Page 1
Service Instructions Digital Minilab d-lab.1 Type 8070/050 / Type 8070/100 Type 8070/200 / Type 8070/300 Capacitor Kit Order number DD+18070312D0 Edition 2004-07-08 Version English, 04073_00...
Capacitor Kit d-lab.1 Content List of possibly affected machines ...................... 1 Contents of the kit..........................1 Additional tools..........................1 Modification ............................2 Some general points before you start.................... 2 Information ............................. 2 3.2.1 Problem ..........................2 3.2.2 Countermeasure........................ 2 Preparation ............................ 2 3.3.1...
Capacitor Kit d-lab.1 List of possibly affected machines Only a few machines are affected. So it is necessary to check the capacitors before they are replaced. All Print Engines with modification code „B06“ or higher have already correct capacitors installed.
10V may have been mounted. 3.2.2 Countermeasure To only way to overcome the problem is to replace the concerned capacitors. To replace the LCD driver board from another d-lab.1 is not possible, because this board and the print engine are paired! Preparation 3.3.1...
Page 6
Capacitor Kit d-lab.1 Remove light cover of print engine Unlock the print engine. If you remove the print engine from the trails, you have better access to the LCD driver board. AGFA d-lab.1 CM+9.8072.9003.0/DD+18070312D0/PN04073_00...
Page 7
Modification Capacitor Kit d-lab.1 Remove the upper cover of the print engine. Remove the cover of the LCD driver board (6 screws), use socket wrench 5.5 mm AGFA d-lab.1 CM+9.8072.9003.0...
Capacitor Kit d-lab.1 How to check the capacitors Only two capacitors are critical and have to be replaced if they are not correct. As the removal of the LCD driver board is also critical, we suggest not to remove the board when you check the capacitors.
Modification Capacitor Kit d-lab.1 3.4.1 Wrong and correct capacitors Wrong capacitors can be identified as follows: Yellow color: „107A“ or „10V“ on top Black color: „100-10“ on top Correct capacitors have „107D“ or „20V“ on top AGFA d-lab.1 CM+9.8072.9003.0...
Capacitor Kit d-lab.1 Replacement of the capacitors 3.5.1 Removal of the LCD driver board Remove the side cover of the print engine Remove both connectors AGFA d-lab.1 CM+9.8072.9003.0/DD+18070312D0/PN04073_00...
Page 11
Modification Capacitor Kit d-lab.1 On the LCD driver board remove the screw which holds the heat sink. This can be done only with a socket wrench 5.5 mm. It is necessary to fix the screw from the other side. At the LCD driver board remove the flat cable, please be very careful!! 1.
Page 12
Capacitor Kit d-lab.1 Open the 4 screws of the plugs From now on please wear the ESD wrist band! now it is possible to remove the LCD driver board. AGFA d-lab.1 CM+9.8072.9003.0/DD+18070312D0/PN04073_00...
Modification Capacitor Kit d-lab.1 3.5.2 Removal of the wrong capacitors To remove the 2 capacitors, use a pair of tweezers First remove C136, then C3 Use the solder wick to clean the 4 soldering points AGFA d-lab.1 CM+9.8072.9003.0...
Capacitor Kit d-lab.1 3.5.3 Installation of the new capacitors Both capacitors are the same, so it is not possible to mix them up. The only thing you have to take care is the polarity! If it is wrong, the capacitor will be destroyed! First install C3 Put some solder on one of the 2 points.
Modification Capacitor Kit d-lab.1 3.5.4 Reinstallation of the LCD driver board The resinstallation has to be done very carefully, otherwise fluctiations of the print quality will come up. Before you install the heat sink on the board, put some heat sink compount on all 4 ICs and on the heat sink.
Capacitor Kit d-lab.1 Attachment List of possibly affected machines, sorted by serial number. Country Order number Date of delivery Taiwan 70071311 10.05.2004 Japan 70062788 26.05.2004 Deutschland VA 26537 05.05.2004 Deutschland VA 26657 11.05.2004 Australia 70058029 12.05.2004 Morocco 70042375 06.02.2004 70039649 02.02.2004...
Attachment Capacitor Kit d-lab.1 List of possibly affected machines, sorted by country Country Order number Date of delivery Algeria 70070301 05.05.2004 Argentina 70051981 14.05.2004 Argentina 70051982 24.05.2004 Argentina 70051983 27.05.2004 Argentina 70070876 22.06.2004 Australia 70058029 12.05.2004 Australia 70032423 10.02.2004 Australia 70047071 23.04.2004...
Page 28
Capacitor Kit d-lab.1 Belgium 70056283 28.05.2004 Belgium 70056737 24.05.2004 Belgium 70053296 28.05.2004 Belgium 70084962 17.06.2004 Belgium 70085305 17.06.2004 Belgium 70061692 22.06.2004 Bolivia 70078612 25.06.2004 Brasil 70038276 28.02.2004 Brasil 70059227 04.05.2004 Brasil 70059227 26.05.2004 Brasil 70064931 03.06.2004 Brasil 70064940 15.06.2004 Brasil 70064933 18.06.2004...
Page 29
Attachment Capacitor Kit d-lab.1 Deutschland 70062499 18.05.2004 Deutschland 70048735 17.05.2004 Deutschland 70054362 27.05.2004 Deutschland 70054766 25.05.2004 Deutschland 70077157 14.06.2004 Deutschland 70081664 14.06.2004 Deutschland 70054362 17.06.2004 Deutschland 70084018 25.06.2004 Deutschland 70083444 24.06.2004 Dubai 70046254 04.05.2004 Dubai 70057903 12.05.2004 England 70038963 23.02.2004...
Page 30
Capacitor Kit d-lab.1 France 70046991 23.03.2004 France 70047022 14.04.2004 France 70046221 17.04.2004 France 70039319 16.04.2004 France 70074126 13.05.2004 France 70060719 05.05.2004 France 70057999 28.04.2004 France 70067585 05.05.2004 France 70058115 30.04.2004 France 70065584 29.04.2004 France 70061189 13.05.2004 France 70066922 19.05.2004 France 70067493 27.05.2004...
Need help?
Do you have a question about the d-lab.1 and is the answer not in the manual?
Questions and answers