Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nautilus CORE HEALTH & FITNESS HDP6D
Summary of Contents for Nautilus CORE HEALTH & FITNESS HDP6D
- Page 1 CORE HEALTH & FITNESS HDP6D Dampened Platform OWNER’S MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ........................2 IMPORTANT LABEL LOCATIONS ........................4 PRODUCT SPECIFICATIONS ........................5 ASSEMBLY ........................6 TOOLS ..............6 PROCEDURE - BB2 PLATFORM ..............6 PROCEDURE - SA ..............13 MAINTENANCE ........................17 SUPPORT & SERVICE ........................18 Page 1... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING! Before using this product, it is essential to read the ENTIRE Owner’s Manual and ALL installation instructions. The Owner’s Manual describes equipment setup and instructs members on how to use correctly and safely. Read all warnings posted on the machine. Health related injuries may result from incorrect or excessive use of exercise equipment. - Page 4 All equipment MUST be secured (bolted and tightened) to a solid, level surface, using all of the anchoring holes provided, to stabilize and eliminate rocking or tipping over. Shim any mounting surface that does not rest thoroughly on the floor using flat washers, DO NOT force the foot to contact the ground with anchors.
-
Page 5: Important Label Locations
IMPORTANT LABEL LOCATIONS This page shows examples of the warning labels and communication stickers placed on the equipment as part of the manufacturing process. It is critical that own- ers maintain the integrity and placement of these stickers. If you find any stickers missing or damaged the replacement numbers are shown on the support site. See Support and Service to order replacements. -
Page 6: Product Specifications
PRODUCT SPECIFICATIONS Fig. 3 HDP6D-BB2 HDP6D Dampened Platform Overall Weight Lifting Area Width Length Height Max User Weight 76.1 x 95 x 4 in 193.3 x 241.3 x 10.2 cm Fig. 4 HDP6D-BB2-SA HDP6D Dampened Platform Stand-Alone Overall Weight Lifting Area Width Length Height... -
Page 7: Assembly
ASSEMBLY TOOLS Required Tools (Assembly Only): • Metric Allen Key Set • Metric Open-Ended Wrench Set • Large Adjustable Crescent Wrench PROCEDURE - BB2 PLATFORM Install the trim tension rod into the rear of the top dampening platform. Fig. 5 Move the platform assembly built in Step 1 into position in the rack. - Page 8 Slide the center platform into position up against the top platform assembly - ensure that the tension rod properly engages with the barrel nut on the underside of the platform. Fig. 8 Use an 11/16” open-ended wrench to turn the trim tension rod to secure the top and center platforms together.
- Page 9 Install the spotter platform onto the rack. Fig. 11 Secure the spotter platform to the rack using two (2) 5/16 black pine tree clips, then finish securing the platform using a T10 TORX screwdriver and four (4) 5/16” 1/4-20 x 3/4 pan head screw. T10 TORX Fig.
- Page 10 Use an 18mm open-ended wrench to secure the back left and back right weldment tubes to the rack using two (2) pieces each of the M12 washer and M12 x 65mm bolt. 18mm Fig. 14 Use an 8mm allen key to secure two (2) nut plates to the inside of the front sleeve using four (4) pieces each of the M12 flat washer and M12 x 30mm button head...
- Page 11 Use an 8mm allen key to fully tighten the hardware from Step 11 to secure the front weldment tubes into the front sleeve. Fig. 17 Use a 5/8” open-ended wrench to secure the front tube weldment assembly built in Step 13 to the center platform using one (1) piece each of the M12 flat washer, 7/16”...
- Page 12 Install a corner sleeve onto each end of a side tube weldment then use an 8mm allen key to tighten the hardware from Steps 15+16. Repeat Step 17 to build a total of two side tube with corner sleeves assemblies. Fig.
- Page 13 Fig. 23 Fig. 24 Install the six (6) polyurethane rebond Install the six (6) middle pads onto the top of the foam pads into the platform frame. rebond foam pads. Install the rubber mat wings, textured side up, onto the top of the middle pads. Fig.
-
Page 14: Procedure - Sa
PROCEDURE - SA Use an 8mm allen key to secure two (2) nut plates to each corner sleeve using four (4) pieces each of the M12 flat washer and M12 x 30mm button head cap screw - DO NOT FULLY TIGHTEN. Repeat Step 1 to build a total of four (4) corner sleeve assemblies. - Page 15 Install two of the assemblies built in Steps 3+4 into a front sleeve built in Step 5. Use an 8mm allen key to tighten the hardware to secure the assemblies to the front sleeve. Repeat Steps 7+8 to build a total of two (2) of these assemblies.
- Page 16 Slide the second front tube assembly built in Steps 7-9 onto the ends of the side tubes - DO NOT FULLY TIGHTEN. Fig. 33 Install the six (6) polyurethane rebond foam pads into the platform frame. Fig. 34 Install the six (6) middle pads onto the top of the rebond foam pads.
- Page 17 Install the rubber mat wings, textured side up, onto the top of the middle pads. Fig. 36 Use a 5/8” open-ended wrench to secure the front tube assembly from Step 12 to the bamboo platform using one (1) piece each of the 7/16”...
-
Page 18: Maintenance
MAINTENANCE MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping the product in safe operating condition. Failure to conduct preventative maintenance by the owner may cause the product to operate in an unsafe manner. Equipment needs to be inspected and maintained at regular intervals per the preventative maintenance schedule provided in this manual. -
Page 19: Support & Service
SUPPORT & SERVICE For Technical Support, Service, Parts Orders or any Customer Service needs, please contact us direct by phone, email, or through our 24 hour support site: GLOBAL SUPPORT CENTER 4400 NE 77th Avenue, Suite 300 Vancouver, WA 98662 Tel: (360) 326-4090 •... - Page 20 PART NUMBER 19-7997, REV A All rights reserved. Star Trac, the Star Trac logo and StairMaster are registered trademarks of Core Health & Fitness, LLC. Schwinn and Nautilus are registered trademarks of Nautilus Inc. used under license to Core Health & Fitness LLC. Throwdown is a registered trademark of Throwdown Industries, LLC.