Table of Contents
Advertisement
Quick Links
Specification
Type
Speaker (s)
Full Range
Impedance
Input power (IEC)
Output sound pressure
Frequency range
Dimensions (W x H x D)
CONTENTS
1 way, 1 speaker system
8 cm (3-5/32") cone type (6 Ω)
6 Ω
15 W (Max)
79.05 dB/W (1.0 m)
55 Hz to 25 kHz (-16 dB)
60 Hz to 20 kHz (-10 dB)
127 x 178 x 228 mm
Page
2
2
3
3
4
4
5
SB-NS55P
Colour
(K)... Black Type
Mass
Notes :
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
© 2007 Matsushita Electric Industrial Co. Ltd.. All
rights
reserved.
distribution is a violation of law.
ORDER NO. MD0703019CE
Speaker System
(5" x 7" x 9")
1.4 kg (3.1 lb.)
Page
Unauthorized
copying
and
A6
7
8
9
9
10
11
Advertisement
Table of Contents
Related Manuals for Panasonic SB-NS55P Series
Summary of Contents for Panasonic SB-NS55P Series
-
Page 1: Table Of Contents
ORDER NO. MD0703019CE Speaker System SB-NS55P Colour (K)... Black Type Specification Type 1 way, 1 speaker system (5” x 7” x 9”) Speaker (s) Mass 1.4 kg (3.1 lb.) 8 cm (3-5/32”) cone type (6 Ω) Full Range 6 Ω Impedance Notes : Input power (IEC) -
Page 2: System Combination
SB-NS55P 1 System Combination 1.1. System Breakdown Note : The table below show the breakdown for speaker combinations used in main unit systems. System SC-NS55P-K Music center SA-NS55P-K Speaker system SB-NS55P-K... -
Page 3: Assembling And Disassembling
SB-NS55P 2 Assembling and Disassembling “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. 2. -
Page 4: Disassembly Of Stand Base
SB-NS55P 2.2. Disassembly of Stand base 2.3. Disassembly of Net frame assembly Step 1: Remove 4 screws. Step 1: Upset the speaker cabinet as shown above. Step 2: Insert the flathead screwdriver above the cloth into the groove of speaker cabinet. Step 2: Remove stand base as arrow shown. -
Page 5: Disassembly Of Woofer Unit
SB-NS55P Step 4: Remove net frame unit as arrow shown. Step 2: Insert the steel rule in between the woofer unit and speaker cabinet to push out the woofer unit. Step 5: Remove net frame assembly as arrow shown. 2.4. Disassembly of Woofer unit Follow (step 1) to (step 4) in item 2.3. - Page 6 SB-NS55P Step 4: Remove woofer unit as arrow shown.
-
Page 7: Connection Of The Speaker Cables
SB-NS55P 3 Connection of the Speaker Cables · Be sure to connect speaker cables before connecting the AC power supply cord. · The load impedance of any speaker used with this unit must be 6 Ω. · Be sure to connect the cable from the right speaker to the right terminal and the cable from the left speaker to the left terminal. -
Page 8: Connection Of The Wiring Diagram
SB-NS55P 4 Connection of the Wiring Diagram... -
Page 9: Exploded View
SB-NS55P 5 Exploded view 5.1. Cabinet Parts Location... -
Page 10: Packaging
SB-NS55P 5.2. Packaging... -
Page 11: Replacement Parts List
SB-NS55P 6 Replacement Parts List Notes : · Important safety notice : When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list. · [M] markings in the Remarks columns indicates parts supplied by PAVCSG.
Need help?
Do you have a question about the SB-NS55P Series and is the answer not in the manual?
Questions and answers