Advertisement
[A.POWAER SETTING]
1 PWM Frequency
2 Punch
3 Compress
4 Throtte Feel
5 Max Reerse Force
[B.Brake Setting]
1 Drag Brake
2 Brake Punch
3 Initia Brake
4 Brake Frequency
5 Max Breke Force
[C.Timing Setting]
1 Boost Timing Activation
2 Boost Timing
3 Boost Start RPM
4 Boost End RPM
5 Turbo Timing
6 Turbo Start
7 Turbo Delay
8 Turbo Up Rake
9 Turbo Down Rake
[D.General Setting]
1 Running Mode
2 Battery
3 Cut off Voltage
4 Esc Over Heat Protect
5 Motor Over Heat Protect
6 Neutral Range
7 BEC Voltage
8 Motor Action
9 Motor Link
10 Remote Off
[E.Limit Vaiue]
1 Voltage Minimum
2 ESC temp Maximum
3 Motor Tempreature maximum
4 RPM Maximum
5 ClearLimit Record
[F.Load Setting ]
1 Blinky Mode
2 Stock Mode
3 Modify mode
4 Custom-1,2,3
[G.Save Setting]
1 Custom-1,2,3
[H.FirmwareUpdete]
1 Load TF File
2 CurrentVersion
Drive frequency can be adjusted. At 2K, feeling of power at low speeds increases, and at 32K, feeling
of power at high speeds increases.
If you set it to 30, you can get the maximum punch when moving forward.
You can adjust the throttle curve. 0% is a linear slot.
Adjust throttle response. 5 is an aggressive throttle.
You can adjust the maximum speed when moving backward.
Automatic brake adjustment when the transmitter throttle is in neutral. 30% is the maximum brake value.
You can adjust the punch when braking. The maximum brake punch is 30%.
You can adjust the effectiveness of the initial brake when operating the brake.
Smooth braking can be obtained by adjusting the brake frequency and increasing the frequency.
Throttle operation, maximum brake effectiveness adjustment.
When you set the boost, you can select the automatic setting or the manual setting of the rotation speed.
When increasing boost timing, this will increase the motor speed and reduce the torque. If boost
value has set too high, motor will become hot and may damage, so it is necessary to pay attention
to the motor temperature and make adjustments.
Adjustment of boost start rotation speed.
Adjustment of boost end rotation speed.
The motor speed can be further increased when the transmitter is fully throttled. If turbo timing is
raised too high, motor will become hot and may be damaged, so it is necessary to pay attention to
the motor temperature and make adjustments.
Timing of entering turbo will be adjusted, and if set to 50%, the timing of entering turbo will be earlier.
The time is adjusted while switching from boost to turbo, and if set to 0.00 seconds, it will switch
from boost to turbo without a time lag, but heat generated by the motor will also increase.
Will be able to adjust the amount of turbo timing increase in 0.5 second increments. Increasing value
may cause the motor to generate heat and cause damage. It is necessary to pay attention to motor
temperature and make adjustments.
Will be able to adjust the amount of turbo timing that drops when throttle is returned in 0.5 second
increments. Increasing value will cause the turbo timing to drop faster and the response will increase,
but if turbo value is large, it may cause a phenomenon like braking.
Three types of operation settings can be set: forward / brake, forward / reverse, forward / reverse / brake.
Select the battery type.
Set the battery cut voltage.
Will be able to adjust the ESC operating cut temperature for ESC protection.
To protect the motor, you can set the temperature to cut operation of ESC when motor temperature
rises too high. This will not work if motor does not have a temperature sensor. ..
Neutral width adjustment.
Will be able to adjust the voltage input to the receiver. When adjusted to 7V, a servo that supports
high voltage is required.
Will be able to set the direction of rotation of the motor.
Will be able to change the motor wire connection order to A.B.C or C.B.A. If needed to change this,
check the ESC settings and connect the motor wire to his A.B.C terminal on the motor. There is a
risk of damage if connected incorrectly.
You can turn off the R160 esc when push and hold the brake to 100% over 8sec.
Minimum voltage during driving is displayed.
Maximum ESC temperature while driving is displayed.
Maximum temperature of motor while driving is displayed.
Maximum number of revolutions of motor while driving is displayed.
Able to erase the data stored by ESC.
Blinky mode and default setup.
Stock mode and default setup.
Modify mode and default set. (Not included in R100)
Able to recall settings stored in Custom 1, 2, and 3. You can call it by pressing enter and then
pressing enter again.
Able to save 3 types of custom-configured data. Press enter and press enter again to save.
Able to update firmware stored on the SD card from your PC to ESC.
Able to check the current ESC version by pressing enter.
Advertisement
