Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d'installer et d'utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main
pour toute référence ultérieure.
VCC-4374P
Advertisement
Table of Contents
Related Manuals for Sanyo VCC-4374P
Summary of Contents for Sanyo VCC-4374P
- Page 1 INSTRUCTION MANUAL VCC-4374P BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR About this manual A propos de ce manuel Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce manual carefully. Be sure to keep it handy for later reference.
-
Page 2: Table Of Contents
Depending on the conditions of use, installation and environment, FEATURES please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. • The optical filter is switched automatically to colour image or black and white image according to the subject brightness. -
Page 3: Precautions
Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. -
Page 4: Parts Names
PARTS NAMES Power indicator (POWER) Comes on when the power to the camera is on. Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. NC + – Manual colour/black and white setting terminal (CONTROL) ... - Page 5 PARTS NAMES Flange-back lock screw Flange-back adjustment lever (See page 6) Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings.
-
Page 6: Concerning Auto-Iris Lenses
ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the A.I. LENS switch to the VIDEO position.) Compatible auto-iris lenses 1/3 inch Sanyo DC type lens VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm... -
Page 7: Flange-Back Adjustment
FLANGE-BACK ADJUSTMENT If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. -
Page 8: Mounting The Lens
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “L” is more than 5 mm. If not, that may damage the camera and prevent proper installation. Remove the lens mount cap from the camera. - Page 9 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.
-
Page 10: Connections
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. Use a commercially available 24 V AC adaptor Connect an AC 24 V power source to the 24 V AC connectors on the back of the camera. -
Page 11: Settings
SETTINGS Camera setup section High speed electronic shutter setting e f g Normally, the speed setting switches Table A for the high speed electronic shutter 1/50 sec. C-BW are all set to the OFF position. This VR301 LEVEL sets the electronic shutter speed to 1/120 sec. - Page 12 SETTINGS White balance adjustment Backlight compensation setting Normally the WB (white balance) switch is set Use an auto-iris lens and set the EI/BLC switch to the A (automatic) position and the white to the BLC-ON position, to engage the balance is adjusted automatically. If a manual backlight compensation function.
- Page 13 SETTINGS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the When using an auto-iris lens (for indoor/outdoor shortest F stop. Set the EI/BLC switch to the EI-ON position. use) Set the EI/BLC switch to the OFF position. CAUTION: If conditions are outside the electronic iris operation range or more than the maximum illumination, it will cause saturation of the CCD.
- Page 14 SETTINGS C • B/W (colour/black and white) switch setting Manual colour/black and white setting This switch lets you select the timing of the automatic switching of Connect each pin of the CONTROL terminal as indicated below, to the optical filter to colour image or black and white image, according set the image to black and white or colour as desired.
-
Page 15: Troubleshooting
If it still does not perform correctly, Set the SYNC switch to the L-L position. please consult your dealer or a Sanyo Authorized Service Centre. When using a camera switcher to connect 2 No picture on the monitor screen cameras or more to one monitor, there may be •... -
Page 16: Specifications
Electronic shutter : 8 speeds, selectable by switches: the cabinet. Servicing should always be referred to your dealer or (1/50, 1/120, 1/250, 1/500, 1/1000, Sanyo Authorized Service Centre. 1/2000, 1/4000, 1/10000 sec.) Backlight compensation : Manual ON/OFF switching, Multi-zone light measuring system... - Page 17 SPECIFICATIONS Dimensions: mm 126.5 1/4”–20 UNC 15.4 25.2 Features and specifications are subject to change without prior notice or obligations. English...
- Page 18 Sanyo Electric Co, Ltd. 1AC6P1P2187-- Printed in Japan L53U4/XE(1299KP-NI)