Related Manuals for Boser BPC-9215-F02
Summary of Contents for Boser BPC-9215-F02
- Page 1 BPC-9215-F02 15” High Speed Panel PC with Touch Screen, Atom™ N550, 2 COM, 6 USB2.0, 180W ATX P/S...
- Page 2 Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. reserves the right to change or improve the contents of BOSER Technology Co., Ltd.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 General Description ........1 1.1 Major Features ............... 2 1.2 Specifications ................ 2 1.3 Dimensions ................4 Chapter 2 Unpacking ..........5 Chapter 3 Hardware Installation ......7 3.1 Install SBC ................7 3.2 Install Hard Disk Driver ............8 3.3 Install Back Cover .............. - Page 4 Chapter 5 AMI BIOS Setup ........23 5.1 Starting Setup ..............23 5.2 Using Setup ................. 24 5.3 Main Menu ................25 4.4 Advanced Settings .............. 25 4.5 Advanced Chipset Features ..........26 4.6 Integrated Peripherals ............27 4.7 Power Management Setup ..........28 4.8 PnP/PCI Configurations ............
- Page 5 Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment...
- Page 6 Safety Instructions The safety recommendations outlined in this section are to be read, understood and followed before operating the product. Keep this information in a safe place for future reference. Failure to comply with any of the following safety procedures could result in serious hazard. Do not operate product for any purposes other than its intended use This product is intended for indoor use only Do not operate product if power cord is damaged in anyway...
- Page 7 Life Expectancy of Constituent Parts This section describes the life expectancy of constituent parts (backlight, power supply, internal cooling fan and touch screen) which make up to BPC-9215-F02. TFT Display Backlight Display brightness decreases over time with use. The expected operating lifetime of the backlight time to reach 50% initial brightness) is 30,000 hours (assuming continuous lit state at 25 degrees C).
-
Page 9: Chapter 1 General Description
General Description The BPC-9215-F02 is a 15” industrial grade Panel PC which comes with a TFT color panel display. The rear design of the BPC-9215-F02 enhances the disassembly process when required. It also supports various mounting solutions like wallmount, or desktop for different application. -
Page 10: Major Features
Major Features The BPC-9215-F02 series comes with the following features: Aluminum front panel design 15” TFT color panel display w/touch screen Intel® Atom™ N550 processor VGA, dual Gigabit Ethernet (option for 3), Audio port 1 x 2.5” SATA HDD space 2 x COM port, 6 x USB2.0 port... - Page 11 Panel & Touch Screen LCD Size 15” Max Resolution 1024(H) x 768(V) pixels RGB strip arrangement Brightness (cd/m 300 (center 1 points Typ.) LCD Color 16.7M colors (6-bits with A-FRC) Pixel Pitch (mm) 0.297 x 0.297 Touch Screen 15” resistive Mechanical &...
-
Page 12: Dimensions
Dimensions... -
Page 13: Chapter 2 Unpacking
Ground the board and exercise extreme care to prevent damage to the board from static electricity. The BPC-9215-F02 delivery package contains the following items: BPC-9215-F02 x 1 w/Power Cable x 1 Utility CD Disk x 1, including User’s Manual x 1... - Page 14 This page intentionally left blank.
-
Page 15: Chapter 3 Hardware Installation
Chapter 3 Hardware Installation This chapter tells how to install components into the Panel PC system. External interface please refers to system board’s manual. Install SBC Follow the photo instruction install the SBC onto the chassis. -
Page 16: Install Hard Disk Driver
Install Hard Disk Driver Follow the photo instruction install the HDD onto the HDD mounting bracket. Follow the photo instruction install the HDD_KIT onto the chassis. -
Page 17: Install
Install Back Cover Follow the photo instruction install the back cover onto the chassis. -
Page 18: Wall-Mount Kit
Wall-Mount Kit... -
Page 19: Chapter 4 Sbc Installation
Chapter 4 SBC Installation This chapter provides the information on how to install the hardware using the HS-1754A. This chapter also contains information related to jumper settings of switch, and watchdog timer selection etc. Before Installation After confirming your package contents, you are now ready to install your hardware. -
Page 20: Board Layout
Board Layout... -
Page 21: Jumper List
Jumper List Jumper Default Setting Setting Page JBAT Clear CMOS: Normal Operation Open K/B, USB1 Power On Function Select: Short 1-2 Disabled LVDS Panel Voltage +5V/+3.3V Select: 3.3V Short 2-3 Inverter +5V/+12V Select: 12V Short 1-2 USB2/USB3 Power On Function Select: Short 1-2 Disabled Mini PCIe Power VCC3.3V/Dual 3.3V... -
Page 22: Connector List
Connector List Connector Definition Page ATXPWR 24-pin ATX Power Connector ---- Daughter Card Connector Daughter Card Connector ---- CDIN CD Audio IN Connector COM1 COM1 Connecter (DB9) ---- COM2 COM2 Connector (2x5 header) CPUFAN/SYSFAN1/SYSFAN2 FAN Connector FP_AUDIO1 Front Panel Audio Connector GPIO_CON GPIO Connector IDE Connector... -
Page 23: System Memory
System Memory The HS-1754A provides two 204-pin SO-DIMM sockets. It supports DDR3 1333MHz up to 2GB. VGA Controller LVDS: LVDS Interface Connector Description PIN Description DDC_DATA DDC_CLK Pin 2 Pin 1 LVDS Header CLKAP CLKAN DATAP2 DATAN2 DATAP1 DATAN1 DATAP0 DATAN0 PVDD PVDD... -
Page 24: Serial Ata Connector
INVERTER: Inverter Power Connector Description Backlight Brightness JP2: Panel Voltage Select Options Settings Short 1-2 +3.3V (default) Short 2-3 JP3: Inverter Voltage Select Options Settings 12V (default) Short 1-2 Short 2-3 Serial ATA Connector NOTE: Please connect SATA CD-ROM device to SATA 1 or SATA2 port only while installing WINXP®... -
Page 25: Serial Port Connectors
Serial Port Connectors JP9: COM2 Pin-9 Function Select Options Settings RS-232 (default) Short 1-2 +12V Short 3-4 Short 5-6 JP10: COM2 Use RS-232/422/485 Select Options Settings RS-232 (default) Short 1-2 RS-485 Short 3-4 RS-422 Short 5-6 COM2: COM2 Connector (5x2 Header) PIN Description PIN Description TX-RXCOM: RS-232/422/485 Connector PIN Description PIN Description... -
Page 26: Usb Port
4.10 USB Port JP1: KB, USB1 Power On Enabled/Disabled Select Options Settings Disabled (default) Short 1-2 Enabled Short 2-3 JP5: USB2/USB3 Power On Enabled/Disabled Select Options Settings Disabled (default) Short 1-2 Enabled Short 2-3 USB2: Internal USB2.0 Connector PIN Description Description -DATA +DATA... -
Page 27: System Front Panel Control
4.12 System Front Panel Control CN1: External Reset Button Description Reset Switch SPEAK: Speaker Connector PIN Description Description SPEAK JW_FP: System Front Panel Control PIN Description Description VCC5 PWRLED HDDLED RSTSW PWRBTN HDD LED PWR LED PWR BTN Reset Switch... -
Page 28: Fan Connectors
4.13 Fan Connectors SYSFN1/SYSFAN2: Fan Power Connector Description +12V Fan Speed CPUFAN: Fan Power Connector Description +12V Fan Speed 4.14 Audio Connectors FP_AUDIO1: Front Panel Audio Connector PIN Description Description MIC2-L AUDIO-GND MIC2-R AUDIO LINEOUT2-R MIC2 SENSE-FB LINEOUT2-L LINE2 CDIN: CD Audio In Connector Description CD-L CD-R... -
Page 29: Mini Pcie Connector
4.15 Mini PCIe Connector JP6: Mini PCIe Power Function Select Options Settings VCC3.3V (default) Short 1-2 Dual 3.3V Short 2-3 4.16 8-bit GPIO Function GPIO_CON: GPIO Connector PIN Description PIN Description GPIO_10 GPIO_64 GPIO_11 GPIO_63 GPIO_12 GPIO_16 GPIO_13 GPIO_17... - Page 30 This page is the blank page.
-
Page 31: Chapter 5 Ami Bios Setup
Chapter 5 AMI BIOS Setup The HS-1754A uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. -
Page 32: Using Setup
Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> keys to change entries, and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. Move to previous item ↑... -
Page 33: Main Menu
Main Menu Advanced Settings... -
Page 34: Advanced Chipset Features
Advanced Chipset Features... -
Page 35: Integrated Peripherals
Integrated Peripherals... -
Page 36: Power Management Setup
Power Management Setup... -
Page 37: Pnp/Pci Configurations
PnP/PCI Configurations PC Health Status... - Page 38 This is the blank page.
-
Page 39: Chapter 6 Driver Installation
Chapter 6 Driver Installation This chapter illustrates the detail information of driver installation procedures. The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the drivers. The following sections describe the installation procedures of the driver based on WINXP operating systems. - Page 40 Immediately after clicking the CHIPSET button in Step 1, the program launches the Setup that will assist you in the installation process. Click on the Next> button to proceed. The License Agreement dialog box then appears on the screen. Choose Yes to proceed.
- Page 41 When the Readme File Information dialog box pops up, just clock on the Next> button to proceed. Please select “Yes, I want to restart my computer now” button then click “Finish” to reboot your system to take the effect once the installation is completed.
-
Page 42: Vga Driver Installation
VGA Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click VGA to install video driver. The Welcome to the Setup program dialog box appears on the screen. Choose Next> to proceed. - Page 43 The Intel® License Agreement dialog box appears on the screen. Choose Yes to proceed. When the Readme File Information dialog box pops up, just click on the Next> button to proceed.
- Page 44 When Setup Progress finished, just click on Next button to proceed. Please select “Yes, I want to restart my computer now” button then click “Finish” to reboot your system to take the effect once the installation is completed.
-
Page 45: Lan Driver Installation
LAN Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click LAN to install RTL8111 LAN driver. When the dialog box below appears, make sure you close all other Windows applications the click on the Next> button to proceed. - Page 46 The Setup Status dialog box then appears on the screen. When setup is finished, please reboot your computer to take the effect.
-
Page 47: Audio Driver Installation
Audio Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click Audio to install VIA audio driver. Once the Setup Wizard appears on the screen, make sure to close applications that are running, and then click on the Next>... - Page 48 Next, License Agreement dialog box will appear on the screen. If you are agreeing the license agreement, choose I Agree and click Next> to process. Setup Wizard will display the driver list. Select on VIA HD Audio Codec Driver and then click on Next> to continue.
- Page 49 Make sure the current setting is correct, and then click on Next> to process. Next will post the message that driver installed successful or not. Click Next> to continue.
-
Page 50: Touch Screen Driver Installation
After the audio driver installation finished, select the Finish and restart to take affect. Touch Screen Driver Installation 6.5.1 Installing Touch Screen Driver Insert the utility CD disk to your CD-ROM drive. The main menu will pop up as shown below... - Page 51 The screen displays copying “Setup Wizard” and “PenMount Utilities Installation” screen plus “welcome” message appear, click on Next>. The next screen is “Choose Install Location”, select “Browse” to choose where to install and click on “Install” to begin installation.
- Page 52 Once the Install Shield Wizard finishes updating your system, click on Finish to exit the wizard. We recommend you to reboot your computer to enable the functions. 6.5.2 Touch Screen Calibrate To adjust the display with touch screen, right click on “PM” in the system tray of WINXP and choose “Control Panel”...
- Page 53 Choose PenMount 6000USB device and click on “Configure” that will display next screen to start calibrate. Click on “Standard Calibration” button and follow the five calibrate points to do the calibration.
- Page 54 This page is the blank page.
Need help?
Do you have a question about the BPC-9215-F02 and is the answer not in the manual?
Questions and answers