Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
MRKP2
Keypad controller
North American Standard
Safety Information
Read Information — All the safety and operating information should be read before the
appliance is operated.
Follow Information — All operating and use information should be followed.
Retain Information — The safety and operating information should be retained for
future reference.
Heed Warnings — All warnings on the appliance and in the operating instructions
should be heeded.
Wall Mounting — Mounting of this appliance should be done only by an authorized
installer.
Non-Use Periods — Appliances that are left unattended and unused for long periods of
time should be de-energized.
Water — Do not use the apparatus near water.
Cleaning — Unplug the controller unit (MX88/MRC88m/MRAUDIO8x8m) from the
power outlet before cleaning the MRKP2. Use only a dry cloth to clean the apparatus.
Object and Liquid Entry — Never insert objects of any kind through the openings of
these appliances, as they may touch dangerous voltage points or short-circuit parts that
could result in a fire or electric shock. Care should be taken so that objects do not fall
and liquids are not spilled into the appliance through openings in the enclosure.
Servicing — Do not attempt to service these appliances yourself, as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Damage Requiring Service — These appliances should be serviced by qualified
service personnel when:
A power supply connection or a plug has been damaged or
If liquid has been spilled into the appliance or objects have fallen into the appliance
or
The appliance has been exposed to water or moisture or
The appliance does not appear to operate normally or exhibits a marked change in
performance or
The appliance has been dropped or the enclosure damaged.
Replacement Parts — When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or that have the
same characteristics as the original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards. The Master Control Unit battery should be replaced
only after turning the power off and only by an authorized installer.
1
Advertisement
Related Manuals for Xantech MRKP2
Summary of Contents for Xantech MRKP2
- Page 1 Cleaning — Unplug the controller unit (MX88/MRC88m/MRAUDIO8x8m) from the North American Standard power outlet before cleaning the MRKP2. Use only a dry cloth to clean the apparatus. Object and Liquid Entry — Never insert objects of any kind through the openings of these appliances, as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock.
- Page 2 It is important to properly care for your MRKP2 Keypad. Follow these guidelines to ensure your device is preserved and protected. • Do not expose the MRKP2 to rain, liquids or moisture for an extended period of time. • Do not expose the MRKP2 to temperature extremes.
- Page 3 Typically, a zone is comprised of features and capabilities of the MX88. The MRKP2 features hard buttons for a single room, but it is possible for a zone to spread across multiple rooms source selection, volume control, mute, and power.
- Page 4 Typically wires must be fished into position through walls, floors and ceilings. Holes must be cut; speakers The MRKP2 boasts full source control capability and a super bright TFT LCD mounted directly in the ceiling or walls with no electrical back- brackets and touch-screen and its current draw is therefore slightly higher than lesser keypads and local source wall plates must be mounted in existing drywall.
- Page 5 Cable Wire Color Pin # Signal • at Keypad Tone Control functions of the MRKP2 can be entered by pressing the white/orange 485 + orange 485 - Next arrow once inside a source control page. Please note that each of...
- Page 6 Mount the Trim Plate Bracket as shown in the Figure 2.5 on next page, and then snap the Screw-less Trim Plate in place. TO EXPANSION Note: Do not mount the MRKP2 in the same electrical back- box as high KEYPAD voltage devices such as electrical outlets or switches.
- Page 7 POWER and “X” buttons (see Figure 2.3). The internal IR receiver receives IR commands for the MRKP2 and for the MX88. It will also pass-thru IR remote control commands to audio sources, via an emitter, to each of the sources connected to the MX88.
- Page 8 Use an external Xantech IR Receiver in cases where a hand-held remote Initial Power-up needs to be pointed somewhere other than at the MRKP2 or in cases where Whenever the MX88 or the keypad itself is reset, the MRKP2 will take additional interference requires the use of a different type of IR receiver or IR approximately 1 minute to initialize.
- Page 9 “Please Restart The Keypad”. To exit this mode, press the “RESET” button behind the MRKP2 trim panel with a blunt object (see figure on page 15). The keypad will reboot and display “Please Load Application Files”. Press the “RESET”...
-
Page 10: Troubleshooting
5. Troubleshooting 6. Specifications Symptom Possible Cause Solution MRKP2 basic dimensions and cable lengths Verify wiring pin-out and RJ- 45 crimp. Correct by re- 1. RJ-45 plug crimped 4-1/2” (114mm) wide x 4-5/8” (117mm) high x 1/4” crimping RJ-45 to CAT-5 Front panel dimensions incorrectly;... - Page 12 Any products returned to Xantech and found to be defective by Xantech within the warranty period will be repaired or replaced, at Xantech’s option, at no charge. Xantech will not be responsible for the actual cost of the installation or removal of the product, nor for any incidental or consequential damages.
Need help?
Do you have a question about the MRKP2 and is the answer not in the manual?
Questions and answers