Advertisement
Quick Links
INSTALLATION INFORMATION
EMG MODELS: GARY HOLT- GH SET
SPECIFICATIONS:
Logo Color
Magnet Type
Resonant Frequency (KHz)
Output Voltage (String)
Output Voltage (Strum)
Output Noise (60 Hz)
Output Impedance (Kohm)
Current @9V (Microamps)
Battery Life (Hours)
Maximum Supply (Volts DC)
*Note: Logo Colors are not distinguished on the JH Set
**Note: Magnet Type: C (Ceramic) C/S (Ceramic/Steel)
Installation notes:
All EMG Pickups are compatible with each other. EMG accessories, the VLPF, EXG, SPC or RPC Controls can be added to any EMG Pickup System
without requiring an extra battery. DO NOT reconnect the bridge ground wire, EMG Pickups do not require string grounding. Use the 25K Ohm
controls that are included for best results. If your output jack is a long panel style you will need a stereo jack, use a SwitchCraft 152B , soldering
will be required (see the bottom of page 2). Adjust the pickup level to the strings, and at a distance that works for you, experiment. Alternate
wiring diagrams are available at; emgpickups.com.
Included IN THE SYSTEM:
1 VOLUME CONTROL (25K)
2 TONE CONTROLS (25K)
.235
(6)
.390
.310
(8)
(10)
BATTERY
ADJUSTMENT
BUSS
SCREWS & SPRINGS (2 pr)
Warranty
All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If
upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This
warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.
© 2019 Copyright EMG INC. All Rights Reserved.
2.75
(69.8)
1.50
(38.1)
3.09
(78.5)
3/48 MOUNTING HOLES
MODEL:
NECK 89R
Single-Coil
Copper
A
3.80
1.00
3.00
-107
10
160
1500
27
1 TW P/P SWITCH
W/POT (25K)
2 PICKUP IN/ OUT
BATTERY BUSS
STEREO OUTPUT
JACK
(22.8)
.900
EMG 89R
Dual-Coil
2.00
2.00
4.50
-109
10
TW PICKUP CABLE 16" (40.64cm)
1 PICKUP CABLE 15" (27.94cm) and 15" (38cm)
B245
4 CONNECT CABLES 5.5" (14cm)
OUTPUT CABLE 6" (15cm)
BATTERY CABLE 7" (18cm)
- 9V +
L1 L2
L3
BRIDGE 81
Silver
C/S
1.63
3.00
4.50
-100
10
80
3000
27
.725
(18.4)
Advertisement
Related Manuals for EMG NECK 89R
Summary of Contents for EMG NECK 89R
- Page 1 Warranty All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This warranty covers only those pickups and accessories sold by authorized EMG Dealers.
- Page 2 Pickup Buss, Soldering to the new jack will be required, see diagram #6. 4) Install the EMG Volume and Tone Controls and tighten them in. 4) Install the EMG Volume and Tone Controls and tighten them in.
- Page 3 Plug a connect cable from the Neck Volume control to the Pickup Buss (Position 2) along with the RED of the battery clip. Extra pins are for EMG Accessories. 3) Plug a connect cable from the Pickup Buss (position 3) to the Master Tone 7) Put the battery in the insulating foam and place it securely in the control as shown.
- Page 4 7) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud) Plug a connect cable from the Neck (NK) Volume control to the Neck (NK) Tone along with the RED of the battery clip. Extra pins are for EMG Accessories. control as shown.
Need help?
Do you have a question about the NECK 89R and is the answer not in the manual?
Questions and answers