Electronic Function - Makita LS0815F Instruction Manual

WARNING:
• Before plugging in the tool, always check to
see that the switch trigger actuates properly
and returns to the "OFF" position when
released. Do not pull the switch trigger hard
without pressing in the lock-off button. This
can cause switch breakage. Operating a tool
with a switch that does not actuate properly
can lead to loss of control and serious personal
injury.
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
WARNING:
Do not use a lock with a shank or cable any
•
smaller than 6.35 mm in diameter. A smaller
shank or cable may not properly lock the tool in
the off position and unintentional operation may
occur resulting in serious personal injury.
• NEVER use tool without a fully operative
switch trigger. Any tool with an inoperative
switch is HIGHLY DANGEROUS and must be
repaired before further usage or serious per-
sonal injury may occur.
• For your safety, this tool is equipped with a lock-
off button which prevents the tool from unin-
tended starting. NEVER use the tool if it runs
when you simply pull the switch trigger without
pressing the lock-off button. A switch in need of
repair may result in unintentional operation and
serious personal injury. Return tool to a Makita
service center for proper repairs BEFORE fur-
ther usage.
• NEVER defeat the lock-off button by taping
down or some other means. A switch with a
defeated lock-off button may result in uninten-
tional operation and serious personal injury.

Electronic function

Soft start feature
This function allows the smooth start-up of the tool by
limiting the start-up torque.
Laser beam action
For model LS0815FL only
CAUTION:
• When not in use, be sure to turn off the laser.
► Fig.19: 1. Switch for laser
CAUTION:
• Never look into the laser beam. Direct laser
beam may injure your eyes.
• LASER RADIATION, DO NOT STARE INTO
THE BEAM OR VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS, CLASS 2M LASER
PRODUCT.
• Before shifting the laser line or performing main-
tenance adjustment, be sure to unplug the tool.
To turn on the laser beam, press the upper position
(ON) of the switch. To turn off the laser beam, press the
lower position (OFF) of the switch.
Laser line can be shifted to either the left or right side of
the saw blade by loosening the screw holding the laser
unit box and shifting it in the desired direction. After
shifting, be sure to tighten the screw.
► Fig.20: 1. Screw holding the laser unit box
Laser line is factory adjusted so that it is positioned
within 1 mm from the side surface of the blade (cutting
position).
NOTE:
• When laser line appears dim and hard to see
because of direct sunlight, relocate the work
area to a place where there is less direct
sunlight.
Cleaning of the lens for the laser light
If the lens for the laser light becomes dirty, or sawdust
adheres to it in such a way that the laser line is no
longer easily visible, unplug the saw and remove and
clean the lens for the laser light carefully with a damp,
soft cloth. Do not use solvents or any petroleum-based
cleaners on the lens.
NOTE:
• When laser line is dim and almost or entirely
invisible because of the direct sunlight in the
indoor or outdoor window-by work, relocate the
work area to a place not exposed to the direct
sunlight.
Light action
► Fig.21: 1. Light
► Fig.22: 1. Switch for light
To turn on the light, press the upper position (ON) of
the switch. To turn off the light, press the lower position
(OFF) of the switch.
CAUTION:
• Do not look in the light or see the source of light
directly.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of
lamp.
• Be careful not to scratch the lens of lamp, or it
may to lower the luminance.
ASSEMBLY
WARNING:
• Always be sure that the tool is switched off
and unplugged before working on the tool.
Failure to switch off and unplug the tool may
result in serious personal injury.
14 ENGLISH