Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Beko HLV-800-3
Summary of Contents for Beko HLV-800-3
- Page 1 HLV-800-3 Instruction & Operations Manual Content...
-
Page 2: Table Of Contents
Chapter page Certificate of conformity Introduction Safety instructions Electrical connections Warranty Front panel operation Protection circuits Receive-Transmit switching Remote control Cooling technique Block diagram Adjustment of protection thresholds Control circuit schematic... -
Page 3: Certificate Of Conformity
EN 301 489-1 V1.6.1 (2005-09), EN 301 489-15 V1.2.1 (2002-08) EN 60950-1: 2006 All necessary test procedures have been successfully passed Manufacturer and authorized representative: BEKO-ELEKTRONIK Am Längenmoosgraben 1a D-85221 Dachau GERMANY This declaration has been accomplished under unique reponsability of the manufacturer... -
Page 4: Introduction
2. Introduction Congratulations on purchasing your new BEKO linear amplifier. You have purchased a quality product, individually built to the highest standards and one that will last you a lifetime. Please take a few minutes to read these instructions manual and then store it in a safe place for future reference. -
Page 5: Safety Instructions
3. Safety instructions Please be aware of the following before use: Caution! This device is generating high frequency energy with high power which is highly dangerous in case of improper connection and use. Mains connection is only allowed to sockets including a rules compliant PE connection. -
Page 6: Electrical Connections
4. Electrical connections In order to guarantee trouble free operation you should observe the following instructions: 1. The device is only permitted for operation with mains voltages of 180 – 260 Volts AC and frequencies between 50 - 60 Hz. Operation at 100 – 130 VAC 50/60 Hz is generally possible but with lowered specifications. -
Page 7: Warranty
5. Warranty Congratulations for purchasing a BEKO power amplifier. This solid state device uses the latest circuit design techniques and features high quality “Made in Germany” precision assembly. This unit meets the latest CE conformity and FCC rules. We grant a 2 years warranty including parts and labour beginning from the date of purchase. -
Page 8: Front Panel Operation
5. Front panel operation POWER After switching the “POWER”-switch the amplifier is turned on, which is indicated by the green “ON”-LED. It takes approx. 5 seconds until the internal supply voltage rises up to 50 VDC and releases PTT operation. The HLV-800 has an integrated pfc-controlled switched power supply with an efficiency of >... -
Page 9: Protection Circuits
RESET The HLV-800 operation is internally monitored by many highly efficient protection circuits. If any limit is exceeded the device shuts off. If any protection circuit is activated the red “PROTECTION”-LED illuminates as well as one of the three protection circuit LEDs “ANTENNA”, “OVERDRIVE”... -
Page 10: Receive-Transmit Switching
7. Transmit operation ATTENTION ! This device is for split line operation only. There is no output relay inside. Separate cables for TX and RX must be used. An external output relay can be used with the internal sequencer. SEE Chapter Remote control for more details. -
Page 11: Remote Control
9. REMOTE control This amplifier can also be remote controlled. RESET- , PREAMP- and PTT- function can easily be activated by an external switch wired to ground. Output power can be monitored. 100% of output power is equal to 10V DC on Pin 5. Remote control HLV--800 Shield 100% power level = 10V DC... -
Page 12: Cooling Technique
10. Cooling technique The integrated axial blowers are temperature controlled and provide sufficient cooling during long time operation at full output power with minimum noise level. During the TX period the airflow through the rf box is increased by higher speed of the cavity blower which is noticeable by a slight noise increase. -
Page 13: Block Diagram
11. Block diagram... -
Page 14: Adjustment Of Protection Thresholds
12. Adjustment of protection thresholds In some cases the default adjustments are too sensitive and need some slight correction. In the picture below all trimpots incl. their functions are shown. Turning the slots clockwise is equal to + or upward direction and verse vice. Readjustment should be done very carefully otherwise the effect of protection is cancelled.