Summary of Contents for Endress+Hauser Proline Promag 50
Page 1
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Brief Operating Instructions Proline Promag 50 Electromagnetic Flow Measuring System These Brief Operating Instructions are not intended to replace the Operating Instructions provided in the scope of supply.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Safety instructions Safety instructions Designated use • The measuring device is to be used only for measuring the flow of conductive liquids in closed pipes.
Page 4
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Safety instructions Proline Promag 50 • All parts of the device must be included in the potential equalization of the system. • Cables, certified cable glands and certified dummy plugs must be suitable to withstand the prevailing operating conditions, such as the temperature range of the process.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Safety instructions Safety conventions Warning! "Warning" indicates an action or procedure which, if not performed correctly, can result in injury or a safety hazard.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 Installation Transporting to the measuring point • Transport the measuring device to the measuring point in the original packaging.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation Installation conditions 2.2.1 Dimensions For the dimensions of the measuring device, see the associated Technical Information on the CD-ROM.
Page 8
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 Partially filled pipes Partially filled pipes with gradients necessitate a drain-type configuration. The empty pipe detection (EPD) function offers additional protection by detecting empty or partially filled pipes.
Page 9
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation 2.2.3 Orientation An optimum orientation helps avoid gas and air accumulations and buildup in the measuring tube. The measuring device, nevertheless, supplies a range of functions and tools to measure problematic fluids correctly: •...
Page 10
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 Inlet and outlet runs If possible, install the sensor upstream from fittings such as valves, T-pieces, elbows, etc. The following inlet and outlet runs must be observed in ³...
Page 11
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation 2.2.5 Foundations, supports If the nominal diameter is DN ≥ 350 (≥ 14"), mount the sensor on a foundation of adequate load-bearing strength.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 Installing the Promag L sensor " Caution! • The protective covers mounted on the two sensor flanges (DN 50…300) are used to hold the lap joint flanges in place and to protect the PTFE liner during transportation.
Page 13
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation 2.3.3 Screw tightening torques (Promag L) Please note the following: • The tightening torques listed below are for lubricated threads only.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation Installing the W sensor Note! Screws, nuts, seals, etc. are not included in the scope of supply and must be supplied by the customer.
Page 18
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 2.4.3 Screw tightening torques (Promag W) Please note the following: • The tightening torques listed below are for lubricated threads only.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation Installing the Promag P sensor " Caution! • The plates mounted on the two sensor flanges protect the PTFE which is turned over the flanges and, consequently, should not be removed until immediately prior to mounting the sensor.
Page 24
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 2.5.3 Installing the high-temperature version (with PFA lining) The high-temperature version has a housing support for the thermal separation of sensor and transmitter.
Page 25
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation 2.5.4 Tightening torques for threaded fasteners (Promag P) Please note the following: • The tightening torques listed below are for lubricated threads only.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 Installing the Promag H sensor Depending on the order specifications, the sensor is supplied with or without ready-mounted process connections. Mounted process connections are fixed to the sensor with 4 or 6 hexagonal-headed bolts.
Page 29
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation • Grounding rings, incl. seals, are mounted inside the process connections. The face-to-face length is not affected. Installing the grounding rings...
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 Installing the transmitter housing 2.7.1 Turning the transmitter housing Turning the aluminum field housing Aluminum field housing for non-Ex area £...
Page 31
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation 2.7.2 Turning the onsite display Press in the side latches on the display module and remove the module from the cover plate of the electronics compartment.
Page 32
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Installation Proline Promag 50 Pipe mounting " Caution! mm (inch) Danger of overheating! If the device is mounted on a Ø 20…70 warm pipe, make sure that the housing temperature (Ø...
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Installation Post-installation check • Is the measuring device damaged (visual inspection)? • Does the device correspond to specifications at the measuring point, including process temperature and pressure, ambient temperature, minimum fluid conductivity, measuring range, etc.?
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Wiring Proline Promag 50 Wiring Warning! Risk of electric shock! Components carry dangerous voltages. • Never mount or wire the measuring device while it is connected to the power supply.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Wiring Connecting the various housing types Wire the unit using the terminal assignment diagram inside the cover. 3.1.1 Compact version...
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Wiring Proline Promag 50 Connecting the remote version connecting cable 3.2.1 Connecting cable for Promag W, P and L Connecting cable termination Terminate the signal and coil current cables as shown in the figure below (Detail A).
Page 37
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Wiring 3.2.2 Promag H connecting cable Connecting cable termination Terminate the signal and coil current cables as shown in the figure below (Detail A).
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Wiring Potential equalization Perfect measurement is only ensured when the medium and the sensor have the same electrical potential. Most sensors have a reference electrode installed as standard, which guarantees the required potential connection.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Wiring Proline Promag 50 Degree of protection The devices meet all the requirements for IP 67. After mounting in the field or service work, the following points have to be observed to ensure that IP 67 protection is retained: •...
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Hardware settings Hardware settings This section only deals with the hardware settings needed for commissioning. All other settings (e.g. output configuration, write protection, etc.) are described in the associated Operating Instructions on the CD-ROM.
Page 42
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Hardware settings Proline Promag 50 PROFIBUS Device address range: 0 to 126 OFF ON Factory setting: 126 Miniature switches for device address Example shown:...
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Hardware settings Terminating resistors Note! If the measuring device is used at the end of a bus segment, termination is required.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Commissioning Proline Promag 50 Commissioning Switching on the measuring device On completion of the installation (successful post-installation check), wiring (successful post-connection check) and after making the necessary hardware settings, where applicable, the permitted power supply (see nameplate) can be switched on for the measuring device.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Commissioning Proline Promag 50 Navigating within the function matrix > 3 s – – – – A0007562 → Enter the function matrix (starting with measured value display) →...
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Commissioning Calling the Commissioning Quick Setup All the functions needed for commissioning are called up automatically with the Quick Setup.
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Commissioning Proline Promag 50 Software settings 5.5.1 Device address Has to be set for measuring devices with the following communication methods: • PROFIBUS DP/PA → device address range 0 to 126, factory setting 126 The device address can be configured via: •...
Page 49
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Commissioning Endress+Hauser Page 49 of 52 Page 49 of 52 Q-Pulse Id Q-Pulse Id VM454 Active 30/09/2014 Active 30/09/2014...
Page 50
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Commissioning Proline Promag 50 Endress+Hauser Page 50 of 52 Page 50 of 52 Q-Pulse Id Q-Pulse Id VM454 Active 30/09/2014 Active 30/09/2014...
Page 51
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction Proline Promag 50 Commissioning Endress+Hauser Page 51 of 52 Page 51 of 52 Q-Pulse Id Q-Pulse Id VM454 Active 30/09/2014 Active 30/09/2014...
Page 52
Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instruction KA00026D/06/EN/14.11 71154524 FM+SGML 9.0 Page 52 of 52 Page 52 of 52 Q-Pulse Id Q-Pulse Id VM454 Active 30/09/2014 Active 30/09/2014...