HOPEFULL ® electric bed Instruction for use Contents General..............................3 1. Usage and safe notice.......................3 1.1 Usage..........................3 1.2 Safe notice......................... 3 2. Functions introduction and Operation manual...............6 Components name......................6 Bed placement........................6 Functions introduction..................... 7 Main functions operation....................7 Install and operate the bedside rail................9 Install and dismantle the head / foot panels..............
Instruction for use General The instruction is applicable to Hc738a Electric bed. It’s including the information such as usage & safe notice, function instruction, care & maintenance, and so on. The inside pictures are only for reference. When operation, please take the real product for standard.
Page 4
HOPEFULL ® electric bed Instruction for use Don’t put the bed in the wet place, or else the electrical components may be damaged and cause the accident. When the bed without use or move the bed, please take off the plug and wreathe it on the electric wire rack in order to avoid damaging the plug or electric wire.
Page 5
HOPEFULL ® electric bed Instruction for use 6). When move the bed: Please make sure to install and lock well the head and foot panels. If the panels are not locked well before moving the bed, the patient may fall from the bed to get hurt because of the panels loose.
HOPEFULL ® electric bed Instruction for use 2. Functions introduction and Operation manual 2.1 Components name 1. assist belt 2. triangle ring 3. bedside rail 4. foot panel 5. brake 6. castor 7. urine hook 8. socket of lifting pole 9.
® electric bed Instruction for use 2.3 Functions introduction The electric bed Hc738a is designed base on the safe and convenient use, the bed can be operated and adjusted different positions by the controller. The main functions including: 1. Back section up and down adjustment 2.
Page 8
HOPEFULL ® electric bed Instruction for use 1. Back section up and down adjustment Press the the back section up and down buttons, the back bed board can go up and down.Loose the buttons, the back bed board will stop movement .
HOPEFULL ® electric bed Instruction for use 2.5 Install and operate the bedside rail (1)Install the bedside rail 1、Please install the bedside rail at the correct position of the bed frame,and tighten the screws as below pictures. 2、Tighten the screw under the bedside rail,as below picture:...
Page 10
HOPEFULL ® electric bed Instruction for use (2)Operate the bedside rail When patient lies on the bed, please keep the bedside rails risen in order to avoid the patient falling from the bed to cause the accident. When operating, please pay attention whether there is barrier in the gaps between the bedside rails and bed frame, If yes, please eliminate.
HOPEFULL ® electric bed Instruction for use 2.6 Install and dismantle the head / foot panels 1. Install the head / foot panels Release the plastic locks and adjust the both side’s metal pins, then push the panel to fix it,till hearing the sound of “ka”,that means the panel is locked well.
HOPEFULL ® electric bed Instruction for use 2.7 Bed end extension operation 1. Loose “the fixed screw” as below picture. 2. Pull out the extension bed board as below picture.Then tighten the screw when extend to required length. 3. When need to hold the extension bed board, loose “the fixed screw” and push the...
HOPEFULL ® electric bed Instruction for use 2.8 IV drip stand and lifting pole usage 1. Iv drip stand usage (1) Safety working load for IV drip stand is 5 kilogram (2) Firstly insert the IV drip stand into the socket, then lift the inner pipe of IV stand to a desired height, and then fasten the “locked screw”...
HOPEFULL ® electric bed Instruction for use 2.9 Bed movement When there is patient on the bed, please lift up the bedside rails before moving the bed. 1) Release the brake as below picture and then move the bed: 2) Step on the brake as below picture to lock the bed:...
HOPEFULL ® electric bed Instruction for use 2.10 Control box connection methods Wire connection methods: 1. Power supply (Electric source) 2. Hi-low actuator 3. Leg actuator 4. Back actuator 5. Handset socket Notices: If the problems are judged initially from control box,don’t open and repair it by yourself.
HOPEFULL ® electric bed Instruction for use 2.12 Cleaning and disinfection of beds Notices: the products are not applicable to using “Spraying stream” cleaning machines or high pressure and high steam to clean. During the cleaning, do not use the water to sprinkle the beds directly, especially for the electrical parts.
HOPEFULL ® electric bed Instruction for use 2.14 After-sales service contact information Manufacturer: Hopefull Medical Equipment Co., Ltd. Address: The Yangtze Industrial Park, Economic Development Area,Xian'ning City 437100 ,Hubei Province, China. Tel: +86(715) 8898610 Fax: +86(715) 8898613 E-mail: sales01@hope-full.com Website: www.hope-full.com...