Tsubaki PB Series Manual

Tsubaki PB Series Manual

Cam clutch

Advertisement

Thank you for buying Cam Clutch products.
Before installing or working on the product, confirm it is the correct size by checking its
label and make sure you have the complete set of parts. If any part is missing, contact
your distributor immediately.
This manual should be considered as an essential part of the unit and remain with the unit
when redistributed
●Your Cam Clutch is a high quality, sophisticated unit which should be handled by experienced engineers only.
●For safety purposes, make sure this manual is easily accessible by the user at all times.
Safety precautions in this manual are classified into two categories: "WARNING" and "CAUTION". These are defined as follows
WARNING
CAUTION
Notice that although categorized under "CAUTION", subjects discussed may lead to serious results depending on the situation.
● Make sure turning forces are not applied to Cam Clutch or turning shaft of the equipment when conducting inspection or maintenance.
Pay special attention to the back stopping application to prevent accidents.
● Frequent starting and stopping will apply excessive force on the mounting. Verify mounting strength.
● Inaccurate installation and mounting, various load conditions, wear and tear of parts, and life expectancy can all affect the performance of a
Cam Clutch. Inspect and maintain periodically and install a safety devise on your equipment.
● Comply with Ordinance on Labor Safety and Hygiene 2-1-1 general standards.
● To ensure safety and optimal performance, carefully read this instruction manual in its entirety.
● Confirm rotational direction prior to installing.
● Use the bolts with the specified strength and size, and tighten with the specified tightening torque for mounting.

■ Installation

1.
Concentricity of the inner and outer races is maintained by the plain bearing located between the outer race and the shaft.
Radial loads which work on the outer race are also supported by this plain bearing. The shaft must therefore be extended
through the clutch outer race end.
2.
Recommended shaft tolerances are as follows.
PB3, PB5, PB6, PB8
PB10, PB12, PB14
3.
The bore of the driven member, such as the sprocket on the clutch outer race, should meet H6 or H7 tolerance of the JIS
standard
Cam Clutch Manual
PB series
PB3,PB5,PB6,PB8,PB10,PB12,PB14
.
SAFETY
Death or serious injury may result from misusing the product without following the instructions.
Minor or moderate injury, as well as damage to the product may result from misusing the product
without following the instructions.
WARNING
CAUTION
Model
Shaft tolerance (mm)
+0 to -0.013
+0 to -0.016
:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PB Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tsubaki PB Series

  • Page 1 Cam Clutch Manual PB series PB3,PB5,PB6,PB8,PB10,PB12,PB14 , Thank you for buying Cam Clutch products. Before installing or working on the product, confirm it is the correct size by checking its label and make sure you have the complete set of parts. If any part is missing, contact your distributor immediately.
  • Page 2 When mounting the Cam Clutch to the shaft, apply force to the end face of the inner race or side face of the outer race keyway. Do not use the PB series Cam Clutch as a coupling. Use with a flexible coupling when connecting two shafts. Allowable ambient temperature is -5 ℃...
  • Page 3 Your cooperation is greatly appreciated. 1-1, Kohtari-Kuresumi, Nagaokakyo TSUBAKIMOTO CHAIN CO. Kyoto 617- 0833, Japan Website: http://tsubakimoto.com/ Global Associated Partners: U.S. Tsubaki Power Transmission, LLC Tsubakimoto Singapore Pte. Ltd. Tsubakimoto Europe B.V. http://www.ustsubaki.com/ http://tsubaki.sg/ http://tsubaki.eu/ Tsubaki of Canada Limited Taiwan Tsubakimoto Co.

This manual is also suitable for:

Pb3Pb5Pb6Pb8Pb10Pb12 ... Show all

Table of Contents