Download
Share
Print this page
Sanyo VCC-4115P Instruction Manual
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Security Camera
  5. VCC-4115P
  6. Instruction manual
Sanyo VCC-4115P Instruction Manual

Sanyo VCC-4115P Instruction Manual

Colour ccd camera
Hide thumbs

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d'installer et d'utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main pour
toute référence ultérieure.
VCC-4115P

Advertisement

loading
Need help?

Need help?

Do you have a question about the VCC-4115P and is the answer not in the manual?

Questions and answers

Related Manuals for Sanyo VCC-4115P

Summary of Contents for Sanyo VCC-4115P

  • Page 1 Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der Kamera zuerst diese Bedienungsanleitung sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. VCC-4115P A propos de ce manuel Avant d’installer et d’utiliser la caméra, veuillez lire ce manuel attentivement. Gardez-le à portée de main pour...

  • Page 2: Table Of Contents

    Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS PRECAUTIONS ... 2 PARTS NAMES ... 3 MOUNTING THE LENS ... 5 CONNECTIONS...

  • Page 3: Precautions

    If water or a liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Be careful to protect the camera from rain, sea water, etc.

  • Page 4: Parts Names

    PARTS NAMES Flange-back lock screw (LOCK) Flange-back adjustment dial Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings.
  • Page 5 PARTS NAMES Camera setup section White balance adjustment volume (R or B) Line phase adjustment volume (PHASE) Lens iris adjustment volume Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.

  • Page 6: Mounting The Lens

    MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Check the lens mount Do not use a lens if the length “L” is more than 5 mm. That may damage the camera and prevent proper installation. C mount type lens Remove the lens mount cap from the camera.
  • Page 7 MOUNTING THE LENS I I I I Pin layout I I I I Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below.

  • Page 8: Connections

    CONNECTIONS (Video signal connections) : VIDEO IN : VIDEO OUT Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.), AC adaptor and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. Connect the power supply.

  • Page 9: Settings

    SETTINGS I I I I Camera setup section Settings Electronic Iris (EI)/Auto iris (AI) setting Aperture compensation setting • SHRP (sharp)/NORM (normal) Backlight compensation mode setting (BLC) • MULTI (Multi)/OFF Backlight compensation mode setting (BLC) • CENT (Center)/OFF White balance setting •...
  • Page 10 SETTINGS I I I I Iris function setting 1 This should normally be set to the down (AI) position. Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the switch to the up (EI) position. Note: Please refer to the specifications for dynamic range of the electronic iris.
  • Page 11 SETTINGS I I I I Backlight compensation setting 3 4 This camera has two different backlight correction functions: multi-spot photometry (MULTI) and center focus photometry (CENT). The normal setting (switch ) is the down position, but you can change the switch setting in accordance with the backlight conditions.
  • Page 12 SETTINGS I I I I White balance adjustment 5 Normally the switch is set to the down (ATW: auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the switch to the up (MANU) position, then adjust the colour.
  • Page 13 SETTINGS I I I I Lens iris adjustment 7 If using a DC type auto-iris lens, you will need to set the LEVEL volume when shooting in the conditions described below. LEVEL L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast •...

  • Page 14: Troubleshooting

    Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. I I I I No picture on the monitor screen •...

  • Page 15: Specifications

    However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre. English...
  • Page 16 SPECIFICATIONS I I I I Dimensions 25.8 Features and specifications are subject to change without prior notice or obligations. English 10.7...