Table of Contents
Advertisement
Quick Links
Model 4116-T300
Instruction Manual
Ka-Band Block Translator
Weather Resistant Unit
November 2015, Rev. F
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be
reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating
the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number,
equipment serial number, and a description of the part.
C
T
ROSS
ECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005 • FAX (770) 886-7964 • Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL info@crosstechnologies.com
Advertisement
Table of Contents
Related Manuals for Cross Technologies 4116-T300
Summary of Contents for Cross Technologies 4116-T300
- Page 1 Weather Resistant Unit November 2015, Rev. F Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating the equipment.
-
Page 2: Table Of Contents
All Cross Technologies, Inc. products are warranted against defective materials and workmanship for a period of one year after shipment to customer. Cross Technologies, Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall not be liable for any special, indirect, or consequential damages. -
Page 3: General
1.1 Equipment Description The 4116-T300 Ka-band Translator converts 27.5 - 31.0 GHz to 17.7 - 21.2 GHz in four selectable fixed bands and to 2.5 - 6.0 GHz for monitoring purposes. LEDs provide indication of DC Power, and PLL Alarms. The maximum gain is +20 dB. -
Page 4: Technical Characteristics
1.2 Technical Characteristics TABLE 1.0 4116-T300 Ka-Band Translator Specifications** TABLE 1.0 4116-T310 Ka-Band Translator Specifications** Input Characteristics Impedance/Return Loss 50Ω/14 dB Frequency (GHz) See Frequency (GHz) Band Chart Below 20 dB maximum gain Noise Figure, Maximum Maximum Input Level -40 to -15 dBm... - Page 5 8” Wide X 6” High X 16” Deep, Weather Resistant* Enclosure 100-240 ±10% VAC, 47-63 Hz, 30 Watts Maximum, Power FCI Clipper Series CL1M1102, Weather Resistant* Connector. **+0 to +50 degrees C; Specifications subject to change without notice. 4116-T300 Manual_F Page 5 11/05/15...
-
Page 6: Installation
A switching, ±12, +24, +5 VDC power supply provides power for the internal assemblies. The 4116-T300 can be secured to a mounting plate using the 4 holes on the bottom of the front and rear panels. (See Figure 2.5 for mounting dimensions.) Figure 2 - 4116-T300 Ka-Band Translator Front Panel 2.0.1 Connection to AC Input Power... -
Page 7: M&C Commands
2.2 M&C Commands The following tables summarize the commands and status queries applicable to the 4116-T300. * PLEASE NOTE: The two character {aa} prefix, shown in the following table, is present ONLY when RS485 is selected. Table 2.0 Model 4116-T300 M&C Commands Table 2.0: Model 4116-T300 M&C Commands... - Page 8 M&C Commands (continued) Table 2.0: Model 4116-T300 M&C Commands Command Syntax Description Set Gain {aaCGxxxx} where: xxxx = 4 characters Range: -100 to +200 (-10.0 to +20.0 in 1 dB steps) Set Serial Interface {aaCIx} where: x = 0 to select RS232...
-
Page 9: M&C Queries
2.3 M&C Queries Table 2.1: Model 4116-T300 M&C Queries Queries Syntax Description Frequency Band {aaSB} Returns {aaSBx} where: x = 1 if band 1 is selected: in = (27.5 to 28.5 GHz) x = 2 if band 2 is selected: in = (28.0 to 29.0 GHz) x = 3 if band 3 is selected: in = (29.0 to 30.0 GHz) - Page 10 = 2 if RS485 is selected if Band 5 is selected, Range: 00000 to -0500 in 5 MHz steps RS485 address Returns {aaSRxx} where: {aaSR} xx = 2 characters Range: 00 to 31 continued on page 11... 4116-T300 Manual_F Page 10 11/05/15...
- Page 11 = 1 if unit is using external reference Internal Temperature {aaST} Returns {aaSTxxx} where: xxx = 3 characters Range (-99 to +99) degrees Celsius {aaSV} Model and firmware revision returns {aaSVxxxxxxxxyyyy} where: xxxxxxxx = unit model number yyyy = unit firmware rev. 4116-T300 Manual_F Page 11 11/05/15...
-
Page 12: Ethernet Interface Installation
Contact Cross Technologies for the SNMP MIB file. 2.4.1 Methods of Connection Directly Connected to a PC: For control from a local PC, attach the 4116-T300’s Ethernet port to the Ethernet network connector on the PC using a crossover RJ-45 cable. LAN Connection For LAN connections, attach the 4116-T300’s Ethernet port to the LAN using a normal RJ-45 cable. -
Page 13: Webpage M&C
Enter the following address in a web browser to access the M&C webpage: http://<ip address of 41xx>/serial/0/setup.htm where <ip address> is the IP address of the unit. Figure 2-C (page 14) shows the product setup web page from a model 4116-T300 frequency converter. 4116-T300 Manual_F... -
Page 14: Snmp Configuration
The next screen is a “Connect To” dialog box. Select TCP/IP (Winsock) from the “Connect” drop down menu. Enter the IP address of the 4116-T300 in the “Host address:” field and 9999 in the “Port number” field. Figure 2-E shows an example of the Hyper Terminal settings required to access the SNMP configuration menu. - Page 15 IP addresses of SNMP managers that will access the unit. This is required even though SNMP traps are not implemented. The unit will not process SNMP SET and GET requests from an SNMP manager unless the IP address associated with that manager is entered in the device server. 4116-T300 Manual_F Page 15 11/05/15...
- Page 16 Figure 2-F: Device Server Configuration Menu 4116-T300 Manual_F Page 16 11/05/15...
-
Page 17: Translator Outline Drawings
Band 8 - 19.2 to 20.2 Band 9 - 18.7 to 19.7 Band 10 - 19.0 to 20.0 Band 11 - 20.0 to 21.0 1/4 - 20 Tapped Thru, 4 Places 12.00 15.5 15.875 7.50 4116-T300 Manual_F Page 17 11/05/15... -
Page 18: Physical Interface
RS422/RS485 Data In+, RS232 Data In NOTE: Planning Ethernet Access It is recommended that IP knowledgeable customer personnel be consulted as a resource in the installation and use of the Ethernet access features of the Cross Technologies product. 4116-T300 Manual_F Page 18... -
Page 19: Installation/Operation
NOTE: If a fuse continues to open, the power supply is most likely defective. 2.7.1 Connection to AC Input Power The 4116-T300 is furnished with a pre-assembled AC power input cable as described below. * 4116 * 4116-T300 AC Power Input Connections... - Page 20 ROSS ECHNOLOGIES, INC. 6170 Shiloh Road Alpharetta, Georgia 30005 (770) 886-8005 FAX (770) 886-7964 Toll Free 888-900-5588 WEB www.crosstechnologies.com E-MAIL info@crosstechnologies.com Printed in USA 4116-T300 Manual_F Page 20 11/05/15...
Need help?
Do you have a question about the 4116-T300 and is the answer not in the manual?
Questions and answers