Table of Contents
Advertisement
Quick Links
INTEGRATED1500LB WINCH KIT
P/N 2882798
APPLICATION
Verify accessory fitment at Polaris.com.
BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
KIT CONTENTS
This Kit includes:
REF
QTY
PART DESCRIPTION
1
1
1500 Winch Assembly
2
1
Winch Carrier
3
1
Hitch Receiver
4
1
Battery Harness - Power
5
1
Winch Harness - Jumper
6
1
Stop Bumper
7
1
Winch Hook
8
1
Storage Bag
Instr 9927951
Rev 02 2017-11
Page 1 of 12
PART NUMBER
1023692
1023484
1023486
4017356
4017355
5416562
2411836
2688505
Advertisement
Table of Contents
Related Manuals for Polaris 2882798
Summary of Contents for Polaris 2882798
- Page 1 INTEGRATED1500LB WINCH KIT P/N 2882798 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information.
-
Page 2: Tools Required
PART DESCRIPTION PART NUMBER Winch Remote - Wired (included in winch assembly) Winch Remote - Wireless 4017125 Hitch Pin Assembly 1023975 Screw - M8 x 1.25 x 25 7520877 Screw - M6 x 1.0 x 40 7518579 Nut - M6 x 1.0 7546703 Nut - M8 x 1.25 7547454... -
Page 3: Installation Instructions
If your measurement is not exactly 4 inches, then reprint template pages from electronic file using print setting “Actual Size” (not “Fit”) to obtain proper 1:1 scale. Electronic file available from your Authorized Polaris Dealer. Instr 9927951 Rev 02 2017-11 Page 3 of 12... - Page 4 5. Place rear tank cover template into position as 8. Remove battery cover and disconnect black shown and mark the location of the holes. Once negative (-) cable from battery FIRST, then marked, drill the required 1/2” holes in the rear disconnect red positive (+) cable from battery.
- Page 5 10. Install red positive (+) battery harness cable along 12. Secure the electrical connector portion of the with all other required red positive (+) cables with battery harness to the rear cargo platform by fully new longer battery bolt and threaded battery post inserting the well nuts into the previously drilled block that was provided with your kit to the positive...
- Page 6 14. Install the supplied receiver hitch with provided 17. Using a drill and 3/16” drill bit transfer drill the fasteners . Torque to specification provided three indicated mounting hole locations . After below. drilling, install provided rivets with rivet puller to secure to chassis.
- Page 7 18. Transfer drill the upper two indicated mounting 20. Replace seat and any other previously removed hole locations using a drill and 11/32” (9mm) accessories. drill bit. After drilling secure with provided 21. Your Integrated Winch Kit comes with a Lock and fasteners being sure to insert the bolts Ride Bag to store the winch accessories in.
-
Page 8: Operation
OPERATION To use the integrated winch , remove it from the carrier and place it into the receiver hitch on the IMPORTANT rear of the vehicle. ALWAYS secure it in place with the provided hitch pin making sure the R-Pin of the The winch should always be transported in the hitch pin assembly is fully seated and securely holding... -
Page 9: Wireless Remote Operation
WIRELESS REMOTE OPERATION • To use the wired remote, depress and hold the “OUT” button to extend cable. To recover cable, • When properly installed, the wireless remote will depress and hold the “IN” button. If the wired allow you to operate the winch from on or off the remote is not operating properly, see the vehicle. -
Page 10: Troubleshooting
TROUBLESHOOTING If your winch is not functioning properly, below is a short guide that can help you diagnose and correct the problem. SYMPTOM POSSIBLE CAUSES RECOMMENDED SOLUTION Dead vehicle Incorrect, damaged, or Verify all winch electrical connections are per instruction battery corroded electrical manual and free of damage and/or corrosion. - Page 11 THIS PAGE INTENTIONALLY LEFT BLANK Instr 9927951 Rev 02 2017-11 Page 11 of 12...
-
Page 12: Template Page
TEMPLATE PAGE 4.00 REFERENCE DIMENSION (INCHES) Instr 9927951 Rev 02 2017-11 Page 12 of 12...