Intel bay trail-d j1900 quad core cpu, on board ddr3l, 3 x intel lan/usb/vga/com, all-in-one intel bay trail-i d j1900, 2.0 ghz vga, pcie mini card, m.2 b key sata multi-lan board, 4 x usb, 2 x com (69 pages)
Intel mobile ivy bridge processor + (pch)qm77 / ddr3 1333 / 1600 mt/s / lan / dvi/ hdmi /audio /usb / pcie mini card (110 pages)
Summary of Contents for Lex Computech 2I385S
Page 1
2I385S Intel Bay Trail-D J1900 (Quad Core )CPU, On Board 2GB DDR3L 1333 MT/s, 2 x LAN ,2 x HDMI, USB All-In-One Intel Bay Trail-I D1900(Quad Core 2.0 GHZ )CPU, 2 x Intel GbE LAN , 2 x PCIe mini card slots , 1 x HDMI, 1 x Mini HDMI,Audio, SATA, USB, Mirco USB, Wide Range DC-IN NO.
2-1 UNPACKING PRECAUTION ..................2-2 UNPACKING CHECKUP ....................2-3 DIMENSION-2I385S ....................2-4 LAYOUT-2I385S-CONNECTOR AND JUMPER ............2-4-1 LAYOUT-2I385S-CONNECTOR AND JUMPER BOTTOM .......... 2-5 DIAGRAM-2I385S ......................2-5-1 BOTTOM SIDE DIAGRAM-2I385S ................2-6 LIST OF JUMPERS ...................... 2-7 JUMPER SETTING DESCRIPTION ................
Page 3
4-3 GETTING HELP ......................4-4 MENU BARS ........................ 4-5 MAIN ..........................4-6 ADVANCED ........................4-6-1 BOOT CONFIGURATION ..................4-6-2 PCI EXPRESS CONFIGURATION ................4-6-2-1 PCI EXPRESS ROOT PORT 1/2/3/4 ..............4-6-3 USB CONFIGURATION .................... 4-6-4 VIDEO CONFIGURATION ..................4-6-5 THERMAL CONFIGURATION .................. 4-6-6 SATA CONFIGURATION ..................
Page 4
Copyright This manual is copyrighted and all rights are reserved. It does not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer.
Warning ! Battery Batteries on board are consumables. The life time of them are not guaranteed. 2. Fless solution with HDD The specifi cation & limitation of HDD should be considered carefully when the fanless solution is implemented. We will not give further notifi cation in case of changes of product information and manual.
Hardware Notice Guide 1. Before linking power supply with the motherboard, please attach DC-in adapter to the motherboard fi rst. Then plug the adapter power to AC outlet. Always shut down the computer normally before you move the system unit or remove the power supply from the motherboard.
Graphics chipset. This integrated platform offers superb performance and PC specifi cation in the industry. Despite the limited space of 2I385S, it supports 1 ports of Hi-Speed USB 3.0 / 2.0 and 2 ports of USB 2.0 to enhance the host controller interface which will ensure the high performance level and fl...
1-1 Major Feature 1. Intel BayTrail-D D1900 2.0GHz SOC (Quad core) 2. Intel BayTrail-D Integrated Graphics chipset, 688 MHz render clock frequency 3. On board DDR3L SDRAM 2GB Memory, data transfer rate of 1333MT/s 4. Support 2 x 10/100/1000 Mbps Intel LAN ports 5.
1-3 Installing the Mini PCI-e Card 2. Install a mSATA card at the angle of 45°. 1. Unfasten the round-headed M2*6 (The half size Mini PCI-e slot supports mSATA) screw for half size Mini PCI-e. 3. Fasten a round-headed M2*6 screw.
1-4 Directions for installing the Mini Card 1. Unscrew the screw on the board 2. Plug in the Mini Card in a 45 angle 3. Gently push down the Mini Card and screw the screw back.
1-5 Packing List Material Code Description Detail Specifi cation Quantit 7G1901-1590001-0 MB-2I385S-D92-001 LF,2I385S-D92,Rev.:001 6G8001-2196-0400 Manual LF,M/B,2I385S 6G8006-2349-0100 LEX Product Driver DVD LF, Intel Baytrail Driver,Windows 7/8.1 32/64 6G6003-7330-0100 Power Cable LF,L=9cm,2.0 1*4/DC JK *The packing list above is for the users who purchase single motherboard. The users who purchase the board with chassis may refer to the packing list in the Assembly Guide.
1. Ground yourself by a grounded wrist strap at all times when you handle the 2I385S. Well secure the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object.
2-2 Unpacking checkup First of all, please follow all necessary steps of section 2-1 to protect 2I385S from electricity discharge. With reference to section 1-5 please check the delivery package again with following steps: 1. Unpack the 2I385S board and keep all packing material, manual and driver disc etc, do not dispose ! 2.
2-5 Diagram- 2I385S 5 Diagram 2I385S JSB1 SWP11 MPCE1 CBAT1 MPCE2 SWP1 LED1 JLED2 CU31 HDMI2 HDMI1 CPO1 CPI1 Front Panel Power Button Line out Mic In Micro USB...
2-6 List of Jumpers JSB1: CMOS DATA clear 2-7 Jumper Setting Description A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an open circuit without the plastic cap. Some jumpers have three pins, labeled 1, 2, and 3.
2-8 JSB1: CMOS Data Clear A battery must be used to retain the motherboard confi guration in CMOS RAM. Close Pin1 and pin 2 of JSB1 to store the CMOS data. To clear the CMOS,follow the procedures below: 1. Turn off the system and unplug teh AC power 2.
Chapter-3 Connection This chapter provides all necessary information of the peripheral's connections, switches and indicators. Always power off the board before you install the peripherals. 3-1 List of Connectors BAT1: Li 3V battery holder CBAT1: Li 3V battery 2pin (1.25mm) wafer CA1: Line out Phoen Jack CA2: Mic In Phoen Jack CA3: Line-out/Line-in/Mic-in/SPDIF-out 2x5 pin (2.0mm) Wafer (Option)
3-3 CMOS Battery connector BAT1: 3V Battery hold 2pin BAT1: Battery use Li 3V / 220mAh (CR2032) Note: 1. When board without Adaptor plug in, this board power RTC consumption about 2.7uA 2. If adaptor always plug in RTC power consumption about 0.1uA CBAT1 pin1 BAT1...
3-4 DC+12V /+5 Voltge output CPO1: +12V/+5V DC voltage output (1 X 4 pin 2.0mm Black wafer) PIN NO. Description +12V* *Note: 1. DC in +12V by switch to DC-out voltage +12V, so DC in need stable +12V input 2. Mating connector: JST B4B-PH-KL or compatible 3.
WDT For F75111N I C watch dog timer device: DC spec : Input low Voltage (VIL):+0.8 Max , Input High Voltage(VIH) : +2V Min Output low Current (IOL):10mA (Min) VOL=0.4V Output High Current (IOH):-10mA (Min) VOH=2.4V Watch Dog Time value 0~255 sec The system will be issued reset.
3-10 USB Interface CU1: USB3.0/2.0 port (Type A connector) PIN NO. Description PIN NO. Description USB 3.0 TX+ USB 2.0 D- USB 3.0 TX- USB 2.0 D+ USB 3.0 RX+ USB 3.0 RX- Note: 1. USB 3.0 and USB 2.0 combo Type A Jack 2.
3-15 SATA Interface SATA1: SATA connectors ( Option ) PIN NO. Description DATA TX+ DATA TX- DATA RX- DATA RX+ Note: 1. SATA1 support SATA 2.0 spec update 6Gb/sec . 2. CPO1 provide SATA HDD power +12V, GND, +5V 3. The SATA signal share with mSATA of MPCE1, but just one can be worked in same time.
Chapter-4 Introduction of BIOS The BIOS is a program located in the Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gains control. The BIOS fi rst operates an auto-diagnostic test called POST (Power on Self Test) for all the necessary hardware, it detects the entire hardware devices and confi...
4-2 BIOS Menu Screen & Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us fi rst see a short description of the function keys you may use here: Press ←→...
4-3 Getting Help Status Page Setup Menu/ Option Page Setup Menu Press F1 to pop up a help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>.
4-4 Menu Bars There are six menu bars on top of BIOS screen: Main To change system basic confi guration Advanced To change system advanced confi guration Security Password settings Power PME & Power button settings Boot Exit Save setting, loading and exit options. User can press the right or left arrow key on the keyboard to switch from menu bar.
4-6-2-1 ► PCI Express Root Port 1/2/3 Control the PCI Express Root Port. The optional settings are: Enabled(default), Disabled. Select PCI Express port speed. The optional settings are: Gen1(default), Gen2 Select PCIE TXE ROM support The optional settings are: Disabled(default), Enabled 4-6-3 USB Confi...
4-6-4 Video Confi guration Confi gure CRT as Enable or disable CRT function. The optional settings are: CRT(default) or Default Confi gure DDI0 as Enable or disable HDMI function. The optional settings are: HDMI(default) or disabled. Confi gure DDI1 as Enable or disable Mini HDMI function.
4-6-5 Thermal Confi guration Thermal Confi guration Parameters This Value controls the temperature of the ACPI Critical Trip Point, the point in which the OS will shutdown the system. Critical Trip point is the shutdown temperature, the default value is 110˚ The CPU frequency will auto reduce when cpu temperature arrived to passive Trip point.
4-6-6 SATA Confi guration SATA Controller Use this item to Enable or Disable SATA Device. The optional settings are: Enabled(default) or Disabled Chipset SATA Mode Determine how SATA controller(s) operate. The optional settings are: IDE Mode(default), AHCI Mode. SATA Speed Indicates the maximum speed the SATA controller can support.
SATA Port 0 Connected to an ODD Use this item to Enable or Disable SATA Port0 ODD function The optional settings are: Enabled(default) or Disable SATA Port 1 Connected to an ODD Use this item to Enable or Disable SATA Port1 ODD function The optional settings are: Enabled(default) or Disable 4-6-7 ACPI Table/Features Control ACPI Table/Features Control...
4-7 Security Supervisor Password To set up an Supervisor password 1. Select Supervisor Password. The screen then pops up an Create New Password dialog. 2. Enter your desired password that is no less than 3 characters and no more than 10 characters. 3.
4-8 Power Wake on PME Determines the action taken when the system power is off and the PCI power management Enable wake up event occurs. The optional settings: Enabled, Disabled(default) Power Button Instant OFF(default) : The system will be turn off directly when push the power button. Delay 4 sec : The system will be turn off when push the power button for 4 sec.
4-9 Boot Boot type Select boot type for Dual type ,Legacy boot type or UEFI boot type, default is Dual boot type Quiet Boot The optional settings are: Enabled(default), Disabled. EFI / Legacy Device order Determine EFI device fi rst or legacy device fi rst. The optional settings: EFI device fi...
4-9-2 Boot Type Order Boot Type Order Setting the boot type priority. The default settings is 1.USB drive 2.Hard Disk Drive 3.CD/DVD ROM drive 4.Others...
4-10 EXIT Exit Saving Changes This item allows user to reset the system after saving the changes. Save Change Without Exit This item allows user to saving the changes but doesn’t restart. Exit Discard Changes This item allows user restart the system but no saving the changes Load Optimal Default Use this item to restore the optimal default for all the setup options.
4-11 Device Manager Please press the key F10 when boot up to go into the Device Manager menu 4-11-1 SIO FINTEK81801U Power Failure This item specifi es whether your system will reboot after a power failure or interrupt occurs. [Keep state] Restores the system to the status before power failure or interrupt occurred. (default) [Always on] Leaves the computer in the power on state.
4-11-2 Hardware Monitor Press [Enter] to view PC health status. This section shows the status of your CPU, Fan, and overall system. This is only available when there is Hardware Monitor function onboard.
Chapter-5 DRIVER INSTALLATION There is a system installation DVD in the package. This DVD does not only include all the drivers you need but also some other free application programs and utility programs. In addition, this DVD also includes an auto detect software telling you which hardware is installed and which driver is needed so that your system can function properly.
5-1 INF Install Intel Baytrail Chipset Driver (example for WIN8 64bit) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Intel® Chipset Device Software" menu" screen, click "INF". screen, click "Next". 3. At the "License Agreement" 4. At the "Readme File Information" screen, screen,click "Yes"...
Page 59
5. Click "Next" 6. Click "Finish" & restart computer. NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 64/32-bit, X:\driver\INTEL\BAY\INF\WIN7\infi nst_autol.exe For Windows 8 / 8.1 32/64-bit X:\driver\INTEL\BAY\INF\WIN_8_64\infi nst_autol.exe...
5-2 VGA Install Intel Baytrail VGA Driver (example for WIN8 64bit) 1. At the"AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu"screen, click "VGA". screen, Click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" screen, Click "Yes"...
Page 61
6. Click "Finish" to restart computer 5. At the "Setup Progress" screen, Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32-bit, X:\driver\INTEL\BAY\VGA\WIN_7_32\Setup.exe For Windows 7 64-bit X:\driver\INTEL\BAY\VGA\WIN_7_64\Setup.exe For Windows 8 / Windows 8.1 32-bit X:\ \driver\INTEL\BAY\VGA\WIN_8_32\Setup.exe For Windows 8 / Windows 8.1 64-bit X:\driver\INTEL\BAY\VGA\WIN_8_64\Setup.exe...
5-3 Serial IO Install Driver Baytrail Serial IO Driver (FOR Windows 7 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup menu" screen, click "Serial IO". Programscreen, Click "Next". 3. At the "License Agreement" screen, 4.
Page 63
5. At the "Ready to install the program" screen, 6. Click "Finish" and restart computer Click "Install" NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32-bit, X:\driver\INTEL\BAY\SERIALIO\WIN7_32Bit.msi For Windows 7 64-bit X:\driver\INTEL\BAY\SERIALIO\Win7_64Bit.msi...
5-4 xHCI Install Intel USB 3.0 xHCI Driver (FOR Windows 7 only) 1. At the"AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu" screen, click "xHCI". screen, Click" Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" screen, Click "Yes".
Page 65
6. Click "Finish" to restart computer 5. At the "Setup Progress" screen, Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, X:\driver\INTEL\BAY\XHCI\Driver_Installer\Setup.exe...
5-5 HD Audio Install High Defi nition Audio Driver (example for WIN8 64bit) 1. At the "AUTOMATIC DRIVER 2. Click "Next". INSTALLATION menu", click "HD Audio" 3. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, Windows 8/8.1 32 / 64-bit X:\driver\INTEL\BAY\SOUND\Win7_Win8_Win81_R273.exe...
5-6 MBI Install Intel MBI Driver (FOR Win 8/8.1 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu", click "HD Audio" screen, Click “Next”. 3. At the "License Agreement" screen, 4. At the "Setup Progress" screen, Click "Yes".
Page 68
5. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 8/8.1 32 / 64-bit, X:\driver\INTEL\BAY\MBI\Setup.exe...
5-7 TXE Install Intel TXE driver 5-7-1 TXE Install for WIN8/WIN8.1 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Setup" screen, Click "Next". menu", click "TXE" 3. At the "License Agreement" screen, 4. Click "Next". Click "Yes".
Page 70
5. Click "Finish" & restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 8 32 / 64-bit, X:\driver\INTEL\BAY\TXE\WIN_8\SetupTXE.exe For Windows 8.1 32 / 64-bit, X:\driver\INTEL\BAY\TXE\WIN_8.1\SetupTXE.exe...
5-7-2 TXE Install for WIN7 Please install PXE Patch fi rst. 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Windows Update" screen, menu", click "TXE Patch " Click "Yes". 3. Click "Finish" & restart computer 4. At the "AUTOMATIC DRIVER INSTALLATION menu", click "TXE "...
Page 72
5. At the "TXE Setup" screen, Click "Next". 6. At the "License Agreement" screen, Click "Yes". 8. Click "Finish" & restart computer 7. Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, TXE Patch X:\driver\INTEL\BAY\TXE\WIN_7\kmdf-1.11-Win-6.1-x86.msu X:\driver\INTEL\BAY\TXE\WIN_7\kmdf-1.11-Win-6.1-x64.msu...
STEP 3. Copy the latest BIOS for your LEX motherboard from our website to your bootable disc. STEP 4. (Here take 2I385S as an example, please enter your motherboard’s name) Insert your bootable disc into X: (X could be C:, A: or others.
Appendix A: Power Consumption Test Condition Item Spec Celeron J1900 2 Ghz Memory DDR3L 1333 2GB Operating System Windows 7 / SP1 Test Program 3D Mark 06 HDD 2.5" SATA Slim Type HDD mSATA 32GB Test Result for reference only ! Start up Operation Shut down...
Appendix C: F75111N I C DIO device 1-1 IO Device:F75111 under DOS The Sample code source you can download from http://tprd.info/lexwiki/index.php/IO_Device:F75111_under_DOS Source fi le: F75111_Dos_Src.rar Binary fi le: F75111_Dos_Bin.rar USERNAME & PASSWORD: sf How to use this Demo Application 1.Boot Ms-Dos Operating System 2.execute "75WDT.EXE"...
1-2 IO Device: F75111 under Windows The Sample code source you can download from Source fi le: F75111_DIOSrc.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111 Binary fi le: F75111_DemoBin.rar USERNAME & PASSWORD: sf How to use this Demo Application 1. Press the "Start" button to test DIO function 2.
Page 78
p.s. f75111 send "F75111_SetWDTEnable(BYTE byteTimer)" including a parameter "timer", if there's no disable signal (F75111_SetWDTDisable()) to stop it before timer countdown to 0, System will reboot. if there's disable signal received, resent Enable WDT signal, for a loop to prevent from reboot Introduction Initial Internal F75111 port address (0x9c) defi...
Disable WatchDog void F75111_SetWDTDisable () WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); // Disable WatchDog 1-3 IO Device: F75111 VB6 under Windows The Sample code source you can download from Source fi le: 75111_VB_v10.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111_VB6 Binary fi le: 75111_VB_Src.rar USERNAME & PASSWORD: sf How to use this Demo Application A Function - Enable WDT timer ,Key-in the value by seconds then system will reboot after value which you key-in in left text box !! B Function - Disable WDT timer ,Push down the button then WDT timer value will be clear !!
Page 81
SDK Function Introduction Function EnableWDT Function EnableWDT(timer As Integer) Call WriteI2CByte(&H3, &H3) Call WriteI2CByte(&H37, timer) Call WriteI2CByte(&H36, &H73) End Function Function DisableWDT Function DisableWDT() Call WriteI2CByte(&H36, &H0) End Function Function SetDOValue Function SetDOValue(dovalue As Integer) Call WriteI2CByte(&H23, &H0) Call WriteI2CByte(&H20, &HFF) Call WriteI2CByte(&H2B, &HFF) Call WriteI2CByte(&H21, dovalue) End Function...
1-4 IO Device: F75111 under linux The Sample code source you can download from Source fi le: F75111v2.0L.tar.gz http://tprd.info/lexwiki/index.php/IO_Device:F75111_under_linux Binary fi le: F75111v2.0LBin.tar.gz USERNAME & PASSWORD: sf How to compile source code 1. Compile source code with Code::Blocks download and install the Code::Block with command "apt-get install codeblocks" Open an exist project(F75111.cbp) in Code::Blocks, click the compile button ( add an option 'pkg-confi...
Page 83
1. Press the "Start" button to test DIO function 2. Press the "Enable" button to test WDT function 3. Press the "Disable" button to disable WDT 4. Check the "Enable Loop" box and press "Enable" to do WDT loop test 5.
Need help?
Do you have a question about the 2I385S and is the answer not in the manual?
Questions and answers