Related Manuals for Boser BPF-3315-Z
Summary of Contents for Boser BPF-3315-Z
- Page 1 BPF-3315-Z 15” Fanless Panel PC with Touch Screen, Atom™ N270, 2W Stereo Speaker, 6 COM, 6 USB, 12V DC Adapter...
- Page 2 Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. reserves the right to change or improve the contents of BOSER Technology Co., Ltd.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 General Description ........1 1.1 Major Features ............... 2 1.2 Specifications ................ 2 1.3 Dimensions ................4 Chapter 2 Unpacking ..........5 Chapter 3 Chassis Installation ........7 3.1 Installation SBC ..............7 3.2 HDD Installation ..............8 3.3 WLAN Device Installation ............. - Page 4 Chapter 5 Award BIOS Setup ......... 33 5.1 Starting Setup ..............33 5.2 Using Setup ................. 34 5.3 Main Menu ................35 5.4 Standard CMOS Features ........... 36 5.5 Advanced BIOS Features ........... 37 5.6 Advanced Chipset Features ..........38 5.7 Integrated Peripherals ............
- Page 5 Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment...
- Page 6 Safety Instructions The safety recommendations outlined in this section are to be read, understood and followed before operating the product. Keep this information in a safe place for future reference. Failure to comply with any of the following safety procedures could result in serious damage. Do not operate product for any purposes other than its intended use This product is intended for indoor use only Do not operate product if power cord is damaged in anyway...
- Page 7 Life Expectancy of Constituent Parts This section describes the life expectancy of constituent parts (backlight, power supply, internal cooling fan and touch screen) which make up to BPF-3315-Z. TFT Display Backlight Display brightness decreases over time with use. The expected operating lifetime of the backlight time to reach 50% initial brightness) is 30,000 hours (assuming continuous lit state at 25 degrees C).
-
Page 9: Chapter 1 General Description
Chapter 1 General Description The BPF-3315-Z is an industrial Panel PC features anti-vibration design and is a best cost-effective alternation for users. This precise streamline platform can be applied to Kiosk, DSA, transaction terminal, POS, home security system, ATM system and voting machine parking field and more. -
Page 10: Major Features
Major Features The BPF-3315-Z series comes with the following features: Fanless, aluminum front panel design 15” TFT color panel display w/touch screen Intel® Atom™ N270 processor VGA, Gigabit Ethernet, Audio port 2W Stereo Speaker 1 x 2.5” SATA HDD space 1 x CF, 1 x mini PCI socket 6 x COM port, 6 x USB2.0 port... - Page 11 Storage 1 x 2.5” SATA HDD space 1 x Type II CF socket Expansion Interface 1 x Type III mini PCI socket Watchdog Timer Software programmable time-out intervals from 1~255 sec. or 1~255 min. H/W Status Monitor Monitoring temperatures, voltages status Power 12V 84W DC adapter with lockable jack Operating/Storage Temperature...
-
Page 12: Dimensions
Dimensions Dimension measure in cm... -
Page 13: Chapter 2 Unpacking
Ground the board and exercise extreme care to prevent damage to the board from static electricity. The BPF-3315-Z delivery package contains the following items: BPF-3315-Z x 1, w/Power Cable x 1 Utility CD Disk x 1, including User’s Manual... - Page 14 This page intentionally left blank.
-
Page 15: Chapter 3 Chassis Installation
Chapter 3 Chassis Installation This chapter illustrates how to install components into the Panel PC system. Please refer to the external interface of the board manual of the system. Installation SBC Install the SBC with chassis. Screw the SBC with the front panel. -
Page 16: Hdd Installation
HDD Installation Follow the photo instruction to install the HDD mounting bracket onto the HDD. Follow the photo instruction to install the HDD_KIT onto the chassis. -
Page 17: Wlan Device Installation
WLAN Device Installation User can install the Network antenna module as below. Back Cover Installation Follow the photo instruction to install the back cover onto the chassis. -
Page 18: Wall Mount Kit
Wall Mount Kit Follow the arrow to locate the Panel PC in the wall. - Page 19 Hook the Panel PC with four wall mount fixers (A). And screw the wall mount fixers with the wall by M4X10 Round Head Screw (B).
- Page 20 This page intentionally left blank.
-
Page 21: Chapter 4 Sbc Installation
Chapter 4 SBC Installation This chapter provides the information on how to install the hardware using the HS-8601. This chapter also contains information related to jumper settings of switch, and watchdog timer selection etc. Before Installation After confirming your package contents, you are now ready to install your hardware. -
Page 22: Board Layout
Board Layout Jumper List Jumper Default Setting Setting Page CF Use Master/Slave Select: Slave Open COM 1 Voltage Output Select: RI Short 1-2 COM 2 Voltage Output Select: RI Short 1-2 Panel Voltage Select: +3.3V Short 1-2 Touch Screen Wire Select: 5-Wires Open Clear CMOS: Normal Operation Open... -
Page 23: Connector List
Connector List Connector Definition Page External Reset Button AMP R-Output Port Inverter Power Connector CompactFlash Connector Back-Light VR MIC In/Line Out Connector Serial ATA HDD Plug Connector 8-bit GPIO AMP L-Output Port CN13 SO-DDRII Socket CN14 RS-422/485 Connector CN18/CN10 COM 1/COM 2 Connector (DB9) CN19 LVDS Panel Connector CN20/CN17/CN15/CN11... -
Page 24: System Memory
System Memory The HS-8601 provides one 200-pin SO-DIMM socket at locations CN13. It supports DDR2 up to 2GB SDRAM. VGA Controller The HS-8601 provides CN31 is a 15-pin CRT connector, and CN29 offers an internal 10-pin CRT connector. CN19 is the LVDS interface connectors onboard reserved for flat panel installation. - Page 25 CN3: Inverter Power In Connector Description +12V BK_EN The HS-8601 has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP4 offers two voltage settings for the user. JP4: Panel Voltage Select Options Settings +3.3V (default)
-
Page 26: Serial Ata Connector
JP5: Touch Screen Wire Select Options Settings 5-Wires (default) Open 4/8-Wires Short CN5: Back-Light VR Description Serial ATA Connector You can connect the Serial ATA device that provides you high speeds transfer rates (150MB/sec.). If you wish to use RAID function, please note that these two serial ATA connectors just support RAID0 and only compatible with WIN XP. -
Page 27: Serial Port Connectors
CN7: Serial ATA HDD Plug Connector Description Description SATA_TXP0 SATA_TXN0 SATA_RXN0 SATA_RXP0 +12V +12V +12V Serial Port Connectors The HS-8601 offers NS16C550 compatible UARTs with Send/ Receive 16-byte FIFO serial ports. CN18/CN10: COM 1/COM 2 Connector (DB9) PIN Description PIN Description JP2/JP3: COM 1/COM 2 Voltage Output Select Options Settings... - Page 28 CN20/CN17/CN15/CN11: COM 2~COM 6 Connector (5x2 Header) PIN Description PIN Description CN14: RS-422/485 Connector (3x2 Header, COM 4) PIN Description PIN Description NOTE: The terminal resistance of RX & TX is set at 180 Ω CN12: COM 4 use RS-232 or RS-422/485 Select Options Settings RS-232 (default)
-
Page 29: Ethernet Connector
4.10 Ethernet Connector The HS-8601 provides one RJ-45 connector for 10/100/1000 Based LAN. Please refer to the following for its pin information. When installs OS, this driver namely can automatically install. User does not need to renewal. CN34: RJ-45 Connector PIN Description PIN Description MDI0+ MDI0-... -
Page 30: Cmos Data Clear
4.12 CMOS Data Clear The HS-8601 has a Clear CMOS jumper on JP7. JP7: Clear CMOS Options Settings Normal Operation (default) Open Clear CMOS Short IMPORTANT: Before you turn on the power of your system, please set JP7 to open for normal operation. 4.13 Power and Fan Connectors HS-8601 provides one 5-pin power connector at CN35. -
Page 31: Keyboard/Mouse Connectors
4.14 Keyboard/Mouse Connectors The CN22 is a PS/2 6-pin Mini DIN connector for HS-8601. CN22: PS/2 6-pin Mini DIN Keyboard/Mouse Connector Description Keyboard Data Mouse Data Keyboard Clock Mouse Clock... -
Page 32: System Front Panel Control
4.15 System Front Panel Control The HS-8601 has front panel control at location CN23 that indicates the power-on status. CN1: External Reset Button Description Reset Switch CN23: System Front Panel Control PIN Description Description HDD LED+ Speaker- HDD LED- PWR Button+ PWR Button- Speaker+ Reset Switch+... -
Page 33: Watchdog Timer
4.16 Watchdog Timer Once the Enable cycle is active a Refresh cycle is requested before the time-out period. This restarts counting of the WDT period. When the time counting goes over the period preset of WDT, it will assume that the program operation is abnormal. - Page 34 -------------------------------------- Configure time mode -------------------------------------- MOV DX,2EH MOV AL,F5H OUT DX,AL MOV DX,2FH MOV AL,00H ; Setup second mode, 08H for minute mode OUT DX,AL --------------------------------------- Configure reset time interval --------------------------------------- MOV DX,2EH MOV AL,F6H OUT DX,AL MOV DX,2FH MOV AL,05H ; Setup reset time 5, User can setup from 1~255 OUT DX,AL 2.
-
Page 35: Audio Connectors
4.17 Audio Connectors The HS-8601 has an onboard RealTek ALC202A audio connector. The following tables list the pin assignments of the Line In/Audio Out connector. CN6: MIC In/Line Out Connector PIN Description PIN Description AOUTR MIC_L AOUTL MIC_R CN2/CN9: AMP R/L Output Connector Description +SPK_RO/+SPK_LO -SPK_RO/+SPK_LO... -
Page 36: Mini Pci Connector
JP1: CF Use Master/Slave Select Options Setting Master Short Slave (default) Open CN4: CompactFlash Connector Description Description DATA3 DATA4 DATA5 DATA6 DATA7 SDCS1# SDA2 SDA1 SDA0 DATA0 DATA1 DATA2 470Ω pull GND DATA11 DATA12 DATA13 DATA14 DATA15 SDCS3# EWE0 RESET IORDY DACK IDE LED... -
Page 37: 8-Bit Gpio Function
4.20 8-bit GPIO Function The HS-8601 offers one 8-bit general purpose input/output port. CN8: 8-bit GPIO PIN Description PIN Description GPIO0 GPIO4 GPIO1 GPIO5 GPIO2 GPIO6 GPIO3 GPIO7 W83627EHG Digital I/O 1. Assembly sample code ------------------------------------ Extended function mode ------------------------------------ MOV DX,2EH MOV AL,87H OUT DX,AL... - Page 38 MOV DX,2EH MOV AL,F3H OUT DX,AL MOV DX,2FH MOV AL,00H OUT DX,AL --------------------------------------- Configure input / output --------------------------------------- MOV DX,2EH MOV AL,FOH OUT DX,AL MOV DX,2FH MOV AL,FEH; Setup GPIO bit 0 as output, Note1 OUT DX,AL -------------------------------------------------------------------------------------- **Note 1** Example: Output Bit Instruction...
- Page 39 2. DOS Debug Command: --------------------------------------- o 2e 87 o 2e 87 o 2e 07 o 2f 07 o 2e 29 o 2f 01 o 2e 30 o 2f 01 o 2e f3 o 2f 00 o 2e f0 o 2f fe...
- Page 40 This page is the blank page.
-
Page 41: Chapter 5 Award Bios Setup
Chapter 5 AWARD BIOS Setup The BPF-3315-Z uses AWARD BIOS for the system configuration. The AWARD BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. -
Page 42: Using Setup
Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> keys to change entries, and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. Move to previous item ↑... -
Page 43: Main Menu
Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to enter the sub-menu. Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency/Voltage Control... -
Page 44: Standard Cmos Features
Standard CMOS Features The standard CMOS is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, you must set the HDD mode to LBA mode. -
Page 45: Advanced Bios Features
Advanced BIOS Features This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. Phoenix - AwardBIOS CMOS Setup Utility Advanced BIOS Features CPU Feature [Press Enter] Item Help... -
Page 46: Advanced Chipset Features
Phoenix - AwardBIOS CMOS Setup Utility Hard Disk Boot Priority 1. Cho M. ST313032A Item Help 2. Bootable Add-in Cards ↑↓← →: Select Item +/-/PU/PD: Value F10: Save Esc: Quit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Advanced Chipset Features This section allows you to configure the system based on the specific features of the installed chipset. - Page 47 Flat Panel Type Type 1 640 x 480 18-bit 1Ch Type 2 800 x 600 18-bit 1Ch Type 3 1024 x 768 18-bit 1Ch Phoenix - AwardBIOS CMOS Setup Utility PCI Express Root Port Func PCI Express Port 1 [Auto] Item Help PCI Express Port 2 [Auto]...
-
Page 48: Integrated Peripherals
Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers – a primary and a secondary –... - Page 49 Phoenix - AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode [Enabled] Item Help IDE DMA transfer access [Enabled] On-Chip Primary PCI IDE [Enabled] IDE Primary Master PIO [Auto] IDE Primary Slave PIO [Auto] IDE Primary Master UDMA [Auto] IDE Primary Slave UDMA [Auto]...
-
Page 50: Power Management Setup
Phoenix - AwardBIOS CMOS Setup Utility USB Device Setting USB 1.0 Controller [Enabled] Item Help USB 2.0 Controller [Enabled] USB Operation Mode [High Speed] USB Keyboard Function [Enabled] USB Mouse Function [Enabled] USB Storage Function [Enabled] *** USB Mass Storage Device Boot Setting *** ↑↓←... -
Page 51: Pnp/Pci Configurations
PnP/PCI Configurations This section describes the configuration of the PCI bus system. Peripheral Components Interconnect (PCI), is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. -
Page 52: Pc Health Status
5.10 PC Health Status Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Current System Temp. Item Help Current CPU Temperature FAN1 Speed Vcore +12V 1.5V VBAT(V) ↑↓← →: Select Item +/-/PU/PD: Value F10: Save Esc: Quit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults... -
Page 53: Chapter 6 Driver Installation
Chapter 6 Driver Installation This chapter illustrates the detail information of driver installation procedures. The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the drives. The following sections describe the installation procedures of the driver based on WINXP operating systems. - Page 54 Immediately after clicking the Chipset button in Step 1, the program launches the Setup that will assist you in the installation process. Click on the Next > button to proceed. The License Agreement dialog box then appears on the screen. Choose Yes to proceed.
- Page 55 When the Readme File Information dialog box pops up, just click on the Next> button to proceed. Click on the Finish to completed the installation.
-
Page 56: Vga Driver Installation
VGA Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click VGA to install video driver. The Welcome to the Setup program dialog box appears on the screen. Choose Next> to proceed. - Page 57 The Intel® License Agreement dialog box appears on the screen. Choose Yes to proceed. When the Readme File Information dialog box pops up, just click on the Next> button to proceed.
- Page 58 When Setup Progress finished, just click on Next button to proceed. Please select “Yes, I want to restart my computer now” button then click “Finish” to reboot your system to take the effect once the installation is completed.
-
Page 59: Lan Driver Installation
LAN Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click LAN to install RTL8111 LAN driver. When the dialog box below appears, make sure you close all other Windows applications then click on the Next> button to proceed. - Page 60 The Setup Status dialog box then appears on the screen. When setup is finished, please reboot your computer to take the effect.
-
Page 61: Audio Driver Installation
Audio Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click Audio to install audio driver. When the dialog box below appears, Click on Yes to proceed. -
Page 62: Touch Screen Driver Installation
Please select “Yes, I want to restart my computer now” button then click “Finish” to reboot your system to take the effect once the installation is completed. Touch Screen Driver Installation 6.5.1 Installing Touch Screen Driver Insert the utility CD disk to your CD-ROM drive. The main menu will pop up as shown below... - Page 63 The screen displays copying “Setup Wizard” and “PenMount Utilities Installation” screen plus “welcome” message appear, click on Next>. The next screen is “Choose Install Location”, select “Browse” to choose where to install and click on “Install” to begin installation.
- Page 64 Once the Install Shield Wizard finishes updating your system, click on Finish to exit the wizard. We recommend you to reboot your computer to enable the functions. 6.5.2 Touch Screen Calibrate To adjust the display with touch screen, right click on “PM” in the system tray of WINXP and choose “Control Panel”...
- Page 65 Choose PenMount 6000USB device and click on “Configure” that will display next screen to start calibrate. Click on “Standard Calibration” button and follow the five calibrate points to do the calibration.
-
Page 66: Wireless Lan Device Driver Installation
Wireless LAN Device Driver Installation Insert the utility CD disk to your CD-ROM drive. The main menu will pop up as shown below. After click on “Wireless LAN” that driver will be start to install. The screen displays driver install progress as below. Once the Install Shield Wizard finishes updating your system, click on “OK”...
Need help?
Do you have a question about the BPF-3315-Z and is the answer not in the manual?
Questions and answers