORIZED GENERAC DEALER. For a period of two (2) years of operation from the date of start up, Generac Power Systems, Inc. (Generac) will, at its option, repair or replace any part(s) which, upon examination, inspection, and testing by Generac or an Authorized/Certified Generac Dealer, or branch thereof, is found to be defective under normal use and service, in accor- dance with the warranty schedule set forth below.
Need help?
Do you have a question about the TTS Series and is the answer not in the manual?
Questions and answers