Page 1
BPC-5015 15” High Speed Panel PC with one PCI slot, 180W ATX P/S...
Page 2
Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. reserves the right to change or improve the contents of BOSER Technology Co., Ltd.
Table of Contents Chapter 1 General Description ........1 1.1 Major Features ............... 2 1.2 Specifications ................ 2 1.3 Panel Specifications ............. 3 1.4 Control Keys ................3 1.5 Dimensions ................4 Chapter 2 Unpacking ..........5 2.1 Opening the Delivery Package..........5 2.2 Inspection................
Page 4
Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment...
Page 5
Safety Instructions The safety recommendations outlined in this section are to be read, understood and followed before operating the product. Keep this information in a safe place for future reference. Failure to comply with any of the following safety procedures could result in serious damage. Do not operate product for any purposes other than its intended use This product is intended for indoor use only Do not operate product if power cord is damaged in anyway...
Page 6
Life Expectancy of Constituent Parts This section describes the life expectancy of constituent parts (backlight, power supply, internal cooling fan and touch screen) which make up to BPC-5015. TFT Display Backlight Display brightness decreases over time with use. The expected operating lifetime of the backlight time to reach 50% initial brightness) is 30,000 hours (assuming continuous lit state at 25 degrees C).
The rear of BPC-5015 design with easy assembly when needed. The BPC-5015 has a 15” touch screen that operates under all types of working environment. It comes with a reliable power supply and three 4cm ball bearing cooling fan that enhance system stability.
180W power supply with UL, CE, CSA, TUV approved Variety of operation system can be used in BPC-5015 The BPC-5015 features an all-in-one flat display and keyboard less operation. The BPC-5015 can be use widely such as, Digital signage, Factory...
Storage: 2.5” HDD space x 1 Slim CD-ROM space x 1 Serial Port: 4 ports USB: USB2.0 port x 6 Keyboard: PS/2 6-pin Mini DIN Mouse: PS/2 6-pin Mini DIN BIOS: Award BIOS with 4Mb Flash EEPROM Watchdog Timer: Reset: 1 sec. ~ 255 min. and 1 sec. or 1 min./step Thermal System: 4cm ball bearing cooling fan x 3 Power In: 180W ATX power supply Temperature: 0~+45°C (operating);...
Chapter 2 Unpacking Opening the Delivery Package The BPC-5015 is packed with an anti-static bag. The board contains sensitive electrical components that are easily damaged by static (electricity). Do not remove the anti-static wrapping until proper grounding have been taken. Safety instruction has been described the anti-static precautions and procedures in the previous.
Chapter 3 Hardware Installation This chapter illustrates how to install components into the Panel PC system. External interface please refers to system board’s manual. HDD/CD-ROM/PCI Card Installation 1. Remove the HDD drive bay holding bracket. 2. Install the holding bracket with HDD.
Page 14
3. Remove the CD-ROM drive holding bracket. 4. Install the holding bracket with CD-ROM.
Chapter 4 Touch Screen Driver Installation This chapter illustrates the detailed information for touch screen driver installation procedures. The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the touch screen driver. The following sections describe the installation procedures of driver based on WIN2000 operating systems.
Page 18
The next screen is “Software License Agreement”, select “I accept” and click on Next>. The next screen is Ready to Install the Program, click on Install.
Page 19
Once the Install Shield Wizard finishes updating your system, it will prompt you to restart the computer. Click on Finish to exit the wizard. 4.1.2 Installing Touch Screen Driver in WIN2000 Insert Utility CD Disk to your CD-ROM drive. The main menu will pop up as shown below.
Page 20
The next screen is Software License Agreement, select I accept and click on Next>. The next screen is Ready to Install the Program, click on Install.
Page 21
Once the Install Shield Wizard finishes updating your system, it will prompt you to restart the computer. Click on Finish to exit the wizard.
Driver Functions 4.2.1 PenMount Control Panel Calibrate To adjust the display with touch screen, click on “Calibrate” button and follow the calibrate point to do the calibration, there are five points on screen for calibration. Draw Test or demonstrate PenMount touch screen operation, also the touch location is shown on the display, touch DRAW to start.
Page 23
About It shows information about PenMount controller and driver version. 4.2.2 PenMount Monitor The PenMount monitor icon is shown in the menu bar of Windows system when turn on PenMount monitor from PenMount Utilities. There are several functions on PenMount monitor: Control Panel When select this function, there is a mouse icon shown in the right-button place of screen.
Need help?
Do you have a question about the BPC-5015 and is the answer not in the manual?
Questions and answers