Related Manuals for Fanimation Kubix FP4420 Series
Summary of Contents for Fanimation Kubix FP4420 Series
-
Page 1: Ceiling Fan
The Kubix ™ Ceiling Fan Net Weight 10.21 kg (22.5 lbs) Model No. FP4420** OWNER’S MANUAL READ AND SAVE THESE INSTRUCTIONS... -
Page 2: Table Of Contents
Fanimation. 7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty. 8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac- company authorized returns and must be sent freight prepaid to Fanimation. -
Page 3: Tools Needed For Assembly
Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. -
Page 4: Energy Effi Cient Use Of Ceiling Fans
If ceiling height allows, install the fan 8 - 9 feet above the floor for optimal airflow. Consult your Fanimation Retailer for optional mounting accessories. Turn Off When Not in the Room Ceiling fans cool people, not rooms. If the room is unoccupied, turn off the ceiling fan to save energy. -
Page 5: How To Assemble Your Ceiling Fan
How to Assemble Your Ceiling Fan 1. Remove the Hanger Ball by loosening the setscrew in the Hanger Ball until the ball falls freely down the Downrod. (Figure 1) Remove the Pin from the Downrod, then remove the Hanger Ball. Retain the Pin and Hanger Ball for reinstallation in Step 4 (Figure 4). -
Page 6: Fan Alignment And Hanger Bracket Installation
Fan Alignment And Hanger Bracket Installation ▲WARNING Failure to follow these Hanger Bracket installation procedures may result in damage to Hanger Bracket. 1. Preliminary Hanger Bracket Attachment (Figure 1): Drill ¼˝ pilot hole through the center of the junction box, into the ceiling joist or structural member. -
Page 7: Final Fan Assembly
CAUTION The fan must be hung with at least 7´ of clearance from floor to blades (Figure 1) 1. Make sure the electrical supply wires, including the hanger bracket grounding wire and safety cable are pulled through the extension pole, between the hanger bracket and the junction box so that electrical connections can be made later. -
Page 8: How To Wire Your Ceiling Fan - C24 Remote Control
How to Wire Your Ceiling Fan - C24 Remote Control If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. ▲WARNING To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. -
Page 9: Installing The Downrod Cover Clip
Installing the Downrod Cover Clip 1. After hanging the fan, slide the Square Motor Coupling Cover and Square Sleeve upward to install the Downrod Cover Clip. (Figure 1) NOTE: The clip must be properly installed as described in Step 1, or square sleeve will not seat properly. 2. -
Page 10: Installing The Lower Housing Light Kit Assembly
Installing the Lower Housing Light Kit Assembly CAUTION To avoid possible electrical shock, be sure electricity is turned off before installing downlight assembly. 1. Loosen three screws and remove one screw from support flange. (Figure 1). 2. Securely attach the Lower Housing Assembly to the Support bracket and tightening four screws. - Page 11 Installing the Lower Housing Light Kit Assembly (cont’d) 5. Install two Candelabra Bulbs (not included - 60 watts max) in each of the sockets on the Downlight Socket Plate Assembly. (Figure 5) IMPORTANT 60 watt bulbs are the maximum wattage allowed to safely operate the fan.
-
Page 12: Operating Instructions - C24 Remote Control
Operating Instructions - C24 Remote Control ▲WARNING Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until the blades is in place. Noise and fan damage could result. -
Page 13: Trouble Shooting
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections in the switch housing. 1. -
Page 14: Parts List
Before discarding packaging materials, be certain all parts have been removed Contact your retail store for repair parts. When ordering repair parts, always give the following information. Parts List Model #FP4420** Description How To Order Parts • Part Number • Part Description •... -
Page 15: Exploded-View Illustration
™ The Kubix FP4420** Exploded-View NOTE: The illustration shown is not to scale or its actual confi guration may vary Reversing Switch Figure 1... - Page 16 10983 Bennett Parkway Zionsville, IN 46077 (888) 567-2055 FAX (866) 482-5215 Outside U.S. call (317) 733-4113 Visit Our Website www.fanimation.com Copyright 2008 Fanimation 2008/02...