Subscribe to Our Youtube Channel
Related Manuals for Evolution S355CPSL
Summary of Contents for Evolution S355CPSL
- Page 1 Original Instructions 5012207 Originally written in UK English Date Published:18/07/2019...
- Page 2 Technical Helpline, the number of which can be found on the Evolution Power Tools website. We operate several Helplines throughout our worldwide organization, but Technical help is also available from your supplier.
- Page 3 www.evolutionpowertools.com Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12...
- Page 4 www.evolutionpowertools.com Fig. 13 Fig. 15 Fig. 14 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 20...
-
Page 5: Specifications
SPECIFICATIONS S355CPSL MACHINE METRIC IMPERIAL Motor (UK/EU) 220V-240V ~ 50Hz Motor (UK) 110V ~ 50Hz Motor (USA) 120V ~ 60Hz Motor (AUS) 240V ~ 50Hz Speed (No Load) @ 110V Speed (No Load) @ 120V 1450 min 1450 rpm... - Page 6 www.evolutionpowertools.com SPECIFICATIONS S355CPS S380CPS * MACHINE METRIC IMPERIAL METRIC IMPERIAL Motor (UK/EU) 220V-240V ~ 50Hz 2200 W Motor (UK) 110V ~ 50Hz 1600 W Motor (USA) 120V ~ 60Hz 15 A Motor (AUS) 240V ~ 50Hz 2200 W Speed (No Load) @ 110V 1550 min 1550 rpm Speed (No Load) @ 120V...
-
Page 7: Polarized Plug
(RCM) Regulatory Compliance Mark for electrical and electronic equipment. LABELS & SYMBOLS (1.8) Australian/New Zealand Standard WARNING: Do not operate this machine if warning and/or instruction labels are missing or damaged. Contact Evolution Power Tools for replacement labels. - Page 8 SAFETY INSTRUCTIONS WARNING: This product has been designed to (These General Power Tool Safety Instructions be used with special Evolution blades. Only use are as specified in EN 62841-1: 2015 & accessories designed for use in this machine EN 62841-3-10:2015.
- Page 9 www.evolutionpowertools.com the influence of drugs, alcohol or medication. A breakage of moving parts and any other moment of inattention while operating power tools condition that may affect the power tools may result in serious personal injury. operation. If damaged, have the power tool b) Use personal protective equipment.
- Page 10 If you lose control, the cord may power tool, it does not assure safe operation. be cut or snagged and your hand or arm may be Use only Evolution carbide tipped blades when cutting woods, metals and plastics or Evolution pulled into the spinning wheel.
-
Page 11: Additional Warnings
www.evolutionpowertools.com a)Maintain a firm grip on the power tool designed. 8. Use the right tool. Don’t force the tool or and position your body and arm to allow you to resist kickback forces. The operator attachment to do a job for which it was can control upward kickback forces, if proper not designed. -
Page 12: Getting Started Unpacking
The serial number can be found on the motor housing of the machine. Hex Key 8mm (Blade Change) For instructions on how to identify the batch code, please contact the Evolution Power V-Block Tools helpline or go to: www.evolutionpowertools.com 100mm blade flange (for fitting 15”... -
Page 13: Machine Overview
S355CPSL MACHINE OVERVIEW LOWER BLADE GUARD 16. CARBON BRUSHES ACCESS CAP UPPER BLADE GUARD 17. ON/OFF TRIGGER SWITCH FRONT SWIVELLING VICE JAW 18. CARRY HANDLE REPOSITIONABLE REAR VICE JAW CUTTING HANDLE CUTTING HEAD HOLD DOWN PIN REAR VICE JAW LOCKING LEVER... - Page 14 www.evolutionpowertools.com S355CPS / S380CPS MACHINE OVERVIEW LOWER BLADE GUARD 16. SHIELD UPPER BLADE GUARD 17. VICE HANDLE QUICK RELEASE MECHANISM 18. CARBON BRUSHES ACCESS CAP FRONT SWIVELLING VICE JAW 19. ON/OFF TRIGGER SWITCH REPOSITIONABLE REAR VICE JAW 20. CARRY HANDLE CUTTING HANDLE 21.
-
Page 15: Transporting The Saw
• Using the Hex Key supplied, loosen the front arbor cover bolt and rotate the arbor cover out Note: The S355CPSL has four mounting of the way. (Fig. 4). holes and S355CPS and S380CPS have three • Press the arbor lock button (labelled) (Fig. 5) mounting holes. - Page 16 Set the rear vice jaw to approximately 45˚ with CHIP COLLECTION the aid of the protractor scale. S355CPSL • Turn the location pin (Fig. 10) ¼ of a turn. A specially shaped steel shield (Fig. 15) This will release the pin and allow the spring...
-
Page 17: Operating Advice
Note: As all operating environments are unique • Ensure that the ‘cut-off’ piece cannot become and diverse, Evolution Power Tools offers the ‘jammed’ in any other part of the machine. following general advice on safe operational • Do not use these saws to cut small pieces. -
Page 18: Maintenance And Adjustments
www.evolutionpowertools.com WARNING: These machines must never be used CUTTING HEAD TRAVEL ADJUSTMENT to cut Asbestos or any material that contains, or is To prevent the blade from contacting any part of suspected to contain, Asbestos. the machines metal base, the downward travel Consult/inform the relevant authorities, and seek of the Cutting Head can be adjusted. -
Page 19: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY The manufacturer of the product covered by this Declaration is: UK: Evolution Power Tools Ltd. Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. FR: Evolution Power Tools SAS. 61 Avenue Lafontaine, 33560, Carbon-Blanc, Bordeaux, France. - Page 20 Total Tools (Importing) Pty Ltd Evolution Power Tools SAS 20 Thackray Road 61 Avenue Lafontaine Port Melbourne 33560, Carbon-Blanc Vic 3207 Bordeaux T: 03 9261 1900 T: +33 (0)5 57 30 61 89 Evolution Power Tools Ltd Evolution Power Tools LLC...
Need help?
Do you have a question about the S355CPSL and is the answer not in the manual?
Questions and answers