Related Manuals for Toro 33525
Summary of Contents for Toro 33525
- Page 1 Form No. 3433-272 Rev A Spreader Attachment Stand-on Aerator Model No. 33525—Serial No. 400000000 and Up *3433-272* A Register at www.Toro.com. Original Instructions (EN)
- Page 2 2), which signals a hazard that may cause additional information, contact an Authorized Service serious injury or death if you do not follow the Dealer or Toro Customer Service and have the model recommended precautions. and serial numbers of your product ready.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 Improper use or maintenance by the operator or Safe Operating Practices........3 owner can result in injury. To reduce the potential Safety and Instructional Decals ......5 for injury, comply with these safety instructions, Setup ................ 6 and pay attention to the safety alert symbol, which 1 Preparing the Machine........ - Page 4 • When operating with a heavy load, reduce your CAUTION speed and allow for sufficient stopping distance. The machine that the spreader accessory Use extra caution on slopes. attaches to produces sound levels in • Reduce speed and load when operating on rough excess of 85 dBA at the operator’s ear and terrain, uneven ground, and near curbs, holes, and can cause hearing loss through extended...
-
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal133-8061 133-8061 decal135-0739 135-0739 1. Impeller—off 3. Impeller—on 2. Impeller—slow 4. -
Page 6: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Bolt (3/8 x 1-1/4 inches)—30-inch machines only Locknut (1/4 inch)—30-inch machines only Bolt (1/4 x 5/8 inch)—30-inch machines Install the flow control panel. -
Page 7: Preparing The Machine
Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Engage the parking brake. Shut off the engine and remove the key. Disconnect the negative (black) battery cable from the negative (-) battery terminal. Installing the Flow Control Panel Parts needed for this procedure: Bolt (3/8 x 1-1/4 inches)—30-inch machines only... -
Page 8: Installing The Hopper Assembly
Installing the Hopper Installing the Cable-Mount Assembly Bracket Parts needed for this procedure: Parts needed for this procedure: Hopper assembly Cable-mount bracket for 24-inch machines Hairpin cotter Cable-mount bracket for 30-inch machines Hitch pin Carriage bolt (5/16 x 1 inch)—24-inch machines only Carriage bolt (1/4 x 1 inch)—24-inch machines only Procedure Locknut (1/4 inch)—24-inch machines only... - Page 9 Installing the Control Cable Parts needed for this procedure: Control cable Locknut (1/4 inch) Washer Procedure g213569 Figure 7 Ensuring that the cable ball joint is securely 1. Locknut (1/4 inch) 4. Cable end attached to the cable, connect the ball joint to 2.
-
Page 10: Installing The Wire Harness
bracket and hopper tube. Connect the spreader harness to the spreader motor as shown in Figure 8. Insert the 3 harness tie clips into the holes of the hopper mainframe to secure the harness. Installing the Wire Harness Remove the cap from the accessory wire on the main harness and plug into the spreader Parts needed for this procedure: accessory harness as shown in... -
Page 11: Installing The Cover
For 24-inch machines, use 1 cable tie to secure the cable and harness to the spring or spring mount. g253434 Figure 10 1. Cable and harness 3. Spring mount 2. Cable tie 4. Spring g221638 Figure 11 Use the remaining cable ties to secure the 1. -
Page 12: Product Overview
Product Overview Operation Note: Determine the left and right sides of the machine from the normal operating position. Important: The intended use of this spreader attachment is for dispersing grass seed. This is not to be used for fertilizer or any other chemical applications. -
Page 13: Pre-Start
Flow Control Lever Located to the right of the main controls. Lift the lever upward to start the flow and continue lifting it to increase the distribution rate. Pull the lever downward to decrease or stop the distribution rate. Distribution Limit Lock Knob Located on the right panel of the spreader accessory control panel. -
Page 14: Operating Instructions
Operating Instructions Determine the amount of product to be spread per 93 m (1,000 ft Use the recommended rate from the CAUTION Spreading Chart (page 15) or the product manufacturer’s label as a guide. Machine can spin very rapidly by positioning Determine a course length by dividing 93 1 lever too much ahead of the other. - Page 15 Spreading Chart The chart below is for reference only. Grass Seed Application at Maximum Ground Speed (Coverage 93 m or 1,000 ft Type kg (lb)/93 m (1,000 ft Gate Opening Spread Width Blue Grass or Red Top 0.9 kg (2 lb) 1.2 m (4 ft) Park, Merion, Delta, or Kentucky 0.2 kg (0.5 lb)
- Page 16 Turn on the impeller speed control. Set the impeller speed to the appropriate setting. Move the throttle to the F position and drive forward. Open the hopper gate and begin spreading. g207728 Figure 18 1. Effective spreading width—variable 1.2 to 6.7 m (4 to 22 ft) Evaluate the spread pattern.
-
Page 17: Operating Tips
Spreader Pattern Adjustment Operating Tips If the spread pattern is skewed or dispensing too light or too heavy to 1 side (Figure 19), adjust the gate Overseeding as follows: Important: Do not put down more seed than recommended by the seed company. Overseeding can cause the grass to be too thick and become susceptible to fungus. -
Page 18: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. WARNING If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch, engage parking brake, and pull the wire(s) off the spark plug(s) before you do any maintenance to the machine or attachment. -
Page 19: Adjusting The Gate Closure
Adjusting the Gate Closure Cleaning If the gate arm is not fully closing, adjust the control cable at the knob located on the cable Cleaning Debris from the mount bracket or the nuts located on either side of the hopper bracket. Machine Continue to adjust until the gate can be fully Service Interval: Before each use or daily... -
Page 20: Troubleshooting
Troubleshooting The following table lists some of the common causes of trouble. If a problem continues, contact an Authorized Service Dealer. Problem Possible Cause Corrective Action Message displays “STALLED (02)” 1. Controller has detected an excessive 1. Check the impeller and hopper for electrical current to the impeller motor. -
Page 21: Schematics
Schematics g212875 Electrical Schematic (Rev. A) - Page 22 Notes:...
- Page 23 Notes:...
- Page 24 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.