Download
Share
Print this page
Land Pride 3P1006NT Operator's Manual
  1. Manuals
  2. Brands
  3. Land Pride Manuals
  4. Farm Equipment
  5. 3P1006NT
  6. Operator's manual

Land Pride 3P1006NT Operator's Manual

Compact drill
Hide thumbs

Advertisement

Quick Links

Download this manual
Compact Drill
3P1006NT
Table of Contents
Read the Operator's Manual entirely. When you see this symbol,
the subsequent instructions and warnings are serious - follow
without exception. Your life and the lives of others depend on it!
Cover photo may show optional equipment not supplied
with standard unit.
For an Operator's Manual and Decal Kit in another
language, please see your Land Pride dealer.
32685
313-521M
Operator Manual
Printed 2019-07-18

Advertisement

loading

Related Manuals for Land Pride 3P1006NT

Summary of Contents for Land Pride 3P1006NT

  • Page 1 Your life and the lives of others depend on it! Cover photo may show optional equipment not supplied with standard unit. For an Operator’s Manual and Decal Kit in another language, please see your Land Pride dealer. Printed 2019-07-18...
  • Page 2 Machine Identification Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new manual. If you or the dealer have added options not originally ordered with the machine, or removed options that were originally ordered, the weights and measurements are no longer accurate for your machine.
  • Page 3 Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
  • Page 4 Parts Manual for this equipment. for Land Pride products. Download the appropriate App on your Refer to Parts Manual QR smart phone, open the App, point your Locator on this page for phone on the QR code and take a picture.
  • Page 5 Be Familiar with Safety Decals  Read and understand “Safety Decals” on page 5, thoroughly.  Read all instructions noted on the decals.  Keep decals clean. Replace damaged, faded and illegible decals. 2019-07-18 3P1006NT 313-521M...
  • Page 6 Keep Riders Off Machinery Riders obstruct the operator’s view. Riders could be struck by foreign objects or thrown from the machine.  Never allow children to operate equipment.  Keep all bystanders away from machine during operation. 3P1006NT 313-521M 2019-07-18...
  • Page 7  When inflating tires, use a clip-on chuck and extension hose long enough for you to stand to one side–not in front of or over tire assembly. Use a safety cage if available.  When removing and installing wheels, use wheel-handling equipment adequate for weight involved. 2019-07-18 3P1006NT 313-521M...
  • Page 8  Do not stand between the moving tractor and drill during hitching.  Keep hands, feet and clothing away from power-driven parts.  Wear snug-fitting clothing to avoid entanglement with moving parts.  Make sure all persons are clear of working area. 3P1006NT 313-521M 2019-07-18...
  • Page 9 1 total See “Transporting” on page 23. Reflectors: Red 32686A 838-266C On rear face of lift assist cross tube, outside daytime reflectors; On rear face of walkboard, outside daytime reflectors; 4 total See “Transporting” on page 23. 2019-07-18 3P1006NT 313-521M...
  • Page 10 Danger: Moving Chain (Option) 32763 818-518C CAUTION MOVING CHAIN HAZARD To prevent serious injury from moving chain: DO NOT operate with enclosure missing 818-518C Dual Seed: On outside of box end wall, under both covers; 2 total 3P1006NT 313-521M 2019-07-18...
  • Page 11 On front faces of both lower 3-point hitch arms; 2 total 32686 See “Hitching Tractor to Drill” on page 15. Danger: Possible Chemical Hazard 838-467C Under lid of Small Seeds box; 1 total 32761 See “Loading Materials” on page 25. 2019-07-18 3P1006NT 313-521M...
  • Page 12 On front face of right 3-point hitch arm; 1 total 32686 See “Hitching Tractor to Drill” on page 15. Warning: Falling Hazard 838-102C On left side frame at ladder; 32686 2 total See “Loading Materials” on page 25. 3P1006NT 313-521M 2019-07-18...
  • Page 13 Native Grass: Under lid; 2 under lid 2, 3, 4, or 5 total See “Hitching Tractor to Drill” on page 15. Warning: Moving Parts 818-860C On front face of upper front cross tube at gearbox; 1 total 32686 2019-07-18 3P1006NT 313-521M...
  • Page 14 TO PREVENT POSSIBLE EQUIPMENT DAMAGE: THE TRANSPORT LOCKS ARE TO BE USED ONLY FOR LOADING/UNLOADING ON TRAILERS. USING THEM IN OTHER SITUATIONS COULD LEAD TO LIMITED MANUVERABILITY IN TRANSPORTATION. 848-339C On top face of caster cross tube; 2 total 3P1006NT 313-521M 2019-07-18...
  • Page 15 Table of Contents Important Safety Information NOTICE: Petroleum Products 858-679C On ends of seed boxes; 1 per seed box 28214B 2019-07-18 3P1006NT 313-521M...
  • Page 16 Table of Contents Introduction Introduction Land Pride welcomes you to its growing family of new product owners. Your Semi-Mounted 10-Foot No-Till Drill has been designed with care and built by skilled workers using quality materials. Proper setup, maintenance, and safe operating practices will help you get years of satisfactory use from the machine.
  • Page 17 2. If you are still unsatisfied, seek out the owner or gen- eral manager of the dealership, explain the problem, and request assistance. For further assistance write to: PO Box 5060 Salina, KS 67402-5060 2019-07-18 3P1006NT 313-521M...
  • Page 18 5. Check that all safety decals and reflectors are correctly located and legible. Replace if damaged. See “Safety Decals” on page 5. 6. Inflate tires to pressure recommended and tighten wheel bolts as specified. See “Appendix A - Reference Information” on page 58. 3P1006NT 313-521M 2019-07-18...
  • Page 19 Table of Contents Preparation and Setup Hitching Tractor to Drill The 3P1006NT is a Semi-Mounted 3-Point Category II hitch implement. Heavy Falling Object Hazard: Hitch Extension Never mount an extension hitch or setback kit by itself on the If no hitch extension is required, skip to step 4.
  • Page 20 Hydraulic Hose Hookup Connect hydraulic system to tractor before lifting the drill. High Pressure Fluid Hazard: The hydraulic system of the 3P1006NT drill has one Escaping fluid under pressure can have sufficient pressure to single-acting lift-assist cylinder. The cylinder raises the penetrate the skin.
  • Page 21 This is the factory configuration. Note: The drive wheel axle height may need to be adjusted due to ground conditions. See page 32. 15. Check level of frame front-to-rear. If not level, adjust the rear height with the stroke control spacers. 2019-07-18 3P1006NT 313-521M...
  • Page 22 25 mm 32 mm 38 mm 44 mm 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 2.75 3.00 3.25 3.25 3.50 3.75 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50 Figure 7 32057 6.50 Stroke Control Spacers 28359 3P1006NT 313-521M 2019-07-18...
  • Page 23 8. Check that the caster pivots are unlocked. Falling hazard: Watch your step when walking on drill ladder and walkboard. Falling from drill could cause severe injury or death. 2019-07-18 3P1006NT 313-521M...
  • Page 24 Secure with pin. 8. Start tractor. Figure 9 32057 9. Slowly move the lift circuit lever to Retract, allowing Stroke Control Spacers the cylinder to settle on the lock (and relieving pressure from the hydraulic system). 3P1006NT 313-521M 2019-07-18...
  • Page 25 2. Lower the tractor 3-point lift arms to the stop, block or reference indicator established at step 15 on page 17. 3. Move lift-assist circuit lever to Float. 4. If about to begin planting, set tractor 3-point hitch to Float (and not Draft or Depth Control mode). 2019-07-18 3P1006NT 313-521M...
  • Page 26 3. Lift lock pins out of lock plate holes and turn 90 degrees to hold in the unlock position. Figure 10 32058 Caster Pivot Locked 3P1006NT 313-521M 2019-07-18...
  • Page 27 Heavier mix components settle to the bottom, which can Observe Road Rules prevent drive system from operating, and results in irregular Comply with all national, regional and local safety laws seed rate and population distribution. when traveling on public roads. 2019-07-18 3P1006NT 313-521M...
  • Page 28 Table of Contents Operating Instructions Typical 3P1006NT Weights by Configuration Standard Drill Drill with Drill with NG Drill with SGS Drill with Drill with Option (40) Fertilizer (Native Grass) (Small Seeds) Fert. and SGS NG and SGS All Boxes Empty...
  • Page 29 5. To reduce wear, remove main shaft drive chains for 4. Load fertilizer evenly into fertilizer compartment. main seed boxes. 5. To reduce wear, remove drive chains for seed boxes not used. Loading Dual Seed Box See “Main Seed Box Loading.” 2019-07-18 3P1006NT 313-521M...
  • Page 30 Rather than increase the coulter depth, you can increase opener down force at the row unit springs. Never back up with openers in the ground. To do so may cause damage or opener plugging. 3P1006NT 313-521M 2019-07-18...
  • Page 31 Meter Style and Manual Figure 13 34776 194-074M 152-314M 34937 Acremeters 27378 152-325M 194-209M 36275 1. An electronic acremeter is available as an upgrade for older no-till drills having a mechanical acremeter. 2019-07-18 3P1006NT 313-521M...
  • Page 32 18. Use spray paint to cover scratches, chips and worn 5. Disconnect lighting harness and any other electrical areas on the drill to protect the metal. connections. 19. Cover with a tarp if stored outside. 6. Disconnect lift-assist hydraulic line. 3P1006NT 313-521M 2019-07-18...
  • Page 33 Dual Box Seed rate is controlled by adjustments for: provide adjustments for optimal field results. • Right Drive Type gearbox lever The 3P1006NT has double-disc 06 Series openers with • Seed Rate Handle at box (drill rear) depth-controlling press wheels mounted on floating •...
  • Page 34 See “Coulter Down Pressure” on page 31. Set both left and right ground drive axles identically. Figure 15 18509 Coulter Depth Adjustment Normal practice is to set coulter depth approximately 1 inch deeper than desired seed depth. 3P1006NT 313-521M 2019-07-18...
  • Page 35 Drill w/Small Seed 178 lbs (81 kg) 256 lbs (116 kg) 3P1006NT configurations typically are too light to reach Fert. & Small Seed 200 lbs (91 kg) 278 lbs (126 kg) the factory down-force of 400 lbs at all rows. The table at NG &...
  • Page 36 The kit includes two brackets. Each bracket accepts up to five 100 pound (45 kg) weights. The following table shows the additional force per row that the kit can provide. Weights Additional Force per Row Added Pounds Kilograms Figure 18 28364 Adding Weights 32800C 3P1006NT 313-521M 2019-07-18...
  • Page 37 [except Fertilizer and ® Seed-Lok ] supported for use with the 3P1006NT drill; coulter is not part of opener assembly and is not shown) From front to back, a 06 Series row unit can include the following capabilities (some optional): 1.
  • Page 38 3. To reduce the spacing between the discs (the normal case), move one spacer washer from the inside to the outside of the disc. Figure 21 26385 4. Re-assemble and check disc contact. Adjusting Disc Spacers 3P1006NT 313-521M 2019-07-18...
  • Page 39 Refer to Figure 23 To adjust scrapers, loosen inch bolt and move scraper as needed. The standard scraper is shown. Optional spring-loaded carbide scrapers are available (see page 53). They require no adjustment. Figure 23 18647 Disc Scraper Adjustment 2019-07-18 3P1006NT 313-521M...
  • Page 40 - this task can be performed with discs mounted) ® To lock up Seed-Lok wheels: 1. Pull catch wire aside 2. Pull firming-wheel arm up and release wire to catch arm. Figure 25 27122 ® Seed-Lok Lock-Up 3P1006NT 313-521M 2019-07-18...
  • Page 41 To adjust, first raise drill slightly, then lift and slide T-handles on top of openers. • For shallower seeding, slide T-handles toward drill. Figure 26 15659 • For deeper seeding, slide T-handles away from drill. Press Wheel Adjustment 2019-07-18 3P1006NT 313-521M...
  • Page 42 Check tire size and air pressure (page 58). Build up of seed treatment in feed Clean out seed treatment from feed cups. cup. Incorrect rate adjustment. Check gearbox, sprocket, seed rate handle and seed door settings. Perform calibration if not already done. 3P1006NT 313-521M 2019-07-18...
  • Page 43 Coulters set too deep or spring force Correct adjustment (page 30). too deep too high Incorrect press wheel adjustment. Set press wheels to a shallower depth. Coulters and openers Drill at a slight angle to rows. plugging in no-till conditions 2019-07-18 3P1006NT 313-521M...
  • Page 44 Check that acremeter is for your drill. Activate display. Lower left corner must be “568.7 revs/ac” or “1405.3 revs/ha”. Contact dealer if otherwise. Acremeter battery failing Replace acremeter (page 26). Unit is sealed and battery is not replaceable. 3P1006NT 313-521M 2019-07-18...
  • Page 45 58. 5. Inspect hydraulic hoses for cuts, cracks and aging. Check fittings for evidence of leaks. 6. Replace any worn, damaged or illegible safety decals. Order new decals from your dealer. See “Safety Decals” on page 5. 2019-07-18 3P1006NT 313-521M...
  • Page 46 1. Loosen the jam nut 2. Turn the bolt clockwise until the spring is fully compressed. 3. Back the bolt out in. (6 mm). 4. Tighten the jam nut. Figure 28 32059 Rear Caster Adjustment Bolts (left side shown) 3P1006NT 313-521M 2019-07-18...
  • Page 47 Native Grass Box Open Water wash-out is not recommended for the Native Grass box, particularly if seed lubricants have been used. Water may cause build-up of solidified residue. Filler material used in native grass mixes can also present problems. 2019-07-18 3P1006NT 313-521M...
  • Page 48 Coulter Disc Replacement Replace 17 in. (43.2 cm) coulter blades when adjusting drill level becomes difficult. Two signs that blade replace- ment is indicated are: • Coulter height adjustments drill-wide are using the lowest axle hole (page 30). 3P1006NT 313-521M 2019-07-18...
  • Page 49 “T” top resting on top of bracket. If a seed firmer is also installed, it may be necessary to shorten the flap. Figure 35 31047 Seed Tube Flap 2019-07-18 3P1006NT 313-521M...
  • Page 50 Moving the eye bolt higher decreases height. 5. Tighten the jam nut. 6. Lower the drill and check the setting. The factory setting for eye bolt reveal is: in. (88.9 mm) Figure 36 32060 Lift-Assist Eye Bolt 3P1006NT 313-521M 2019-07-18...
  • Page 51 8. Set circuit to Neutral and shut off tractor. 9. Tighten JIC fitting to 18-20 ft-lbs (24-27 N-m). 10. With cylinder bled and tightened, raise drill and re-install removed lock channel or spacers. 2019-07-18 3P1006NT 313-521M...
  • Page 52 Lift-Assist Arm Pivot One zerk each pivot; 4 total Type of Lubrication: Grease Quantity = Until grease emerges 32068 Caster Pivots One zerk each pivot; 2 total Type of Lubrication: Grease Quantity = Until grease emerges 32061 3P1006NT 313-521M 2019-07-18...
  • Page 53 Felt Barrier Seals 16381 1 seal at each shaft end, 2 total Type of Lubrication: Oil Quantity: Soak seal Note: If Small Seeds is also installed, access these seals from below or through the end wall gaps. 2019-07-18 3P1006NT 313-521M...
  • Page 54 See “Chain Routing” starting on page 60 for locations all chains by drill configuration. Type of Lubrication: Chain Lube Quantity = Coat thoroughly. 12227 Coulter Hub Bearings Seasonal One zerk per coulter; 15 total Type of Lubrication: Grease Quantity = Until resistance is felt 13879 3P1006NT 313-521M 2019-07-18...
  • Page 55 Spread a small skim coat of anaerobic sealant ® (Loctite 525 or equivalent) to gear case mating Use sparingly. Excess sealant may squeeze off the intended surfaces before bolting them back together. surface and lock bearings or gears. 2019-07-18 3P1006NT 313-521M...
  • Page 56 Options Acre/Hectare Meter A digital acremeter is standard on 3P1006NT drills, programmed for the revs/area of the 3P1006NT, and in the units of measure typical for the destination. Order one of the following if you prefer alternate units of measure.
  • Page 57 Small Seeds. The Fertilizer attachment is not compatible with the Native Grass. For operation, see: “Loading Materials” on page 25, “Setting Fertilizer Rate” in Seed Rate Manual, and “Fertilizer Box Clean-Out” on page 44. 28220 2019-07-18 3P1006NT 313-521M...
  • Page 58 Option (or kits). Native Grass is compatible with an existing, concurrent, or subsequent installation of the Small Seeds attachment. For operation, see: “Loading Materials” on page 25, “Setting Native Grass Seed Rate” in Seed Rate Manual, and; “Native Grass Box Clean-Out” on page 43. 28222 3P1006NT 313-521M 2019-07-18...
  • Page 59 Number RMVBL SMALL SEED BOX PARTITION 123-409D 17028 Seed Firmers The standard 3P1006NT drill includes seed flaps. Only one type of optional seed firmer may be installed at the same time. Order one firmer kit per opener. ® Seed-Lok Seed Firmer...
  • Page 60 Dual Seed, Fertilizer or Native Grass. For operation, see: “Loading Materials” on page 25, “Small Seeds Rate” in Seed Rate Manual, and; “Small Seeds Box Clean-Out” on page 44. 28219 3P1006NT 313-521M 2019-07-18...
  • Page 61 “Weight Bracket Installation” on page 85, and “Drill Weight Adjustment” on page 32. 28226 Second Ladder The second ladder can installed on the opposite end of the walkboard from the standard ladder. Description Part Number L ADDER ASSEMBLY 119-020A 68622 2019-07-18 3P1006NT 313-521M...
  • Page 62 Tire warranty information is found online at 50 psi the manufacturer’s websites listed below. For assis- 5.70-8 8-Ply 345 kPa tance or information, contact your nearest Authorized Farm Tire Retailer. ManufacturerWebsite Firestonewww.firestoneag.com Goodyearwww.goodyearag.com BKTwww.bkt-tirestires.com/en Gleasonwww.gleasonwheel.com Titanwww.titan-intl.com 3P1006NT 313-521M 2019-07-18...
  • Page 63 = nominal thread diameter in mm x thread pitch 1180 2640 1950 4290 3160 ⁄ d. ft-lb = foot pounds 1330 2970 2190 4820 3560 ⁄ 25199m 25199 Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above. 2019-07-18 3P1006NT 313-521M...
  • Page 64 This assembly drives the Main Seed Box (via the gearbox), and if installed, the optional Main Box Agitator, Fertilizer attachment, and/or Small Seeds attachment. See “Left Gearbox to Main Seed Box Meters” on page 61 for gearbox output chain routing. 188P 28279 3P1006NT 313-521M 2019-07-18...
  • Page 65 Appendix A - Reference Information Left Gearbox to Main Seed Box Meters See “Standard (Left) Ground Drive to Gearbox” on page 60 for gearbox input. Main box meters are the only meters coupled to the left gearbox output. 28385 2019-07-18 3P1006NT 313-521M...
  • Page 66 Native Grass (Right) Ground Drive (Option) See “Right Gearbox to Native Grass Meters (Option)” on page 63 for Native Grass gearbox output. One sprocket from storage tower is mounted at Native Grass meter shaft (the 17T as shipped). 28368 3P1006NT 313-521M 2019-07-18...
  • Page 67 62 for Native Grass gearbox input. Table 1: Native Grass Driven Sprocket: 14T through 23T from storage tower (ships with 17T, shown on this page) Native Grass Gearbox Output Sprocket: Standard drill: 19T with Rate Reduction kit: 12T 28298 2019-07-18 3P1006NT 313-521M...
  • Page 68 Appendix A - Reference Information Main Seed Box Agitator (Option) No Fertilizer or Small Seeds installed. 112P 28301 Agitator and Fertilizer Drive (Options) No Small Seeds installed. See “Fertilizer Box Drive (Option)” on page 66 for Fertilizer Box drive. 28331 3P1006NT 313-521M 2019-07-18...
  • Page 69 Agitator and Small Seeds Drive w/Native Grass (Options) No Fertilizer installed. See “Agitator and Small Seeds Drive (Options)” on page 65 if Native Grass not installed. See “Small Seeds Box Drive (Option)” on page 68 for Small Seeds Box drive. 28327 2019-07-18 3P1006NT 313-521M...
  • Page 70 No Main Seed Box Agitator installed. See “Fertilizer Box Drive (Option)” on page 66 for Fertilizer Box drive. 28302 Fertilizer Box Drive (Option) See “Small Seeds Box Drive with Fertilizer (Option)” on page 69 if Small Seeds also installed. 28345 3P1006NT 313-521M 2019-07-18...
  • Page 71 Small Seeds Drive w/Native Grass (Options)” on page 65 if Main Box Agitator is also installed, with or without Native Grass installed. See “Small Seeds Box Drive (Option)” on page 68 for Small Seeds Box drive details. 28333 2019-07-18 3P1006NT 313-521M...
  • Page 72 Drive w/Native Grass (Options)” on page 68 for Accessory Jackshaft to Small Seeds chain detail. Table 1: Accessory to Small Seeds chain: 122P If Small Seeds only Option 214P if Native Grass installed (see page 69 if Fertilizer installed) 28345 3P1006NT 313-521M 2019-07-18...
  • Page 73 Appendix A - Reference Information Small Seeds Box Drive with Fertilizer (Option) When Fertilizer is also installed, Small Seeds Jackshaft is driven from Fertilizer jackshaft. If Fertilizer is not also installed, see “Small Seeds Box Drive (Option)” on page 68. 13742 2019-07-18 3P1006NT 313-521M...
  • Page 74 Table of Contents Appendix A - Reference Information Dual Seed Drive (Option) Dual box meters are driven by the right-hand gearbox. 31627 3P1006NT 313-521M 2019-07-18...
  • Page 75 Table of Contents Appendix A - Reference Information Dual Seed and Small Seeds Drive (Options) Dual box meters are driven by the right-hand gearbox. 31628 2019-07-18 3P1006NT 313-521M...
  • Page 76 Table of Contents Appendix A - Reference Information Hydraulic Diagram Null4: Lift-Assist 32056 3P1006NT 313-521M 2019-07-18...
  • Page 77 27-39 37-53 Unload Truck The 3P1006NT drill is delivered by flatbed truck. When coordinating the unload with the Great Plains driver, plan to position the partially assembled drill at a spot with: • at least 10 ft. (3 m) clearance behind the press wheels, •...
  • Page 78 Orient the wheels with the valve stems to the outside (which is toward the inside if the caster frames are reversed, as in the figure). Secure with bolts and lock washers Figure 42 32117 Mount Wheel 3P1006NT 313-521M 2019-07-18...
  • Page 79 500-064D WASHER - SAFETY CHAIN SA 803-031C NUT HEX 1-8 PLT 804-027C WASHER LOCK SPRING 1 PLT At the threaded end of the pivot pin , add a flat washer , lock washer and nut . Tighten nut to Grade 2 torque. 2019-07-18 3P1006NT 313-521M...
  • Page 80 . Push up inside lock tube. Complete with and bolt Install Caster Zerks 25. Select one: Figure 45 32119 800-001C GREASE ZERK STRAIGHT 1/4-28 Caster Assembled Install zerk in shaft at end of pivot arm tube. 26. Repeat all steps for other caster. 3P1006NT 313-521M 2019-07-18...
  • Page 81 29. Select one: 30. Select ten each: 802-055C HHCS 5/8-11X2 GR5 804-022C WASHER LOCK SPRING 5/8 PLT 803-021C NUT HEX 5/8-11 PLT Attach lift assist bolt on mount to frame mount weldment using bolts, washers and nuts. 2019-07-18 3P1006NT 313-521M...

  • Page 82: Table Of Contents

    36. Repeat step 32 through step 34 for the upper arms and upper holes. Install Arm Zerks 37. Select four: Figure 48 32116 800-001C GREASE ZERK STRAIGHT 1/4-28 Parallel Arm Parts Install one zerk in middle of top and bottom cross bar of each parallel arm. 3P1006NT 313-521M 2019-07-18...

  • Page 83: Figure

    JIC (Joint Industry Conference, 37  flare) or NPT (National Pipe Thread, tapered thread) fittings. Avoid bleeding at: ORB (O-Ring Boss) Never bleed pressurized lines at: QD (Quick Disconnect) fittings. See “Bleeding Hydraulics” on page 47. Figure 50 32056 Lift-Assist Cylinder Bleed 2019-07-18 3P1006NT 313-521M...
  • Page 84 52. Install the amber lamp to the light mount with two 1/2-20x3/4 inch self tapping screws 53. Repeat the procedure for the other amber lamp. Figure 52 68366 Brackets for Amber Lights 3P1006NT 313-521M 2019-07-18...

  • Page 85: Select Four

    63. Use a wire tie to connect the wiring harness to the mounting post for the SMV 64. Connect the wiring harness to the two red lights. Figure 54 68384 Wishbone Harness Routing 2019-07-18 3P1006NT 313-521M...
  • Page 86 . Place it onto the outlet end of the hose , up against the ribs. Slide the outlet end of the hose fully onto the small seeds tube inlet at the rear row unit opening . Move the clamp to halfway onto the hose neck. 3P1006NT 313-521M 2019-07-18...
  • Page 87 804-009C WASHER LOCK SPRING 5/16 PLT 803-008C NUT HEX 5/16-18 PLT Orient the reflector upright, and red/orange reflective side to rear. Secure mount to lift-assist pivot with bolts , lock washers and nuts Figure 56 32531 SMV Reflector 2019-07-18 3P1006NT 313-521M...
  • Page 88 ® If a Seed-Lok is present (not shown), secure the ® scraper assembly to the Seed-Lok , using a ® threaded hole present in the Seed-Lok . The hex nut unused. 8. Re-mount the removed disc blade. 3P1006NT 313-521M 2019-07-18...
  • Page 89 11. Repeat step 1 through step 10 for the right side of the drill. See “Drill Weight Adjustment” on page 32 for weight selection. 2019-07-18 3P1006NT 313-521M...
  • Page 90 This warranty is not valid unless the unit is registered with Land Pride within 10 days from the date of the original purchase.
  • Page 92 Table of Contents Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com...