Oki C911 Product Specification page 70

Category1 Category2 Category3
System Adjust
Print Adjust Print Position
Adjust
45530603TX
Category4 Item
16K(184x260mm)[LEF]
16K(195x270mm)[LEF]
16K(197x273mm)[LEF]
8K(260x368mm)
8K(270x390mm)
8K(273x394mm)
Paper Feed MPTray
Tray1
Tray2
Tray3
Tray4
Tray5
Auto Tray Switch On
Off
Tray Sequence Down
Up
Paper Feed
Unit of Measurement inch
millimeter
Duplex Last Page Skip Blank Page
Always Print
Power Save Time 1 minute
2 minutes
3 minutes
4 minutes
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
Sleep Time 1 minute
2 minutes
3 minutes
4 minutes
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
Auto Power Off Time 1 hour
2 hours
3 hours
4 hours
8 hours
12 hours
18 hours
24 hours
Clearable Warning ONLINE
Job
Auto Continue On
Off
Manual Timeout Off
30 seconds
60 seconds
Wait Timeout Off
5 seconds
10 seconds
20 seconds
30 seconds
40 seconds
50 seconds
60 seconds
90 seconds
120 seconds
150 seconds
180 seconds
210 seconds
240 seconds
270 seconds
300 seconds
Low Toner Continue
Stop
Jam Recovery On
Off
Error Report On
Off
Hex Dump Execute
MPTray 0.00millimeter
X Adｊust
+0.25millimeter
~
+2.00millimeter
-2.00millimeter
~
-0.25millimeter
Y Adjust 0.00millimeter
+0.25millimeter
~
+2.00millimeter
-2.00millimeter
~
沖データ企業秘密・Oki Data CONFIDENTIAL
Value Default
Specifies a paper tray.
* TRAY2 to 5: Displayed only if they are installed.
* Sets the Auto Tray switching function.
* Specifies selection order priority for switching Auto Tray
Select/Auto Tray Switch.
*L Specifies the unit of custom paper size.
*A
* When Skip Blank Page is selected, the last page of an
odd-page duplex print job is printed as Simplex.
When Always Print is selected, the printer operates as
usual.
[Condition for display]
・A Duplex Unit is installed.
* Sets time to wait for moving to Power Save mode.
Moves to Power Save mode even during an error.
Sets the time to switch from Power Save mode to Sleep
mode.
The start point is the moment when the printer goes into
PowerSave.
*
Set the time to switch from Idle state to Off mode.
*
* Sets display deletion timing of clearable warnings.
PS: JOB only
Sets whether a printer is automatically recovered or not
* when memory overflow/tray request occurs.
(Wait time for recovery: 15 sec)
Sets time to wait for paper to be fed in manual feed.
If paper is not fed within this period of time, the job is
* canceled.
Sets time between stopping reception of job data and
performing force printing.
Does not perform printing and cancels that job instead
in the case of PS.
* "Timeout Local" defaults to 40Sec. and "Timeout
Network" defaults to 90Sec. They can not be changed
through menu settings.
* Sets printer operation when Toner Low is detected.
In CONTINUE, the printer can continue printing while
remaining ON-LINE.
In STOP, it becomes OFF-LINE.
* Sets whether JAM RECOVERY printing is performed or
not when Jam occurs.
When it is set to OFF, a job that includes the page to
which Jam has occurred will be cancelled.
Sets whether an error report is printed or not when an
* internal error occurs.
Valid only for PS、PCL XL and XPS.
−
Prints out data received from the host PC in the
hexadecimal Dump. Turning off the power supply
switch restores Normal Mode from HEX Dump Mode.
If Execute is selected, exit from the menu.
* For the paper fed from MPTray
Adjusts the position of a whole print image in the
direction that is perpendicular to the direction paper
runs, that is horizontally (at 0.25 mm pitch).
Any parts of the print image that go beyond the
printable area as a result of this designation are
clipped.
* For the paper fed from MPTray
Adjust the position of a whole print image in the
direction paper runs, that is vertically (at 0.25mm pitch).
Any parts of the print image that go beyond the
printable area as a result of this designation are
clipped.
機能
Valid
JE
JE
JE
JE
JE
ET
ET
ET
ET
ET
ET
ET
ET
JE
JE
JE
JE
JE
- 70/130