Related Manuals for Boser BPC-6171
Summary of Contents for Boser BPC-6171
- Page 1 BPC-6171 15” Industrial Panel PC with Touch Screen, 180W ATX P/S, 1 x Expansion slot...
- Page 2 Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. reserves the right to change or improve the contents of BOSER Technology Co., Ltd.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 General Description ........1 1.1 Major Features ............... 2 1.2 Specifications ................ 2 1.3 Control Keys ................4 1.4 Dimensions ................4 Chapter 2 Unpacking ..........5 2.1 Opening the Delivery Package..........5 2.2 Inspection................5 Chapter 3 Hardware Installation ......7 3.1 Open the Cover.............. - Page 4 Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment...
- Page 5 Safety Instructions The safety recommendations outlined in this section are to be read, understood and followed before operating the product. Keep this information in a safe place for future reference. Failure to comply with any of the following safety procedures could result in serious hazard. Do not operate product for any purposes other than its intended use This product is intended for indoor use only Do not operate product if power cord is damaged in anyway...
- Page 6 Life Expectancy of Constituent Parts This section describes the life expectancy of constituent parts (backlight, power supply, internal cooling fan and touch screen) which make up to BPC-6171. TFT Display Backlight Display brightness decreases over time with use. The expected operating lifetime of the backlight time to reach 50% initial brightness) is 30,000 hours (assuming continuous lit state at 25 degrees C).
-
Page 7: Chapter 1 General Description
A single drive bay is available for one HDD that can be easily installed before assembly. The BPC-6171 has a 15” display and a touch screen that operates under all types of working environment. It also comes with a reliable power supply and two 4cm ball bearing cooling fan that enhance system stability. -
Page 8: Major Features
Onboard graphics, ethernet controller (by M/B) 1 x 2.5” HDD space, 1 x 3.5” HDD/FDD space, 1 x slim CD-ROM space 2 x 4cm ball bearing cooling fan BPC-6171 provides 2 x COM, 2 x USB, PC/104, PCI expansion slot Specifications System SBC Model Provides PICMG1.3 Full-size or PICMG Bus SBC (option) - Page 9 Dimensions (LxHxW) 43.0 x 32.1 x 8.2 cm Cut Out Size (LxH) 39.7 x 30.6 cm Operation/Storage Temperature 0~+45 degrees C/-20~+70 degrees C FCC/CE Front Panel Protection IP65 compliance Power Supply 100~240V AC in 180W ATX power supply Display LCD Size 15”...
-
Page 10: Control Keys
Control Keys OSD Control Keys Define Menu: Menu/Item select Down: Cursor down control Up: Cursor up control Return: Return to menu Dimensions... -
Page 11: Chapter 2 Unpacking
Chapter 2 Unpacking Opening the Delivery Package The BPC-6171 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety instructions in front of this manual describe anti-static precautions and procedures. - Page 12 This page intentionally left blank.
-
Page 13: Chapter 3 Hardware Installation
Chapter 3 Hardware Installation This chapter tells how to install components into the Panel PC system. External interface please refers to system board’s manual. Open the Cover 1. Please loose screw and open the cover. - Page 14 2. Remove the SBC.
-
Page 15: Hdd/Fdd/Cd-Rom Installation
HDD/FDD/CD-ROM Installation 1. Install a CD-ROM drive. Insert the CD-ROM drive into the upper slim type drive bay. Carefully push the CD-ROM drive into the bay until its screw holes align with the holes on the bay as shown. Then secure the CD-ROM with two screws on each side of the bay. - Page 16 3. Install a slim type CD-ROM drive.
- Page 17 4. Install CD-ROM in three-in-one drive bay. 5. Install 2.5” HDD.
- Page 18 This page intentionally left blank.
-
Page 19: Chapter 4 Touch Screen Driver Installation
Chapter 4 Touch Screen Driver Installation This chapter contains the detailed information of touch screen driver installation procedures. The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the touch screen driver. The following sections describe the installation procedures of driver based on WIN2000 operating systems. - Page 20 The next screen is “Software License Agreement”, select “I accept” and click on Next>. The next screen is Ready to Install the Program, click on Install.
- Page 21 Once the Install Shield Wizard finishes updating your system, it will prompt you to restart the computer. Click on Finish to exit the wizard. 4.1.2 Installing Touch Screen Driver in WIN2000 Insert Utility CD Disk to your CD-ROM drive. The main menu will pop up as shown below.
- Page 22 The next screen is Software License Agreement, select I accept and click on Next>. The next screen is Ready to Install the Program, click on Install.
- Page 23 Once the Install Shield Wizard finishes updating your system, it will prompt you to restart the computer. Click on Finish to exit the wizard.
-
Page 24: Driver Functions
Driver Functions 4.2.1 PenMount Control Panel Calibrate To adjust the display with touch screen, click on Calibration and follow the calibrate point to do calibration, there are five points on screen for calibration. Draw Test or demonstrate PenMount touch screen operation, also the touch location is shown on the display, touch DRAW to start. - Page 25 About It shows information about PenMount controller and this driver. 4.2.2 PenMount Monitor The PenMount monitor icon is shown in the menu bar of WIN2000 system when turn on PenMount monitor from PenMount Utilities. There are several functions on PenMount monitor: Right Click Button When select this function, there is a mouse icon shown in the right-button place of screen.
- Page 26 This page intentionally left blank.
Need help?
Do you have a question about the BPC-6171 and is the answer not in the manual?
Questions and answers