Advertisement
Quick Links
Instruction
manual
Ed & Co™ multi-fix™
capsule base series 2
Model PA0101
Keep for future reference.
To reduce the risk of serious injury or death, read this owner's
manual prior to installing and using this product.
The multi-fix base and capsule are suitable for infants up to 13 kg.
Conforms to European ECE R44/04 in Group 0+ as approved by
Land Transport NZ.
designed in NZ
Advertisement
Related Manuals for Edwards & Co Ed & Co multi-fix PA0101
Summary of Contents for Edwards & Co Ed & Co multi-fix PA0101
- Page 1 Instruction manual Ed & Co™ multi-fix™ capsule base series 2 Model PA0101 Keep for future reference. To reduce the risk of serious injury or death, read this owner’s manual prior to installing and using this product. The multi-fix base and capsule are suitable for infants up to 13 kg. Conforms to European ECE R44/04 in Group 0+ as approved by Land Transport NZ.
- Page 2 Introduction Hey there! Firstly, thanks for choosing Edwards & Co - it truly means a lot to us that you have chosen our capsule and base to keep your family safe. We have put a great deal of effort into ensuring that your base is the safest it can be.
- Page 3 GENERAL WARNINGS SERIOUS INJURY or DEATH, read this owner’s To reduce the risk of manual and your vehicle owner’s manual before installing and using this base. By properly using this base and following these instructions, you will greatly reduce the risk of serious injury or death to your child from a collision.
- Page 4 Features of your car seat base Stabiliser Guard Seat Belt Lock-off Car Seat Release Button ISOFIX Fixing Lock Stand Stand Release Button ISOFIX Installation Guides designed in NZ...
- Page 5 Where to install your base IMPORTANT - This multi-fix base is only suitable for approved vehicles fitted with ISOFIX or 3 point seat static or retractable seat belt. IMPORTANT - Only install the seat in a forward-facing passenger seat as indicated in Figure (1) above. A forward-facing seat is one that faces in the direction of the car’s movement.
- Page 6 Important information This multi-fix base may be installed to your car using the ISOFIX system (if fitted) OR the 3-point seat belt system. Refer to the section “Where to install your base” for the locations suitable for installation. ISOFIX The ISOFIX system consists of two anchors at the bottom corner of your vehicle’s passenger seats.
-
Page 7: Assembling The Base
Assembling the base This section shows how to assemble the base when opened from the box. Tools required - small “Phillips” screwdriver Put the tubes on the stabiliser guards into the socket. Press the tube down firmly until they reach the bottom of the socket. - Page 8 Installing the base using ISOFIX Insert the ISOFIX installation guides in between the seat fabric as shown in Figure (1). These guides make installing the base easier by uncovering the location of your vehicle’s ISOFIX anchors. They aren’t always helpful depending on your vehicle.
- Page 9 Installing the base using ISOFIX Press the stand release button and extend the stand feet to lightly touch the floor of your vehicle. WARNING - always check that the base sits level or slightly sloped towards the bottom of your vehicle’s passenger seat. You can use the level indicator found on the car seat capsule for guidance (see the instructions provided for your capsule).
- Page 10 Installing the base using seat belts Open the base stand by pressing the stand release button and moving the locking clip from position 2 to 1 as shown in Figure (2) on page 8. Thread the lap belt and shoulder belt of your vehicle’s 3-point seat belt through the seat belt guide stickers found on the base (as shown...
- Page 11 Installing the base using seat belts Press the stand release button and extend the stand feet to lightly touch the floor of your vehicle. The completed installation should resemble the figure on the left. WARNING - when installing the base with seat belts, it is only suitable for 3-point static or retractable versions.
- Page 12 Installing and removing capsule Installing: Place the car seat capsule onto the base CLICK! until you hear a distinct capsule should be firmly secured. You can check this by firmly pulling the seat upwards. IMPORTANT - The handle must be positioned in B when driving.
-
Page 13: Warranty Information
Warranty information All Edwards & Co products are guaranteed for two years from the date of purchase against defects in material and workmanship. If we determine that the product has a manufacturing fault, we will repair or replace it free of charge to you. The decision to repair or replace is solely at the discretion of Edwards &... - Page 14 edwardsandcobaby.com...