Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Pixapro ST-III Plus-N
Summary of Contents for Pixapro ST-III Plus-N
- Page 1 2.4GHz Wireless Flash Trigger ® PIXAPRO LTD. 50 Popes Lane, Oldbury, West Midlands, B69 4PA Tel: 0121 552 3113 Web: www.essentialphoto.co.uk E-mail: info@essentialphoto.co.uk Company Registration No. 07601334 Instruction Manual 705-X2TN00-00 Made In China...
-
Page 2: Table Of Contents
Thanks for your purchase of this ST-III Plus-N wireless flash trigger. Foreword Sync Socket Settings This wireless flash trigger is suitable for using Nikon cameras to control PiXAPRO Warning SHOOT Function Settings flashes with ONE system e.g. camera flash, outdoor flash, and studio flash. It can Names of Parts C.Fn: Setting Custom Functions... -
Page 3: Warning
Warning Names of Parts Body Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Hot Shoe Speedlight Connection Always keep this product dry. Do not use in rain or in damp conditions. AF Assist Beam Switch Keep out of reach of children. -
Page 4: Lcd Panel
Battery Names of Parts AA alkaline batteries are recommended. LCD Panel Installing Batteries As shown in the illustration, slide the battery compartment lid of the flash trigger and insert two V0.2 /128 CH 01 SYNC AA batteries separately. BLUE.T. Battery Indication BEEP Check the battery level indication on the LCD panel ZOOM... -
Page 5: Setting The Flash Trigger
Setting the Flash Trigger Setting the Flash Trigger Power Switch Wireless ID Settings Slide the Power Switch to ON, and the device is on and status indicator lamp will not Change the wireless channels and wireless ID to avoid interference for it can only be reveal. -
Page 6: Output Value Settings
Turn the select dial to For most of camera flashes, the minimum output value is 1/128 and cannot be set to 1/256. However, the value can change to 1/256 when using in combination with PiXAPRO strong power flashes e.g. change the setting value. -
Page 7: Modeling Lamp Settings
Setting the Flash Trigger Setting the Flash Trigger Modeling Lamp Settings Buzz Settings 1. Long press the <MENU> button for 2 seconds to Press the <MENU> button to enter C.Fn BEEP and V0.2 SYNC control the ON/OFF of the modeling lamp. press the <SET>... -
Page 8: Shoot Function Settings
Choose any figure from 01-99 (the old version triggering signals to the slave unit, which is suitable flashes cannot use this function temporarily) Trigger ST-III Plus-N to fire flash PC SYNC Sync cord jack for multi person photography. However, this Output signal to trigger other remote control and flash function consumes power quickly. -
Page 9: Using The Flash Trigger
Setting the Flash Trigger Using the Flash Trigger 1.2 Short press the <MENU> button to set channel, Custom Function Function Setting Signs Settings and Description Zoom STEP Power output 1/128(0.3) The minimum output is 1/128(change in 0.3 step) group, mode and parameters (refers to the value 1/256(0.3) The minimum output is 1/256(change in 0.3 step) -
Page 10: As A Wireless Original Flash Trigger
Using the Flash Trigger Using the Flash Trigger <GR/CH> button to set the same channel to the flash trigger, and short press 4. As a Wireless Studio Flash Trigger Take LUMI 400II as an example: the < GR/CH> button to set the same group to the flash trigger (Note: please refer to the relevant instruction manual when setting the oudoor flashes of other 4.1 Turn off the camera and mount the transmitter models). -
Page 11: As A Wireless Shutter Release Trigger
Using the Flash Trigger Using the Flash Trigger 5. As a Wireless Shutter Release Trigger 6. As a Flash Trigger with 3.5mm Sync Cord Jack Operation method: Operation method: 5.1 Turn off the camera. Take a camera remote 6.1 The connection method please refers to the cable and insert one end into the camera’s contents of “As a Wireless Studio Flash Trigger”... -
Page 12: Compatible Smartphone Models
Compatible Smartphone Models Using the Flash Trigger This flash trigger can be used on the following Smartphone models: 7.5 Full match and back to APP main interface. iPhone 6S iPhone 6S Plus iPhone 7 Plus iPhone 7 iPhone 8 Plus 7.6 When started the Bluetooth function, the Bluetooth icon will be displayed on the iPhone 8... -
Page 13: Compatible Flash Models
2.4GHz Li-ion580 Manual D750 D810 D610 D600 D800 D800E D700 D300S Note: The range of support functions: the functions that are both owned by ST-III Plus-N and flash. D300 D7500 D7200 D7100 D7000 D5600 D5500 D5300 D5200 D5100 D5000 D3400... -
Page 14: Technical Data
Firmware upgrade Upgrade through the Type-C USB port USB socket, please use Type-C USB connection line. As the firmware upgrade needs the support of PiXAPRO G3 software, please Memory function Settings will be stored 2 seconds after last operation and recover after a restart download and install the "PiXAPRO G3 firmware upgrade software"... -
Page 15: Attentions
Operating distance limited or flash missing. Check if batteries are exhausted. If so, change them. The Reason & Solution of Not Triggering in PiXAPRO 2.4G Wireless Disturbed by the 2.4G signal in outer environment (e.g. wireless base Caring for Flash Trigger station, 2.4G wifi router, Bluetooth, etc.) - Page 16 FCC Statement A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the ST-III Plus-N and is the answer not in the manual?
Questions and answers