Leader Board Set-Up - RaceAmerica 64835A Manual

Total Dims:
Mounting:
Housing:
View Filter:
View Range:
Power Reqt:
Weight (total):

LEADER BOARD SET-UP

The display consists of five two digit
enclosures which mount to a customer supplied
frame structure. Locate the appropriate mounting
diagram based on model number and left/right
scoreboard as follows:
Scoreboard No. of
Model No. Positions
64835A 5
64835B 5
64830A 10
64830B 10
The enclosures utilize guide pins to assemble
the enclosures together. The bottom enclosure is
attached to the structure first. Follow the steps
below for cable connections and mounting for
each Position Display.
STEP 1 - Mounting Position 5 and 10
Attach the bottom unit (highest number)
to the vertical frame structure with four 3/8-16
hex head machine screws. 110VAC or 230VAC
AC power is connected to this unit via the NEMA
watertight enclosure located behind the position
number (see step 6).
STEP 2 - Mounting Position 4 and 9
Locate the round wire circular interconnect
cable connectors (Figure 2) and attach it to the
mating connector on the top of Position 5/10
(Figure 3). Locate the guide pins on the top of
Position 5/10 and slide them into the mating holes
54"W x 151" H x 4"D
3/8-16 PEM nuts on back
Powder coated aluminum
Red Transparent acrylic
1000' in full sun
110/230 VAC 250W
40#/enclosure x 5 ~200#
Mounting
1to5 6to10
Fig 1 n/a
n/a Fig 2
Fig 1 Fig 1
Fig 1 Fig 2
RaceAmerica Racetrack Leader Boards
on the bottom of Position 4/9 (Figure 4). Place
one 8-32x.375 screw in the bottom left corner of
Position 4/9. Secure Position 4 to the vertical
frame structure with four 3/8-16 hex head screws
(Figures 5a and 5b).
STEP 3 - Mounting Position 3 and 8
Locate the round wire circular interconnect
cable connectors (Figure 2) and attach it to the
mating connector on the top of Position 4/9 (Figure
3). Locate the guide pins on the top of Position 4/9
and slide them into the mating holes on the bottom
of Position 3/8 (Figure 4). Place one 8-32x.375
screw in the bottom left corner of Position 3/8.
Secure Position 3/8 to the vertical frame structure
with four 3/8-16 hex head screws (Figures 5a and
5b).
STEP 4 - Mounting Position 2 and 7
Locate the round wire circular interconnect
cable connectors (Figure 2) and attach it to the
mating connector on the top of Position 3/8
(Figure 3). Locate the guide pins on the top of
Position 3/8and slide them into the mating holes
on the bottom of Position 2/7 (Figure 4). Place
one 8-32x.375 screw in the bottom left corner of
Position 2/7. Secure Position 2/7 to the vertical
frame structure with four 3/8-16 hex head screws.
STEP 5 - Mounting Position 1 and 6
Locate the round wire circular interconnect
cable connectors (Figure 2) and attach it to the
mating connector on the top of Position 1/6 (Figure
3). Locate the guide pins on the top of Position
1/6 and slide them into the mating holes on the
bottom of Position 1/6 (Figure 4). Place one
8-32x.375 screw in the top left corner of panel
position 2/7(Figures 5a and 5b). Secure Position
1 to the vertical frame structure with four 3/8-16
hex head screws. Install the antenna to the antenna
connector located on the front upper left side.
Antennas are mounted and positioned upright.
5