Table of Contents
Related Manuals for North-Vision Tech Prince-100B
Summary of Contents for North-Vision Tech Prince-100B
- Page 1 Fingertip Pulse Oximeter North-vision Fingertip Pulse Oximeter Prince-100B User Manual Version: 2.1 Issued by: Sara Lo Date: 5/11/2020 Reviewed by: Albert Huang Date: 5/11/2020 Document No: UM-OX1-201107-01 North-Vision Tech. Inc. 2460...
- Page 2 Fingertip Pulse Oximeter Instructions to User Dear Users, Thank you very much for purchasing our product. Please read the manual very carefully before using this device. If you do not follow these instructions may cause measuring abnormality or damage to the oximeter. The manual is published in English and we have the right to explain the Manual.
- Page 3 Fingertip Pulse Oximeter Instructions for Safe Operations Check the device to make sure that there is no visible damage that may affect user’s safety or measurement performance with regard to sensors and clips. It is recommended that the device should be inspected minimally once a week.
- Page 4 Fingertip Pulse Oximeter Warnings An uncomfortable or painful feeling may appear if using the oximeter continuously on the same place for a long time, especially for poor microcirculation patients. It is recommended that the oximeter should not be applied to the same location for longer than 2 hours.
- Page 5 Fingertip Pulse Oximeter If the oximeter gets wet, please stop using it and do not resume operation until it is dry. When it is carried from a cold environment to a warm and humid environment, please do not use it immediately. DO NOT operate the button on the front panel with sharp materials.
-
Page 6: Table Of Contents
Fingertip Pulse Oximeter Table of Contents 1 Overview 1.1 Appearance 1.2 Name and Model 1.3 Feature List 1.4 Applications and Scope 1.5 Key of Symbols 2 Battery Installation 3 Quick Guide to Operation 4 Display Screen 5 Instructions For Operation 6 Technical Specifications 7 Accessories 8 Repair and Maintenance... -
Page 7: Overview
Fingertip Pulse Oximeter 1 Overview 1.1 Appearance Rubber Display Cushions Display Screen Figure 1 Front View Nameplate Battery Cover Hanging Hole Figure 2 Rear View - 1 -... -
Page 8: Name And Model
Fingertip Pulse Oximeter 1.2 Name and Model Name: Fingertip Pulse Oximeter Model: Prince-100B 1.3 Feature List Model Function Prince-100B Display screen OLED √ SpO2 √ √ √ Plethysmogram √ Auto on √ Auto off √ Alarm √ Low voltage indication √... -
Page 9: Applications And Scope
Fingertip Pulse Oximeter 1.4 Applications and Scope Fingertip Oximeter is intended for measuring the pulse rate and functional oxygen ) through the testee’s body saturation (SpO especially on finger. It is designed by using internal (build-in) sensor and applicable for spot-check during no motion and well perfusion condition and can be used in homes, hospitals and clinics. -
Page 10: Battery Installation
Fingertip Pulse Oximeter 2 Battery Installation Figure 3 Battery Installation 1 Refer to Figure 3, insert two AAA size batteries into the battery compartment properly. 2 Replace the cover. Please make sure that the batteries are correctly installed, or incorrect installation may cause the device not to work. -
Page 11: Quick Guide To Operation
Fingertip Pulse Oximeter 3 Quick Guide to Operation Step Operation Open the clip and put finger into the rubber cushions of the clip (make sure the finger is in the correct position), and then clip the finger. Wait 2 seconds, the oximeter will power on automatically and start to measure. -
Page 12: Instructions For Operation
Fingertip Pulse Oximeter 5 Instructions for Operation • The finger should be put in properly and correctly. • Do not shake the finger. Keep at ease during measurement. • Do not put wet finger directly into sensor. • Avoid placing the device on the same limb which is wrapped with a cuff for blood pressure measurement or during venous infusion. -
Page 13: Technical Specifications
Fingertip Pulse Oximeter orientation detection would be delayed. Please move the oximeter with a bit of force if you want to change the display direction(such as bend/extend your finger quickly), so an acceleration is provided to the orientation-sensor for quick sensing the orientation change. - Page 14 Fingertip Pulse Oximeter E. Preset alarm limits SpO2 alarm: Lower limit: 90% Pulse Rate alarm: Upper limit: 120bpm Lower limit: 50bpm F. Audible&visual alarm function When measuring, if SpO2 value or pulse rate value exceeds the preset alarm limit, the device will alarm automatically and the value which exceeds limit on the screen will flash.
- Page 15 Fingertip Pulse Oximeter J. Resistance to 50Hz /60Hz interference: SpO2 and PR are precise which have been tested by BIO-TEK pulse oximeter simulator. K. Dimensions: 66 mm (L) × 36 mm (W) × 33 mm (H) Net Weight: 60g (including batteries) L.
-
Page 16: Accessories
Fingertip Pulse Oximeter 7 Accessories A. A lanyard B. Two batteries C. A pouch D. An External SpO2 Probe (optional) E. A User Manual F. Quality Certificate Note：The accessories are subject to change. Detailed items and quantity see the packing List. -
Page 17: Cleaning And Disinfecting Instruction
Fingertip Pulse Oximeter • Please take out the batteries if the oximeter will not be used for a long time. • The best storage environment of the device is -25ºC to 70ºC ambient temperature and less than 93% relative humidity. •... - Page 18 Fingertip Pulse Oximeter is required, use a 1:10 bleach solution. • Then surface-clean with a cloth saturated with clean water and dry with a clean, soft cloth. Caution: Do not sterilize by irradiation steam, or ethylene oxide. Do not use the sensor if it is damaged. - 12 -...
-
Page 19: Troubleshooting
Fingertip Pulse Oximeter 9 Troubleshooting Trouble Possibe Reason Solution Display Maybe the Please shake the direction oximeter is not oximeter with a doesn’t used for a long certain force to change or time, the movable make the changes metal ball within movable metal insensitively. - Page 20 Fingertip Pulse Oximeter Trouble Possible Reason Solution 1. The finger is not 1. Place the Placed far finger SpO2 enough inside. correctly 2. The finger is inside and Pulse shaking or the try again. Rate patient is moving. 2. Let the display patient keep instable...
- Page 21 Fingertip Pulse Oximeter Manufacturer North-vision Tech. Inc. Address: 1st Fl., No.15, Gongye E. 2nd Rd., East Dist., HsinChu City 30075, Taiwan R.O.C. International Sales North-vision Tech. Inc. Address: 1st Fl., No.15, Gongye E. 2nd Rd., East Dist., HsinChu City 30075, Taiwan R.O.C.
- Page 22 Fingertip Pulse Oximeter European Representative: CMC Medical Devices & Drugs S.L. C/Horacio Lengo N 18, CP 29006 Malaga, Spain TEL: +34951214054 FAX:+ 34952330100 - 16 -...