Table of Contents
Advertisement
Operating Instructions and Parts Manual
General Power Tool
tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged
Safety Warnings
(Cont'd.)
or entangled cords increase the risk of
electric shock.
6. Never trigger the tool when not
applied to a work object.
Attachments must be securely
ing a power tool outdoors, use an
attached. Loose attachments can
extension cord suitable for outdoor
cause serious injury.
use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
7. Never point a tool at oneself or any
other person. Serious injury could
occur.
power tool in a damp location is
8. Use steady, even pressure when
unavoidable, use a residual current
using tool. Do not force. Too much
device (GFCI) protected supply. Use of a
pressure can cause blade to break
GFCI reduces the risk of electric shock.
or overheat.
Double insulated tools are equipped with
9. Keep all nuts, bolts and screws tight
a polarized plug (one plug blade is wider
and ensure equipment is in safe
that the other). This plug will fit in a
working condition.
polarized outlet only one way. If the plug
10. Do not put hands near or under
does not fit fully into the outlet, turn the
moving parts.
plug over and insert into plug again.
WORK AREA SAFETY
1. Make sure cord is located so that it
will not be stepped on, tripped over,
Keep
or otherwise subjected to damage or
work
stress.
area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not use an extension cord unless
absolutely necessary. Use of improper
extension cord could result in a risk of
fire and electric shock. If an extension
Do not operate power tools
cord must be used, make sure:
in explosive atmospheres,
• That the pins on plug of extension
such as in the presence of
flammable liquids, gases or dust.
cord are the same number, size and
Power tools create sparks which may
shape as those of plug.
ignite the dust or fumes.
• That the extension cord is properly
Keep
wired and in good electrical
children
condition.
and bystanders away while operating a
power tool. Distractions can cause you
• If an extension cord is to be used
to lose control.
outdoors it must be marked with
the suffix "W-A" or "W" following
ELECTRICAL SAFETY
the cord type designation to
indicate it is acceptable for outdoor
use. For example – SJTW-A
Power tool plugs must match
3. Do not expose to rain, snow or frost.
the outlet. Never modify the
Water entering a power tool will
plug in any way. Do not use
any adapter plugs with earthed
increase the risk of electric shock.
(grounded) power tools. Unmodified
PERSONAL SAFETY
plugs and matching outlets will reduce
risk of electric shock.
Avoid
body
watch what you are doing and use
contact with earthed or grounded sur-
common sense when operating a
faces, such as pipes, radiators, ranges
power tool. Do not use a power tool
and refrigerators. There is an increased
while you are tired or under the influ-
risk of electric shock if your body is
ence of drugs, alcohol or medication. A
earthed or grounded.
moment of inattention while operating
power tools may result in serious per-
Do not
sonal injury.
expose
power tools to rain or wet conditions.
Water entering a power tool will
increase the risk of electric shock.
Use personal protective
Do not
equipment. Always wear eye
abuse
protection. Protective equip-
the cord. Never use the cord for carry-
ment such as dust mask, non-skid safe-
ing, pulling or unplugging the power
ty shoes, hard hat, or hearing protec-
www.chpower.com
tion used for appropriate conditions
will reduce personal injuries.
tional starting. Ensure the switch is in
When
the off-position before connecting to
operat-
power source and/or battery pack, pick-
ing up or carrying the tool. Carrying
power tools with your finger on the
switch or energising power tools that
have the switch on invites accidents.
If operat-
ing a
adjusting key or wrench before turning
the power tool on. A wrench or a key
left attached to a rotating part of the
power tool may result in personal injury.
Do not overreach. Keep prop-
er footing and balance at all
times. This enables better
control of the power tool in unexpect-
ed situations.
Do not wear loose clothing or jew-
ellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be
caught in moving parts.
vided for the connection of dust
extraction and collection facilities,
ensure these are connected and proper-
ly used. Use of dust collection can
reduce dust-related hazards.
1. Hold power tool by insulated gripping
surfaces when performing an
operation where the cutting tool may
contact hidden wiring or its own cord.
Contact with a "live" wire will make
exposed metal parts of the tool "live"
and shock the operator.
2. Use clamps or another practical way
to secure and support the
workpiece to a stable platform.
Holding the work by hand or
against your body leaves it unstable
and may lead to loss of control.
Stay
alert,
this product. Excessive exposure to
vibration, work in awkward positions,
and repetitive work motions can cause
injury to hands and arms. Stop using any
tool if discomfort, numbness, tingling, or
pain occur, and consult a physician.
3. Always work in a well-
ventilated area. Wear an
OSHA-approved dust mask
and safety glasses.
4. Keep hands away from
rotating parts.
5. Always use blades with correct size and
shape (diamond vs. round) arbor holes.
2
Pernos de ajuste de corte diagonal
Prevent
uninten-
Pie en ángulo
Remove
any
Pie plano a 0°
(línea punteada)
Figura 5
Funcionamiento
AJUSTE DEL CORTE DIAGONAL
Dress
properly.
Siempre asegúrese de que la
herramienta esté apagada. Desenchufe
la herramienta. El pie puede ajustarse
hasta 45°, soltando el perno de ajuste
de corte diagonal, en la parte inferior
de la sierra (Figura 5).
If devices
Alinee en el ángulo deseado en el
are pro-
cuadrante calibrado. Luego ajuste el
perno de ajuste del corte diagonal.
Debido a la cantidad aumentada de
accionamientos de la hoja en el trabajo
y la estabilidad disminuida del pie,
la hoja puede atascarse.
Mantenga la sierra pareja y el pie
firmemente sobre la pieza de trabajo.
EXTRACCIÓN DEL POLVO
Se pueden realizar operaciones
de corte limpias conectando esta
herramienta a una aspiradora.
Introduzca la manguera de la
aspiradora en el orificio de la parte
trasera de la herramienta. Baje la
tapa para polvo antes de poner la
herramienta en funcionamiento.
Do not
misuse
Para Ordenar Repuestos o Asistencia Técnica, Llame al Teléfono 1-800-424-8936
Sirvase darnos la siguiente información:
•
Número del modelo
•
Código impreso
•
Descripción y número del repuesto según la lista de repuestos
Dirija toda la correspondencia a:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
(Cont.)
No utilice el adaptador de aspiración
cuando corte metal. Las virutas de
metal estarán calientes y podrían
encenderse dentro del dispositivo
de aspiración.
La extracción del polvo no se puede
realizar o se realiza con una eficacia
reducida cuando se hacen cortes en
diagonal.
Mantenimiento
El servicio de la herramienta debe ser
realizado sólo por personal de
reparaciones calificado. El servicio
o mantenimiento realizado por
personas no calificadas puede provocar
riesgo de lesiones.
Limpieza
Limpie el polvo y los desechos de
los orificios y contactos eléctricos,
soplando con aire comprimido.
Los orificios de ventilación del motor
y los interruptores deben mantenerse
limpios y libres de materiales extraños.
Lista de Repuestos
Descripción
Hoja de la sierra
Tubo de polvo
Guía del borde
Llave Allen de 3mm
Tornillos de fijación de la hoja (2)
23 Sp
DG460500CK
No intente limpiarla introduciendo
objetos con punta a través de las
aberturas. Mantenga los mangos de
las herramientas limpios, secos y libres
de aceite o grasa. Use únicamente un
jabón suave y un paño húmedo para
limpiar la herramienta, evitando todos
los contactos eléctricos.
Ciertos agentes de limpieza y solventes
son nocivos para los plásticos y otras
piezas aisladas. Algunos de éstos
incluyen gasolina, aguarrás, solvente
para laca, solvente de pintura,
solventes de limpieza con cloro,
amoníaco y detergentes de uso
doméstico que contengan amoníaco.
Nunca use solventes inflamables ni
combustibles cerca de las herramientas.
SERVICIO TÉCNICO
Para obtener información con relación
al funcionamiento o reparación de
este producto, sírvase llamar al
1-800-424-8936.
El servicio de la herramienta debe
ser realizado sólo por personal de
reparaciones calificado. El servicio
o mantenimiento realizado por personas
no calificadas puede provocar riesgo
de lesiones.
Al realizarle un servicio a la herramienta,
utilice únicamente piezas de repuesto
idénticas. Siga las instrucciones de la
sección Mantenimiento de este manual.
El uso de piezas no autorizadas o el no
seguir las instrucciones de
Mantenimiento puede crear un riesgo
de choque eléctrico o lesión.
Número del
Repuesto
DG025800AV
DG025900AV
DG026000AV
DG026100AV
DG029100AV
Advertisement
Table of Contents
