Tool Holder - Shop-Vac 86S User Manual

CASTER SySTEM ASSEMBLy
Not all units are equipped with the same caster system. Follow the instructions, which
apply to your specific unit.
Without Caster feet
you will find four casters (figure 1) with your wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that bottom is facing up.
2. Insert casters into bottom of tank by placing stem of
caster into holes provided. Apply pressure and twist-
ing motion until casters snap into place (figure 2).
3. Return tank to upright position.
5-8 U.S. Gallons (18.9 - 30.2L) With Caster feet
you will find four caster feet (figure 3), four casters (figure 4), and four
screws with your wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn
tank upside down so that bottom is facing up.
2. Remove any webbing that attaches the caster feet to each other.
3. With front of tank inlet facing you, take caster feet marked with the letter
A (figure 5) and insert stem of caster foot into holes on left front and
right rear of tank also marked with letter A (figure 6). make sure caster
feet are fully inserted into tank bottom and secure with screws provided
(figure 7).
4. Take caster feet marked with the letter B (figure 8) and insert stem of
caster foot into holes on right front and left rear of tank also marked
with the letter B (figure 9). make sure caster feet are fully inserted into
tank bottom and secure with screws provided (figure 10).
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (figure 11).
6. Return tank to upright position.
5
8 9
B
B
B
A
10 U.S. Gallons (37.8L) and Up With Caster feet
you will find four caster feet, four casters and four screws (figure 12) with your wet/dry vacuum.
Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that bottom is facing up.
2. With front of tank facing you, take caster feet marked with the letter A (figure 13) and place
in slots on left front and right rear of tank also marked with the letter A (figure 14). Secure
with screws provided (figure 15).
3. Take caster feet marked with the letter B (figure 16) and place in slots on right front and left
rear of tank also marked with the letter B (figure 17). Secure with screws provided (figure
18).
4. If flat washers are included in hardware package place flat washer over stem of caster before
installing casters into feet. NOTE: flat washers are not required with all units.
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (figure 19). Return tank to upright position.
12 13
A
16 17
B
B
A
B
With Rear Caster Dolly/Tool Holder
you will find four casters (figure 20), two caster feet (figure 21), rear caster dolly/tool holder
(figure 22), and four screws with your wet/dry vacuum. Assemble as follows:
20
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that the bottom is facing up.
2. Take rear caster dolly and place into slots (on rear of tank, opposite of drain) and secure with
screws provided (figure 23).
3. If flat washers are included in hardware package place flat washer over stem of caster before
installing casters into feet. NOTE : flat washers are not required with all units.
1
6 7
A
B
A
10
11
A
B
B
B
14 15
A A
A
A
A
18 19
A
B
B
B
21 22
4. Insert casters into bottom of rear caster dolly by placing stem of caster into holes provided.
Apply pressure and twisting motion until casters snap into place (figure 24).
5. With tank drain facing you, take caster foot marked with the letter A (figure 25) and place
in slot on left side of tank also marked with the letter A. Secure with screw provided (figure
26).
6. Take caster foot marked with the letter B (figure 27) and place in slot on right side of tank
also marked with the letter B. Secure with screw provided (figure 28).
7. Insert casters into feet by placing stem of casters into holes provided. Apply pressure and
2
twisting motion until casters snap into place (figure 29).
8. Return tank to upright position.
9. Place tool basket (not standard with all models) with curved surface against tank on rear
caster dolly assembly (figure 30).
3
4
(Not standard with all models)
1. With rear of unit facing you, take tool holder and position it with tabs facing rear of unit
(figure 31).
2. Place "J" shaped tabs into the slots on cord wraps (figure 32).
3. Press down until tabs snap into place.
4. Press down on center of tool holder until tab latches on bottom of lid (figure 33).
INSTALLING fOAM SLEEVE AND REUSABLE
(Not standard with all models)
WARNING
THE WALL OUTLET BEfORE REMOVING THE TANk COVER.
When using the reusable dry filter to pick-up dust and dry
material, you must install foam sleeve and reusable dry
filter to ensure proper filtration. If the vacuum has been
used to pick-up liquids, the foam sleeve must be cleaned
and dried before installing for dry pick-up. With tank cover
in an upside down position, slide foam sleeve down over lid
cage pulling until foam sleeve completely covers lid cage
(figure 34). NOTE: Bottom of foam sleeve must be posi-
tioned on the OuTSIde of groove around lid cage for the
reusable dry filter to fit properly (figure 35, 36). Center the
reusable dry filter on lid cage (figure 37), slide mounting
ring down over filter until ring is positioned against the ribs
of the lid cage (figure 38). The reusable dry filter should
always be in position over the foam sleeve for dry pick-up.
To remove the filter for cleaning, remove mounting ring and
B
filter from lid cage (figure 39). To clean the reusable dry
filter, shake off excess dirt and dust or (depending on the condition of the filter) rinse with water.
Allow the filter to dry completely and re-install. dO NOT mACHINe WASH OR dRy.
INSTALLING THE CARTRIDGE fILTER
(Not standard with all models)
NOTE: If foam sleeve is in position over lid cage, it does not
need to be removed before installing cartridge. foam must
be positioned on the INSIde of groove around lid cage for
cartridge to fit properly.
The cartridge filter can be used for wet or dry pick-up; instal-
lation is the same for both. When picking up large quantities
of liquid please refer to the Wet Pick-up Operation section in
this manual. use the cartridge filter in position over the lid
cage for most general dry material pick-up. With the tank
cover in an upside down position, slide the cartridge filter
down over the lid cage, pushing until the filter seals against
the cover (figure 40). Place filter retainer into the top of the
cartridge filter, hold the tank cover with one hand, turn the
handle on the filter retainer clockwise to tighten, locking the
filter into place (figures 41 & 42). To remove the filter for
24 25
23
27 28 29
A
B
B
A

TOOL HOLDER

31 32 33
DRy PICk-UP
DRy fILTER
– ALWAyS DISCONNECT THE PLUG fROM
26
A
A
30
34 35
36
37
38 39
40 41
42 43
TIGHTEN LOOSEN
44
46
45