Download
Share
Print this page
Edwards & Co PA0101 Instruction Manual
  1. Manuals
  2. Brands
  3. Edwards & Co Manuals
  4. Car Seat
  5. Ed & Co multi-fix PA0101
  6. Instruction manual

Edwards & Co PA0101 Instruction Manual

Hide thumbs Also See for PA0101:

Advertisement

Quick Links

Download this manual
INSTRUCTION
MANUAL
AVERY
Car Seat Capsule Base
MODEL PA0101
Keep for future reference.
To reduce the risk of serious injury or death, read this owner's
manual prior to installing and using this car seat.
Suitable from 0 to 13 kg.
Certified to European ECE R44/04 in Group 0+ as approved by
Land Transport NZ.

Advertisement

loading

Related Manuals for Edwards & Co PA0101

Summary of Contents for Edwards & Co PA0101

  • Page 1 INSTRUCTION MANUAL AVERY Car Seat Capsule Base MODEL PA0101 Keep for future reference. To reduce the risk of serious injury or death, read this owner’s manual prior to installing and using this car seat. Suitable from 0 to 13 kg.
  • Page 2 INTRODUCTION Hey there! Thanks for choosing Edwards & Co - it truly means a lot to us that you have chosen one of our car seats to keep your family safe. A lot of time and money is spent ensuring that your car seat is the safest it can be.

  • Page 3: General Warnings

    GENERAL WARNINGS SERIOUS INJURY or DEATH, read this owner’s To reduce the risk of manual and your vehicle owner’s manual before installing and using this base. By properly using this base and following these instructions, you will greatly reduce the risk of serious injury or death to your child from a collision.
  • Page 4 FEATURES OF THIS CAR SEAT BASE Stabiliser Guard Seat Belt Lock-off Car Seat Release Button ISOFIX Fixing Lock Stand Stand Release Button ISOFIX Installation Guides...
  • Page 5 ASSEMBLY This section explains how to assemble the car seat base when opened from the box. Tools required - small “Phillips” screwdriver Put the tubes on the stabiliser guards into the socket. Press the tube down firmly until they reach the bottom of the socket.
  • Page 6 WHERE TO INSTALL THE BASE WARNING - This car seat base is only suitable for approved vehicles fitted with ISOFIX or 3 point seat static or retractable seat belt. WARNING - Only install the car seat base in a forward-facing passenger seat as indicated in Diagram (1) above.
  • Page 7 IMPORTANT INFORMATION This car seat base may be installed to your car using the ISOFIX system (if fitted) OR the 3-point seat belt system. Refer to page 6 for the locations suitable for installation. ISOFIX The ISOFIX system consists of two anchors at the bottom corner of your vehicle’s rear passenger seats.
  • Page 8 ISOFIX - VEHICLE INSTALLATION Insert the ISOFIX installation guides in between the seat fabric as shown in Figure (1). These guides make installing the base easier by uncovering the location of your vehicle’s ISOFIX anchors. They aren’t always helpful depending on your vehicle.
  • Page 9 ISOFIX - VEHICLE INSTALLATION Press the stand release button and extend the stand feet to lightly touch the floor of your vehicle. WARNING - Always check that the base sits level or slightly sloped towards the bottom of your vehicle’s passenger seat. You can use the level indicator found on the car seat capsule for guidance (see the instructions provided for your capsule).
  • Page 10 SEAT BELTS - VEHICLE INSTALLATION Open the base’s stand by pressing the stand release button and moving the locking clip from position 2 to 1 as shown in Figure (2) on page 8. Thread the lap belt and shoulder belt of your vehicle’s 3-point seat belt through the seat belt guide stickers found on the base (as shown...
  • Page 11 SEAT BELTS - VEHICLE INSTALLATION Press the stand release button and extend the stand feet to lightly touch the floor of your vehicle. The completed installation should resemble the figure on the left. WARNING - When installing the base with seat belts, it is only suitable for 3-point static or retractable versions.
  • Page 12 CONNECTING THE CAR SEAT Installing: Place the car seat capsule onto the base until you hear a distinct CLICK! Press your weight on all four corners of the car seat capsule to ensure a good connection on all teeth. Check the connection by attempting to lift the capsule upwards.

  • Page 13: Warranty

    WARRANTY All Edwards & Co products are guaranteed for two years from the date of purchase against defects in material and workmanship. If we determine that the product has a manufacturing fault, we will repair or replace it free of charge to you. The decision to repair or replace is solely at the discretion of Edwards &...