Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
MRKP1
Keypad controller
North American Standard
Safety Information
Read Information — All the safety and operating information should be read before the
appliance is operated.
Follow Information — All operating and use information should be followed.
Retain Information — The safety and operating information should be retained for
future reference.
Heed Warnings — All warnings on the appliance and in the operating instructions
should be heeded.
Wall Mounting — Mounting of this appliance should be done only by an authorized
installer.
Non-Use Periods — Appliances that are left unattended and unused for long periods of
time should be de-energized.
Water — Do not use the apparatus near water.
Cleaning — Unplug the apparatus from the power outlet before cleaning. Use only a dry
cloth to clean the apparatus.
Object and Liquid Entry — Never insert objects of any kind through the openings of
these appliances, as they may touch dangerous voltage points or short-circuit parts that
could result in a fire or electric shock. Care should be taken so that objects do not fall
and liquids are not spilled into the appliance through openings in the enclosure.
Servicing — Do not attempt to service these appliances yourself, as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Damage Requiring Service — These appliances should be serviced by qualified
service personnel when:
A power supply connection or a plug has been damaged or
If liquid has been spilled into the appliance or objects have fallen into the appliance
or
The appliance has been exposed to water or moisture or
The appliance does not appear to operate normally or exhibits a marked change in
performance or
The appliance has been dropped or the enclosure damaged.
Replacement Parts — When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or that have the
same characteristics as the original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards. The Master Control Unit battery should be replaced
only after turning the power off and only by an authorized installer.
1
Advertisement
Related Manuals for Xantech MRKP1
Summary of Contents for Xantech MRKP1
- Page 1 Care should be taken so that objects do not fall and liquids are not spilled into the appliance through openings in the enclosure. MRKP1 Servicing — Do not attempt to service these appliances yourself, as opening or Keypad controller removing covers may expose you to dangerous voltage or other hazards.
- Page 2 It is important to properly care for your MRKP1 Keypad and Amplifier. Follow these guidelines to ensure your device is preserved and protected. • Do not expose the MRKP1 to rain, liquids or moisture for an extended period of time. •...
- Page 3 A Zone is defined as an area of the house that has separate source selection The Xantech MRKP1 is a zone controller specifically designed for the MRC88m capabilities from all other areas of the house. Typically, a zone is comprised of or MRAUDIO8x8m systems.
- Page 4 Planning Before installing the MRKP1, it is essential to have a detailed and accurate system design. The first step to a good design is to map the system. It is advisable to mark up a copy of the house floor plan with speaker, keypad and equipment locations, etc.
-
Page 5: Item Description
MRKP1 – REAR CONNECTORS MRKP1 – FRONT PANEL CONTROLLER EXPANSION Figure 2.2: Front of MRKP1 Keypad Figure 2.3: Rear connector board of MRKP1 Keypad ITEM DESCRIPTION ITEM DESCRIPTION Display Controller RJ-45 Port SOURCE Selection Internal IR Sensor Enable/Disable VOLUME Adjustment... - Page 6 Installation Note: Do not mount the MRKP1 in the same electrical back- box as high voltage devices such as electrical outlets or switches. The MRKP1 is designed to mount in a standard single-gang electrical back- box (J Box – see Specifications sections for details). Typical mounting height is 56-60 inches (1.53 meters) from the floor to the bottom of the frame.
- Page 7 The internal IR receiver is located beneath the center of the keypad’s face MRKP1 to MRC88m and Expansion Keypads plate. The internal IR receiver receives IR commands for the MRKP1 and for Each RJ-45 connector under each PREAMP OUT (1 – 8) is considered a “Zone the MRC88m.
- Page 8 Use an external Xantech IR Receiver in cases where a hand-held remote To access the Main Setup Menu, needs to be pointed somewhere other than at the MRKP1 or in cases where 1. Press and hold down the “X” key for at least 3 seconds.
-
Page 9: User Setup Parameters
RESTORE the settings above. INST SETUP PARAMETERS QUICK CONFIG “X” Launches Xantech Quick Config. Function. Press to start process. Refer to the Dragon Quick Config manual for details on setting up Quick Config. KP ADDR (Keypad address) Assigns a different keypad address for each keypad when using multiple keypads in one zone. -
Page 10: Troubleshooting
Solution MRC88m / MRAUDIO8X8m require Firmware Ver. 2.03 or later to work with the MRKP1) 1. RJ-45 plug crimped Verify wiring pin-out and MRKP1 does not power incorrectly; or wiring RJ-45 crimp. Correct by pin-out of RJ-45 re-crimping RJ-45 to reversed. -
Page 11: Specifications
6. Specifications MRKP1 basic dimensions and cable lengths 4.7” height x 2.9” width x 0.35” thick Front panel dimensions 119.4mm height x 75.7mm width x 8.9mm thick 4.0” (101.6mm) x 2.25” (57.5mm) width square Typical wall hole size hole when using Standard North American single- gang back box or bracket. - Page 12 Any products returned to Xantech and found to be defective by Xantech within the warranty period will be repaired or replaced, at Xantech’s option, at no charge. Xantech will not be responsible for the actual coast of the installation or removal of the product, nor for any incidental or consequential damages.
Need help?
Do you have a question about the MRKP1 and is the answer not in the manual?
Questions and answers