3M PELTOR WS LiteCom Pro III Manual
Hide thumbs
Also See for PELTOR WS LiteCom Pro III:
- Manual (286 pages) ,
- Fitting instructions manual (6 pages) ,
- Manual (285 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for 3M PELTOR WS LiteCom Pro III
Summary of Contents for 3M PELTOR WS LiteCom Pro III
- Page 1 3M™ PELTOR™ WS™ LiteCom Pro III © 3M Svenska AB Värnamo, Sweden...
-
Page 2: Table Of Contents
Introduction ........................3 3M™ PELTOR™ WS™ LiteCom Pro III Headset ............3 Intended Use ........................ 3 Important ........................3 Before Use Headset Warnings ................4 Hearing Protector Warnings ..................4 Note ..........................4 6 EN 352 Safety Statements ..................5 Proper Use Intrinsic Safety Warnings .............. -
Page 3: Introduction
MT73H7P3E4D10NA 3 Intended Use These 3M™ PELTOR™ headsets are intended to provide workers with protection against hazardous noise levels and loud sounds while allowing the user to communicate with built-in two-way radio or Bluetooth®. It is expected that all users read and understand the provided user instructions as well as be familiar with the use of this device. -
Page 4: Before Use Headset Warnings
For proper use, read user instructions, talk to your supervisor or call 3M™ Technical Service. If your hearing seems dulled or you hear a ringing or buzzing during or after any noise exposure (including gunfire), or for any other reason you suspect a hearing problem, leave the noisy environment immediately and consult a medical professional and/or your supervisor. -
Page 5: 352 Safety Statements
With Lithium ion batteries, there is a risk of fire and burns. Do not open, crush, heat above 55°C (131°F), or incinerate. Use of other battery packs then ACK081 (Non intrinsic safe) or (intrinsic CAUTION: safe) may cause an explosion. © 3M Svenska AB Värnamo, Sweden... -
Page 6: Proper Use Intrinsic Safety Warnings
If there is any risk that the safety or integrity of the unit has been compromised, the unit must be taken out of operation immediately and removed from the potentially explosive atmosphere without delay. Action must be taken to prevent the device from being accidentally placed into operation again. Contact 3M Technical Service for service and repair. -
Page 7: Statements
8.3 CE statement Declaration of Conformity Hereby, 3M Svenska AB declares that WS™ LiteCom Pro III (MT73H7*4D10**-**) is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. © 3M Svenska AB Värnamo, Sweden... -
Page 8: Overview Of Ws™ Litecom Pro Iii
ACK081 for regular use. They must be charged via two special cables. Both cables must be connected to a wall adapter called This equipment has the same digital working characters when operating in both two digitized voice/data mode. © 3M Svenska AB Värnamo, Sweden... -
Page 9: Technical Data
Shelf life headset: 5 year Shelf life battery pack: 1 year Weight: Model Weight MT73H7A4D10** 490g MT73H7F4D10**-50 521g MT73H7B4D10**-** 475g MT73H7P3E4D10**-** 512g Color: Cups: light blue (intrinsic safe) and dark blue (non intrinsic safe) Headband: black © 3M Svenska AB Värnamo, Sweden... -
Page 10: Technical Data, Electrical
Expected operating time (according to standardized measurement) in room temperature with ACK081 is: High power: ~16 h Medium power: ~17 h Low power: ~18h External input: 4-pole connector for external equipment, 3M™ Peltor type J111-A 10.4 Technical data, Radio Frequency range: 406.1 - 470 MHz Operation mode:... -
Page 11: Modes Of Operation
Charging time is approx. 3 h, a LED will indicate with green light when the charging is complete. May not be charged if ambient temperature exceeds 45º C. ACK081 and can be charged in a powered off headset, or separately. © 3M Svenska AB Värnamo, Sweden... -
Page 12: Menu System
Volume source Volume increased source decreased 10 s with ina ctivity or M button short short press on press. + and -. Menu No voice guide in main menu. © 3M Svenska AB Värnamo, Sweden... - Page 13 Active sound source PTT, VOX or Phone call receiver ended activity. Radio Surround BT call Rx/Tx Radio activity BT device wants ended + 5s. to have a call. Stream started Stream stopped BT stream © 3M Svenska AB Värnamo, Sweden...
- Page 14 First press on + or – gives full voice guide, another press within 1s on same button gives only the number. Max or min value is indicated with a beep. © 3M Svenska AB Värnamo, Sweden...
-
Page 15: Quick Guides
4 short press on either + or - button middle button. middle button. to adjust radio volume. ”VOX on” ”VOX off” VOX on VOX off Double press on Double press on PTT button. PTT button. © 3M Svenska AB Värnamo, Sweden... -
Page 16: Replacing Ack081 And
Bluetooth pairing. ”Connected” LiteCom Pro III Find WS LiteCom Pro III on your phone and connect. Replacing ACK081 and 13.1 Insert the rechargeable battery in the battery compartment. 13.2 Push down the latch. © 3M Svenska AB Värnamo, Sweden... -
Page 17: Interfaces
2, 25 mV Microphone input = 10 mV output External audio input levels EN 352-6: Input signal level pin 3 U (mV, RMS) Mean sound pressure level in cup(dB(A)) Standard Deviation Sound Pressure (dB) 28,1 70,8 49,9 75,8 88,8 80,8 157,9 85,7 © 3M Svenska AB Värnamo, Sweden... -
Page 18: Spare Parts And Accessories
3M™ PELTOR™ AL2AH Battery charging cable for 3M™ PELTOR™ Power Supply 3M™ PELTOR™ FL5602-50 External PTT for WS™ LiteCom Pro III Headset. Push-To-Talk button with connection cable for external control of transmission with the radio in the 3M™ PELTOR™ WS™ LiteCom Pro III Headset. -
Page 19: Non Intrinsic Safe
With PELTOR J11 connector (type Nexus TP-120) for use with a PELTOR adapter and an external communication radio. Contact your Authorized 3M™ PELTOR™ WS™ LiteCom Pro III Headset dealer for more information. Product spare parts: 3M™ PELTOR™ HY83 Hygiene kit Hygiene kit consisting of two foam pads, two foam rings and snap-in ear cushions. -
Page 20: Settings
Following settings can be adjusted/configured by authorized dealers: Automatic power off Microphone gain Level dependent Channels Channels settings Device settings Radio settings Squelch Your dealer can also update different firmware on your headset. Restore factory defaults: Explained under menu operation. © 3M Svenska AB Värnamo, Sweden...
Need help?
Do you have a question about the PELTOR WS LiteCom Pro III and is the answer not in the manual?
Questions and answers