Summary of Contents for KKT KOLBE PREMIUM FREE6020ED
Page 1
User’s manual for your cooker hood Models: FREE6020ED FREE9020ED Version: 1.2 / 151209...
Page 2
Hints and symbols Dispose of the dishwasher packaging material correctly. All packaging materials can be recycled. Plastic parts are marked with the standard international abbreviations: (e.g. PS for polystyrene, padding material) This appliance is identified according to the European guideline 2002/96/EC on waste electrical and electronic equipment -WEEE.
Page 3
Safety informations • Keep children away from the unit. The operation of the device by child- ren is permitted only under adult supervision. • The device is designed for household operation and is to be used exclu- sively for that. •...
Table of content Overview 1. General notes 1.1 Intended use 1.2 Protection of the environment 1.3 Tips and general advice 2. Before using the hood 3. Using the hood 3.1 Operating safety information 3.2 In exhaust air mode 3.3 In circulation air mode 4.
General notes 1. General notes 1.2 Protection of the environment 1.1 Intended use 1.2.1 Package The packing materials are 100% recyc- lable. Comply with local regulations for their disposal. The appliance is intended for domestic use. The manufacturer is not responsible for damage resulting from improper use or maloperation.
General notes 2. Before using the hood of the heater or other non-electric opera- ted appliances. c) No flambé dishes are to be prepared under the extractor hood. The open flames could destroy the hood or even cause a kitchen fire. Ensure that the hood has not suffered d) Never leave pans unwatched when damage during transport.
Safety 3.3 In circulation air mode The inlet air is filtered through a carbon • Due to the fire risk, frying or cooking filter (also known as active carbon filter) with oils and fats under the hood is and circulated in the room. The carbon only to take place under constant filter captures the odours produced surveillance.
Care and cleaning 4. Care and cleaning Special information for appliances with a stainless steel casing Prior to any maintenance or cleaning A commercially available non-abrasive work, isolate the hood from the electrical stainless steel cleaning agent should be supply by: used for cleaning stainless steel surfaces.
Care and cleaning cause unpleasant odours. After washing, • Foam grease filters must be soaked the washable and regeneratable carbon once a month in warm soapy water for filter must be reactivated. This is carried 1 to 2 hours. Do not wring out; repeat out by drying the cleaned filter in an oven where required and replace the filter for 10 minutes at 100°C.
Fault – what to do if... 6. Fault – what to do if ... When the lightning fails: Motor problems • Is there a power supply failure? • Does the lamp need changing? • Is the plug properly inserted in the •...
Installation 7. Installation 7.1 Installation data / dimensions On installation, the minimum distance Minimum distance from the lower edge of between the hob and the hood must be the hood body: exactly complied with (see chapter 7.1 to ceramic and cast cooking hobs 45 cm. “Installation data“) and follow the num- to gas hob 55 cm.
Installation Only connect the appliance to the power Never install the appliance if the data supply once it is properly installed. on the rating plate does not agree with your supply voltage. 7.2 Using the extractor hood as You will find the rating plate inside the an exhaust air hood (with air appliance, behind the grease filter.
Installation 9. Control panel Descriptions: E: Power increase A: Lamp Filter / Cleaning / Set time F: Alarm B: Automatic after-running G: Light On/Off C: Power decrease D: Digital display...
Page 17
Installation Filter cleaning: Setting the time: If the symbol A (filter cleaning) is flashing, When you press the button A for 3 se- the unit remembers it, clean the filter, or conds, the time will flash on your screen. swap it. After the filter has been cleaned By repeatedly pressing the A button to and re-inserted into the extractor hood, show the hour (using the arrow keys C...
Troubleshooting 10. Troubleshooting Problem Possible causes Solution Air flap jammed Rectify jamming Light on, but motor does not Faulty capacitor Change capacitor Motor bearing faulty Change motor Suspicious smell from Change motor motor Light not on, motor does not The following are possible in addition to the above causes Faulty lamps...
Installation 11. Exhaust air pipeline be a large temperature drop within the individual parts of the pipeline, resulting in sweating or condensation water production. This renders outlet pipeline insulation necessary. • In some cases a condensation water barrier must be installed in addition to adequate insulation 1: Air outlet to outdoors 2: Air outlet via an air shaft...
Installation of the hood 12. Before installation 1 Clean the area thoroughly before installation, so that at the first time, no dust or debris can be aspirated. 2 The exhaust hose must not be routed together with gas pipes, hot-air pipes, etc.
Page 21
Installation of the hood 12.2 Installation instruction Preparations a) Specify the exact location of the hood and make sure that the power supply is on the right place. Before you start with the assembly, drill all relevant holes for installation of the exhaust hose (must be available or made).
Page 22
Installation of the hood 4. Mounting the flue a) Put the telescopic shaft in the ground slot. b) the slide so completed chim- ney shaft on the motor housing and pull out the telescopic shaft to the desired height to define the optimal position of the mounting bracket.
Page 23
Installation of the hood The images are intended just for illustrati- on purposes.
Page 24
We wish you much success with the appliance. Version: 1.2 / 151209...