Operation; Adjusting The Working Position - Makita UR202C Instruction Manual

Nylon cutting head
NOTICE:
Be sure to use genuine Makita nylon
cutting head.
► Fig.12: 1. Nylon cutting head 2. Spindle 3. Hex
wrench 4. Loosen 5. Tighten
1. Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2. Place the nylon cutting head onto the spindle and
tighten it securely by hand.
3. Remove the hex wrench from the gear case.
To remove the nylon cutting head, follow the installation
procedures in reverse.
Plastic blade
NOTICE:
Be sure to use genuine Makita plastic
blade.
► Fig.13: 1. Plastic blade 2. Spindle 3. Hex wrench
4. Loosen 5. Tighten
1. Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2. Place the plastic blade onto the spindle and
tighten it securely by hand.
3.
Remove the hex wrench from the gear case.
To remove the plastic blade, follow the installation pro-
cedures in reverse.

OPERATION

Adjusting the working position

CAUTION:
Before performing this procedure,
install the battery cartridge(s) to the portable
power pack and finish the adjustments for the
waist belt and shoulder harness. Refer to the
instruction manual of the portable power pack for
detail.
CAUTION:
To prevent unintentional start up,
never turn on the portable power pack throughout
this procedure. The battery cartridge(s) is to be
installed only to obtain the usability with actual weight
balance.
1. Pull out the cord from the right side of the portable
power pack. When pulling out the cord, be sure to set
the cord in the holders as shown in the figure.
► Fig.14: 1. Cord 2. Holder
2. Wear the shoulder harness of the portable power
pack and lock the buckle on the waist belt.
► Fig.15
3. Insert the plug of the tool into the socket of the
portable power pack.
When inserting, align the triangle marking on both the
plug and the socket.
► Fig.16: 1. Plug 2. Socket 3. Triangle marking
4. Adjust the cord length using the holder as
necessary.
► Fig.17: 1. Holder
The cord length is properly adjusted when you can;
— swing the tool without any hinderance by the cord;
— swing the tool without letting the cord flopping and;
— disconnect the plug from the socket without taking
off the shoulder harness of the portable power pack.
CAUTION:
Allow the cord to have a appro-
priate play between the tool and portable power
pack. If the play is too little, the tool movement may
be hindered. If the play is too much, the cord may be
caught by other object and result in accident.
Starting the operation
CAUTION:
Before operation, finish adjusting
the working position by following the instructions
in the section for the working position.
CAUTION:
Before operation, make sure that
the buckles on the waist belt is locked.
CAUTION:
Always press the main power but-
ton to turn on the tool immediately before cutting
grass. Failure to do so may cause personal injury
due to unintentional start up.
1. Install the battery cartridge(s) to the portable
power pack.
► Fig.18: 1. Portable power pack 2. Battery cartridge
NOTE: Refer to the instruction manual of your
portable power pack for how to install the battery
cartridges.
2. Press the power button on the portable power
pack. The main power lamp will light up.
► Fig.19: 1. Main power lamp 2. Power button
3. Wear the shoulder harness of the portable power
pack and lock the buckle on the waist belt.
► Fig.20
4.
Insert the plug of the tool into the socket of the
portable power pack.
When inserting, align the triangle marking on both the
plug and the socket.
► Fig.21: 1. Plug 2. Socket 3. Triangle marking
5. Tap the main power button to turn on the tool.
The tool is ready to operate. The tool will run when you
pull the switch trigger.
► Fig.22: 1. Main power button
CAUTION:
When suspending the operation,
always turn off the tool and remove the plug from
the socket. Failure to do so may cause personal
injury due to unintentional start up.
When quitting the operation, press and hold the main
power button until the speed indicator goes off and then
perform the above procedure in reverse.
19 ENGLISH