Beko L6B PDP TV Service Manual page 10

Turning On the Plasma Display
You can only control your plasma display with the
remote control when the device is in stand-by mode.
Switch the mains switch in the input panel into Position I.
The operational display on the front side of the display
screen lights up red.
• Press a numeric button or the Program
Up / Program Down button on the
remote handset or PR+ / PR- or MENU
button on the front panel of the TV to
switch the TV on. The standby indicator
turns into green. The picture will appear
after a few seconds.
Press the Standby button to switch the
TV to standby. The standby indicator turns
into red.
• The plasma display is always connected to the
power supply network in stand-by mode. You must
switch the mains switch into position 0 and pull the
mains plug from the socket for complete disconnection.
• Display has a mains adapter, and can be operated
with a supply voltage of 230V AC and 50HZ.
Note 1: Your TV will go to stand-by mode in five
minutes if there is no broadcast signal.
Note 2: Your TV is equiped to operate with front
panel buttons, "MENU", "SOURCE", "
" VOL " in case your R/C is broken or the
batteries are exhausted.
The batteries
Remove the back cover to reveal the battery
compartment and make sure you insert the batteries
the right way round.
Suitable battery types for this remote are UM-4, IEC
R03 or AAA 1.5V.
Do not combine a used, old battery with a new one
or mix battery types.
The performance of the remote control will deteriorate
beyond a distance of 8 metres or outside an angel
of 30 degrees from the centre of the TV.
Operating Modes
Operating mode at the beginning of utilisation
Due to the functionality of the Plasma-TV please pay
attention, that particularly during the first 100 to 150
operation hours the display has to operate with a full
screen format adjustment (see submenu Display, Picture
Format). This prevents the formation of brightness
differences in the display areas. As an alternative to
the picture format 4:3 the adjustment Video NLS should
be selected.
Further on, in order to prevent the formation of permanent
shadows in the displayed image, please avoid to show
fixed-images of any kind (PC mode, teletext pages,
Photo CD image etc.) during the first operation hours.
If the Plasma-TV will be used as a PC monitor, the
utilisation of a screensaver is recommended.
PC mode
For optimal image reproduction, we recommend the
848 x 480, 640 x 480 or 720 x 400 pixel resolutions.
The 848 x 480 pixel resolution corresponds to the
display matrix, and offers the best image reproduction.
You can obtain the driver for this resolution on the
Internet pages of mont of the well-know manufacturers
of graphics cards.
PROG ",
In contrast to applications with CRT monitors, with flat
displays it is not necessary to select a high image
refresh for a flicker-free presentation. A refresh of
60Hz is recommended.
Video recorder mode
The utilisation of Y/C (S-Video) inputs is recommended
for enhancement of image quality - if your recorder
offers playback in Y/C (S-Video) format.
DVD player mode
The application of the RGB operating mode, which
can be connected to the SCART 1 input, is
recommended for optimal utilisation. In case your
player does not offer this operating mode, please use
the Y/C (S Video) signal mode.
Image sticking
The manufacturer would like to point out to you that
during lengthy viewing of freeze pictures (e.g. PC
playback), the image is still slightly visible in the full
mask for a few minutes during the subsequent playback
of a different source. This is known as "image sticking"
This "vanishing" residual image is caused by the
system, and does not represent a flaw. Therefore it
can not be considered as a case for warranty claim.
Video cable
A high-quality 75Ω coaxial cable should be utilised
for the connection of the video signal. Poor quality
signal cable can result in strong disturbances and
formation of shadows in the displayed image, as well
as exceeding the permissible EMC level. The
mechanical interlocks of the individual plug-and-socket
connectors are necessary for perfect and safe operation
of the device.