5-10. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 M30622MGA-A39FP (SYSTEM CONTROLLER)
Pin No.
Pin Name
1
AMP-DATA
2
AMP-CLK
3
AMP-LAT
4
SIRCS
5
DIG-TX
6
DSP-RX
7
DIG-CLK
8
GND
9
CNVSS
10
XCIN
11
XCOUT
12
RESET
13
XOUT
14
VSS
15
XIN
16
VCC
17
NMI
18
RDS-INT
19
—
20
RDS-DATA
21
ST-MUTE
22
ST-CE
23
ST-DOUT
24
—
25
ST-DIN
26
—
27
ST-CLK
28
—
29
IIC CLK
30
IIC DATA
31 to 34
NO-USE
35 to 40
—
41
M-RESET
42 to 50
—
51
NO-USE
52 to 57
—
58
EXP-IN DATA
59
EXP-OUT DATA
60
EXP-LAT
61
EXP-CLK
62
VCC
63
SOFT-TEST
I/O
O
Serial data output to the M61512FP (IC607)
O
Serial data transfer clock signal output to the M61512FP (IC607)
O
Serial data latch pulse signal output to the M61512FP (IC607)
I
Remote control signal input from the remote control receiver (IC101)
Serial data output to the CXD9617R (IC601), digital audio interface receiver (IC604) and digital
O
filter (IC606)
I
Serial data input from the digital audio interface receiver (IC604)
Serial data transfer clock signal output to the CXD9617R (IC601), digital audio interface receiver
O
(IC604) and digital filter (IC606)
—
Ground terminal
—
Not used
I
Sub system clock input terminal (32.768 kHz)
O
Sub system clock output terminal (32.768 kHz)
System reset signal input from the reset signal generator (IC551) "L": reset
I
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
O
Main system clock output terminal (16 MHz)
—
Ground terminal
I
Main system clock input terminal (16 MHz)
—
Power supply terminal (+5V)
I
Non-maskable interrupt input terminal Fixed at "H" in this set
I
Serial data transfer clock signal from the RDS decoder on the FM/AM tuner unit
—
Not used (open)
I
Serial data input from the RDS decoder on the FM/AM tuner unit
O
Tuner muting on/off control signal output to the FM/AM tuner unit "L": muting on
O
Chip enable signal output to the FM/AM tuner unit
O
Serial data output to the FM/AM tuner unit
—
Not used (open)
I
Serial data input from the FM/AM tuner unit
—
Not used (open)
O
Serial data transfer clock signal output to the FM/AM tuner unit
—
Not used (open)
Communication data reading clock signal input or transfer clock signal output with the display
I/O
controller (IC601) and CDP-S3
I/O
Communication data bus with the display controller (IC601) and CDP-S3
—
Not used
—
Not used (open)
O
Reset signal output to the display controller (IC601) "L": reset
—
Not used (open)
—
Not used
—
Not used (open)
I
Serial data input from the I/O expander in the TA-S7AV
O
Serial data output to the I/O expander in the TA-S7AV
O
Serial data latch pulse signal output to the I/O expander in the TA-S7AV
O
Serial data transfer clock signal output to the I/O expander in the TA-S7AV
—
Power supply terminal (+5V)
I
Soft test output terminal Not used (open)
Description
ST-S5
21