+050001490 - rel. 1.0 - 20.11.2012
pGD touch 7"
Terminale utente pGD Touch 7" - User terminal pGD Touch 7"
Installazione e montaggio / Assembly and installation
Dimensioni e forature / Dimensions and drilling template (in mm/inc.)
A
drilling template
L
Fig.1
Model
A
B
C
pGD 7
176 (06.90")
136 (05.35")
45 (01.77")
Fig.2
Nota: avvitare ogni vite di fi ssaggio fi no a quando l'angolo della cornice poggerà
sul pannello. Togliere la pellicola protettiva del display. / Screw each fi xing screw
until the bezel corner gets in contact with the panel. Remove the protective fi lm
from the display.
Applicazione guarnizione / Applying the gasket
B
A
3
2
1
guarnizione lato a righe
striped side gasket
Fig.3
Legenda:
A.
Guarnizione / Gasket
B.
Foratura per il montaggio / Installation cut-out
Attention: montare la guarnizione con la parte liscia verso il terminale (fi gura). Se la
guarnizione è danneggiata o sporge oltre il terminale, il livelo di protezione IP65 non è
assicurato. / mount the gasket with the fl at part towards the terminal (fi gure) If the gasket is
damaged or extends past the terminal, the IP65 protection level is not guaranteed.
Sostituzione batteria / Battery replacement:
Per accedere alla batteria per la sostituzione o lo smaltimento, è necessario
togliere l'alimentazione al terminale e rimuovere il coperchio posteriore
(svitare le 4 viti agli angoli). Utilizzare batterie al litio mod BR2330 (non
ricaricabili). / To access the battery for replacement or disposal, power down
the device and remove the rear cover (remove the 4 screws on the corners).
Use model BR2330 lithium batteries (non-rechargeable).
Attenzione! sussiste il pericolo d'esplosione se la batteria è sostituita con
altre di tipo errato. / Warning! danger of explosion if an incorrect battery
is used.
Rete Ethernet (solo PGDT07000F120) / Ethernet network
(PGDT07000F120 only)
Le due porte ethernet sono collegate ad un hub-switch interno che sgrava il
terminale dalla gestione del traffi co ethernet in transito sulla rete. E' quindi possibile
realizzare una rete di più dispositivi senza utilizzare hub esterni. Lo switch è dotato
di Auto–MDIX (auto crossover) che permette di realizzare la rete utilizzando normali
cavi patch (dritti) senza la necessità di cavi cross per connettere due dispositivi (NIC).
E' importante ricordare che, in assenza di alimentazione del terminale, il traffi co di
passaggio dalla porta 1 alla 2, e viceversa, si interrompe.
Per i collegamenti ethernet utilizzare cavi schermati CAT-5 STP.
The two Ethernet ports are connected to an internal hub-switch that manages the
Ethernet traffi c transiting over the network for the terminal. Consequently, a network of
several devices can be created without requiring an external hub. The switch features
Auto–MDIX (auto crossover), meaning the network can be created using normal patch
cables, without needing crossover cables to connect two devices (NIC). It must be
remembered that when the terminal is not powered, traffi c from door 1...2 and vice-
versa is interrupted. For the Ethernet connections use CAT-5 STP shielded cables.
Signifi cato LED sul connettore RJ45 /
Green -
Meaning of LED on RJ45 connector
Link/Act
Introduzione
Il terminale grafi co pGD Touch da 7 pollici appartiene alla famiglia di terminali touch screen
pensata per rendere semplice e intuitivo l'interfacciamento dell'utente con i controlli della
famiglia pCO Sistema. La tecnologia elettronica utilizzata e il nuovo display a 64K colori
permettono di gestire immagini di alta qualità e funzionalità avanzate per ottenere un
elevato standard estetico. Il pannello touch screen, inoltre, facilita l'interazione uomo-
macchina rendendo, di fatto, più facile la navigazione tra le varie schermate.
Codici modelli
Codice
PGDT07000FR00
PGDT07000F120
Contenuto confezione
• pGD Touch;
• connettori alimentazione e RS485;
• Kit ganci fi ssaggio con viti;
• foglio istruzioni.
Avvertenze per l'installazione
Per una installazione a regola d'arte rivolgersi ad installatori abilitati. Evitare il montaggio del
terminale in ambienti che presentino le seguenti caratteristiche:
• umidità relativa maggiore di quanto indicato nelle specifi che tecniche;
• forti vibrazioni o urti;
• esposizione ad atmosfere aggressive ed inquinanti (es.: gas solforici e ammoniacali,
C
4mm
0.16"
nebbie saline, fumi) con conseguente corrosione e/o ossidazione;
• elevate interferenze magnetiche e/o radiofrequenze (evitare quindi l'installazione delle
macchine vicino ad antenne trasmittenti);
• esposizione all'irraggiamento solare diretto e agli agenti atmosferici in genere;
H
L
• ampie e rapide fl uttuazioni della temperatura ambiente;
147 (05.79")
187 (07.36")
Tab. 1
• ambienti ove sono presenti esplosivi o miscele di gas infi ammabili.
Avvertenze generali
Devono essere rispettate le seguenti prescrizioni:
• per le reti di comunic. Ethernet e RS485 utilizzare esclusivamente cavi schermati;
• una tensione di alimentazione elettrica diversa da quella prescritta può danneggiare
seriamente il sistema;
• utilizzare capicorda adatti per i morsetti in uso. Allentare ogni vite ed inserirvi i capicorda,
quindi serrare le viti. Ad operazione ultimata tirare leggermente i cavi per verifi carne il
corretto serraggio;
• non aprire il prodotto quando è alimentato;
• l'uso a temperature particolarmente basse può causare una visibile diminuzione
della velocità di risposta del display. Questo è da ritenersi normale e non è indice di
malfunzionamento.
Aggiornamento HMI Runtime e/o applicazione
Copiare il pacchetto di aggiornamento (fi le .ZIP) contenente il runtime
o l'applicazione, oppure entrambi, a seconda delle opzioni scelte al
momento della generazione di "Update package" con 1Tool-TE, in una
chiavetta USB e successivamente collegare la chiavetta al pGDTouch.
Tenere premuto il dito sullo schermo del terminale pGD Touch per
alcuni secondi fi no a che non sarà visualizzato il menù contestuale:
guarnizione lato liscio
Selezionare "Update"
flat side gasket
display
per avviare la
procedura di
aggiorn. Runtime e/o
applicazione. L'utility
per l'aggiornamento
si avvierà ed apparirà
la seguente fi nestra:
retro display
rear display
Impostazioni di sistema
Tenere premuto il
dito sullo schermo
del terminale pGD
Touch per alcuni
secondi fi no a che
non sarà visualizzato
il menu contestuale:
I tasti Next e Back consentono di far scorrere, a rotazione, le varie funzioni fi no ad evidenziare
in celeste quella desiderata, la pressione sulla box in celeste avvia alla funzione selezionata.
Nome
Descrizione
funzione
Calibrate
Consente la ricalibrazione del touch screen. Utilizzare un pennino e premere con
touch
precisione sulle crocette seguendo le indicazioni proposte.
Display
Accede al menu di sistema per settare il tempo di autospegnim. della backlight e regolarne
settings
l'intensità. Default = 5' . Non bisogna disabilitare l'impostazione di autospegnimento
Time
Consente la regolazione dell' o rologio di sistema e del fuso orario (impostare sempre GMT)
BSP
Version: Mostra la versione del sistema operativo
Settings
Timers: mostra le ore di funzionamento del sistema e della back light
Buzzer: permette di attivare il suono del buzzer al tocco del touch screen
Network Mostra gli attuali dati IP del sistema
(vedi fi g. seguente) (indirizzo, subnet,
Gateway, DHCP, DNS) e permette di
accedere al menu di confi gurazione
della porta ethernet
Set
Impostazione dell'indirizzo del dispositivo
device
per i protocolli che lo richiedono
address
(Modbus RTU Server, Bacnet). E' possibile
(new
modifi care l'indirizzo dei soli protocolli
version)
che stanno girando. Selezionare la porta
di comunicazione (Ethernet, Com1, Com2)
Fig. 4
usando i tasti freccia in alto.
Verifi care che il protocollo sia quello
desiderato. Usare il tastierino numerico per inserire l'indirizzo rispettando i valori
minimo e massimo. Il tasto
cifre. Il valore di default viene assegnato tramite 1ToolTE editor. Il tasto Cancel annulla la
modifi ca, il tasto OK, se il valore immesso è valido, rende eff ettiva la modifi ca, altrimenti
visualizza un messaggio di errore.
Caratteristiche tecniche
Display
Tipo
Risoluzione
Area attiva del display
Colori
Retro-illuminazione
Regolazione luminosità
Angolo visivo (CR ≥10)
Contrasto (min.)
Tempo di risposta (max.)
Temper. del colore (CIE)
Luminosità (min.)
Uniformità (min.)
Risorse di sistema
Yellow - On/Off=
Sistema operativo
100MBps/10MBps
Microprocessore
Memoria utente
RAM
Interfaccia utente
Touchscreen
Fig. 5
Indicatori LED sistema
Descrizione
Versione BASIC
Versione ADVANCED
Selezionare
"Auto select
best match" e
premere next,
in questo
modo verrà avviata la procedura di
aggiornamento. Attendere che la procedura
sia terminata e premere "Close".
Selezionare
"Show system
settings";
apparirà la
schermata
principale del
programma di confi gurazione (fi gura a lato).
rimuove l'ultima cifra, il tasto Clear rimuove tutte le
LCD TFT
800x480 (WVGA);
7" diagonale, 16/9
64 K
LED
Si
Alto / Basso
Sinistra / Destra = 60 / 50 deg. 60 / 60 deg.
250 (Φ=0°)
Tr =10 ms; Tf =16 ms
Bianco (Ø = 0°) x = 0.249 ÷ 0.349; y = 0.278 ÷ 0.378
180 cd/m2
70 %
Microsoft Windows CE 6.0
TI AM3505 – 600MHz
128 MB Flash
256 MB DDR2
Resistivo
1 verde e 1 rosso
Introduction
The pDG Touch 7 inch graphic terminal belongs to the family of touch screen terminals
designed to make user interface with controllers in the pCO system family easy and
intuitive. The electronic technology used and the new 64K colors display allows high quality
images and advanced functionality to obtain a high aesthetic standard. The touch screen
panel also facilitates human-machine interaction making it easier to navigate between the
various screens.
Model codes
Code
Description
PGDT07000FR00
BASIC Version
PGDT07000F120
ADVANCED Version
Contents of the package
• pGD Touch;
• power supply connectors and RS485;
• Attachment hook kit with screws;
• instruction sheet.
Warnings for installation
For state-of-the-art installation, contact qualifi ed installers. Avoid installing the terminal in
environments with the following characteristics:
• relative humidity greater than that indicated in the technical specifi cations;
• strong vibrations or impacts;
• exposure to aggressive and polluting atmospheres (i.e.: sulphuric and ammonia gases,
salt vapours, smoke) with subsequent corrosion and/or oxidation;
• high magnetic and/or radio interference (therefore, avoid installing machines near
transmitting antennas);
• exposure to direct sunlight and weather in general;
• wide and rapid temperature fl uctuations;
• areas where there are explosives or mixtures of fl ammable gases.
General warnings
The following requirements must be met:
• for Ethernet and RS485 communication networks, only use shielded cables;
• a power supply voltage that diff ers from the one required could seriously damage the
system;
• use wire terminals suitable for the terminal boards in use. Loosen each screw and insert
the wire terminal then tighten the screws. When the operation is complete, pull the
cables slightly to make sure they are properly tightened;
• do not open the product when it is under power;
• particularly low temperatures could cause a visible decrease in the response speed on
the display. This is considered normal and is not a sign of malfunction.
HMI Runtime and/or application update
Copy the update package (.ZIP fi le) containing the runtime or the
application or both according to the options chosen when generating
the "Update package" with 1Tool-TE to a USB drive and then connect
the drive to the pGDTouch. Hold your fi nger on the pGDTouch
terminal for a few seconds until the menu is displayed:
Select "Update... " to
Select "Auto
start the Runtime
select best
and/or application
match" and
update procedure
press next;
The update utility
this starts
will start and the
the update
procedure. Wait for the procedure to fi nish
following window
and press "Close".
appears:
System settings
Hold your fi nger
Select "Show
on the pGDTouch
system
terminal for a few
settings";
seconds until the
the main
menu is displayed:
confi guration
program
screen will appear (following fi gure).
The Next and Back buttons allow you to scroll through the various functions until you
highlight the one you wish in light blue. Pressing on the light blue box starts the selected
function.
Function
Description
name
Calibrate
Recalibrates the touch screen. Use a stylus and carefully press the crosses following the
touch
proposed indications.
Display
Access the system menu to set the backlight auto shut off time and adjust the
settings
brightness. Default = 5' . Auto shut off does not need to be disabled
Time
Allows the adjustment of the system clock and time zone (always set at GMT)
BSP
Version: Shows the operating system version
Settings
Timers: shows the hours of operation of the system and the backlight
Buzzer: allows you to activate the buzzer sound when touching the touch screen
Network Shows the current IP data of the system
(see following fi g.) (address, subnet,
Gateway, DHCP, DNS) and allows access
to the ethernet port confi guration
menu
Set
Setting the device address for protocols that
device
require it (Modbus RTU Server, Bacnet). The
address
address can only be changed for protocols
(new
that are running. Select the communication
version)
port (Ethernet, Com1, Com2) using the
arrow keys at the top. Make sure the
protocol is the one you want.
Use the numeric keypad to insert the address, within the minimum and maximum
values. The key
removes the last number, the Clear key removes all the numbers.
The default value is assigned through 1ToolTE editor. The Cancel key cancels the
change, the OK key makes the change eff ective if the value entered is valid, otherwise
an error message is displayed.
Technical characteristics
Display
Type
LCD TFT
Resolution
800x480 (WVGA);
Active display area
7" diagonal, 16/9
Colors
64 K
Backlighting
LED
Brightness control
Si
ViewingAngle (CR ≥10)
Top / Bottom
Left / Right = 60 / 50 deg.
Contrast ratio (min.)
250 (Φ=0°)
Response Time (max.)
Tr =10 ms; Tf =16 ms
Color chromaticity (CIE)
White (Ø = 0°) x = 0.249 ÷ 0.349; y = 0.278 ÷ 0.378
Luminance (min.)
180 cd/m2
Luminance Uniformity (min.)
70 %
System resources
Operating system
Microsoft Windows CE 6.0
Microprocessor
TI AM3505 – 600MHz
User memory
128 MB Flash
RAM
256 MB DDR2
User interface
Touchscreen
Resistive
System LED indicators
1 green and 1 red
60 / 60 deg.
Need help?
Do you have a question about the pGD touch 7 and is the answer not in the manual?
Questions and answers