Related Manuals for Radial Engineering Reamp X-Amp
Summary of Contents for Radial Engineering Reamp X-Amp
- Page 1 True to the Music ® USER GUIDE Radial Engineering Ltd. #1165 - 1845 Kingsway Ave, Port Coquitlam BC V3C 1S9 Tel: 604-942-1001 • Fax: 604-942-1010 Email: info@radialeng.com...
-
Page 2: Table Of Contents
Radial XAMP REAMP ® ® ™ User Guide Table of Contents Page Overview ................. 1 Input Panel ..............2 Output Panel ..............3 Getting Ready To Remap ..........5 Connecting And Using The X-Amp ......... 6 Adjusting Levels And Adding A Second Amp ....7 Using With Keyboards And Voice ........ -
Page 3: Overview
The X-Amp can also be used on other instruments. Keyboard tracks can be given extra life by warming up their sound by sometimes driving them through distortion pedals or tube guitar amps. Vocal tracks can also be twisted into new sounds by introducing these fun effects. Radial Engineering Ltd. X-AMP Reamper™... -
Page 4: Input Panel
6. BOOKEND DESIGN: 14 gauge steel outer shell creates a protective zone around connectors and switches. Internal welded I beam construction for maximum durability. 7. POWER LED INDICATOR: The power LED will immediately illuminate when the 15VDC supply is connected. Radial Engineering Ltd. X-AMP Reamper™... -
Page 5: Output Panel
OUT-2 into a direct and grounded output. It is factory set to LIFTED (inward position) to provide a safe and noise free connection to amplifiers. See page 9 for more information about using this feature. Radial Engineering Ltd. X-AMP Reamper™... - Page 6 It is a good idea to record the wet track (effects pedals and amplifier) at the same time with a traditional microphone set-up. This way, you can mix the original track with Reamped tracks to create new textures. Radial Engineering Ltd. X-AMP Reamper™...
-
Page 7: Getting Ready To Remap
The amp serves as an important safety ground. Before connecting a second amplifier or effect pedals you should proceed to step-3 and finish setting up your first amp. This will help test the overall system and reduce troubleshooting. Radial Engineering Ltd. X-AMP Reamper™... -
Page 8: Connecting And Using The X-Amp
OUT-2 ¼” jack. This output is transformer isolated to eliminate hum and buzz caused by ground loops, a common problem when using two amps. Dry Track Recorder Mic-1 Mic-2 Amp-1 Amp-2 Reamp Track-1 Reamp Track-2 Recording two Reamped tracks at the same time. Radial Engineering Ltd. X-AMP Reamper™... -
Page 9: Adjusting Levels And Adding A Second Amp
JDI will help eliminate potential noise caused by ground loops. Recorder Radial Tonebone Radial JDI (dry track) X-Amp Distortion Direct Box Reamp Track-1 (Reamp Effect Pedals) Reamping through a Tonebone distortion pedal and using a direct box instead of a mic. Radial Engineering Ltd. X-AMP Reamper™... -
Page 10: Using With Keyboards And Voice
OUT-2 LIFT switch and use the setting that works best. GROUND LIFT OUT-2: Use a small screwdriver to access the ground lift switch for OUT-2. Set inward to lift the ground (factory default) or outward to connect ground. Radial Engineering Ltd. X-AMP Reamper™... -
Page 11: Specifications
Weight: ....................1.55lb (720g) Shipping Size:............5”x2.75”x10.75” (127x70x273mm) Shipping Weight: ................. 2.6lb (1.18kg) Conditions:.......For use in dry locations only between 5°C and 40°C Warranty: ................. Radial 3-year, transferable *Specifications are subject to change without notice. Radial Engineering Ltd. X-AMP Reamper™... - Page 12 THREE YEAR TRANSFERABLE LIMITED WARRANTY RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from defects in mate- rial and workmanship and will remedy any such defects free of charge according to the terms of this warranty. Radial will repair or replace (at its option) any defective component(s) of this product (excluding finish and wear and tear on components under normal use) for a period of three (3) years from the original date of purchase.