Table of Contents
Related Manuals for Trynex International TurfEx TS45
Summary of Contents for Trynex International TurfEx TS45
- Page 1 Owner’s Manual/Parts List/Assembly Instructions This Manual Must Be Read Before Operating The Equipment TS45 CUSTOMER COPY Madison Heights, Michigan 48071 866-5-TURFEX www.turfexproducts.com © TrynEx International 2014 F51509 REV-A140506...
-
Page 2: Table Of Contents
Component Vocabulary ....................................5 Preparation /Spreading ....................................6 Calibration Instructions ....................................7 Calibration Chart ......................................8-9 Maintenance ......................................... 10 PARTS LIST Parts Breakdown .....................................12-13 ASSEMBLY INSTRUCTIONS Introduction ........................................15 Assembly Instructions ....................................16-22 WARRANTY ........................................23 NOTES ........................................24-27 © TrynEx International 2014 F51509 REV-A140506... -
Page 3: Introduction
Introduction This Owner’s Manual is intended to acquaint you with your TurfEx TS45 Push Spreader and how to operate it safely and correctly. Read this manual and observe the instructions contained to ensure safety and performance. This manual must be read by each person that will be involved in its assembly, operation, care, maintenance, repair, or transport. In addition to this manual, observe all workplace safety practices and take precautionary measures to ensure your own safety and the safety of those around you. -
Page 4: Safety
Empty the spreader and clean it after each use to prevent material from building up and covering metal parts, causing corrosion. Do not use salt. Using salt in this spreader will damage the mechanism and shorten the life of the machine © TrynEx International 2014 F51509 REV-A140506... -
Page 5: Operating Instructions
Evenly distributes material. Clean after each use. Gearbox Do not open the gear box; the gears are lubricated at the factory. Wheels Do not over-inflate! Max 25 PSI (1.72 bar) Support Leg Stabilizes Load and Spreader © TrynEx International 2014 F51509 REV-A140506... -
Page 6: Preparation/Spreading
If spreading material is accidentally deposited too heavily in a small area, soak the area thoroughly with a garden hose or sprinkler to prevent burning of the lawn. To ensure consistent coverage, make sure each broadcast pattern slightly overlaps the previous broadcast pattern. (See Diagram below.) Overlapping For Consistent Coverage. © TrynEx International 2014 F51509 REV-A140506... -
Page 7: Calibration Instructions
Find the gate setting that matches the required output using the values you recorded in the chart. You may need to adjust your walking speed slightly. Gate Stop @ 20 Gate Lever closed © TrynEx International 2014 F51509 REV-A140506... -
Page 8: Calibration Chart
Speed (mph) Spread Width (ft) Material Gate Setting Output (lbs/min) Speed (mph) Spread Width (ft) Material Gate Setting Output (lbs/min) Speed (mph) Spread Width (ft) Material Gate Setting Output (lbs/min) Speed (mph) Spread Width (ft) © TrynEx International 2014 F51509 REV-A140506... - Page 9 Speed (mph) Spread Width (ft) Material Gate Setting Output (lbs/min) Speed (mph) Spread Width (ft) Material Gate Setting Output (lbs/min) Speed (mph) Spread Width (ft) Material Gate Setting Output (lbs/min) Speed (mph) Spread Width (ft) © TrynEx International 2014 F51509 REV-A140506...
-
Page 10: Maintenance
Never exceed load capacity rating of 100 lbs, it will damage the spreader. STORAGE Never allow material to remain in the hopper for extended periods of time. Before storing make sure the spreader is clean, dry, and freshly lubricated. Store indoors. © TrynEx International 2014 F51509 REV-A140506... -
Page 11: Parts List
Parts List TS45 CUSTOMER COPY Madison Heights, Michigan 48071 866-5-TURFEX www.turfexproducts.com © TrynEx International 2014 F51509 REV-A140506... - Page 12 Part Breakdown 8-19 29 31 © TrynEx International 2014 F51509 REV-A140506...
-
Page 13: Parts Breakdown
HANDLE SPACER, TS45 WASHER, M16 R10232 AXLE BUSHING KIT, TS25, TS45 COTTER PIN, M5 X 35 INNER AXLE BUSHING R10222 FRAME HARDWARE KIT, TS45 OUTER AXLE BUSHING BOLT, M6 X 35 BOLT, M6 X 45, HEX © TrynEx International 2014 F51509 REV-A140506... -
Page 14: Assembly Instructions
Assembly Instructions TS45 CUSTOMER COPY Madison Heights, Michigan 48071 866-5-TURFEX www.turfexproducts.com © TrynEx International 2014 F51509 REV-A140506... -
Page 15: Introduction
Introduction These installation instructions have been designed to guide you in assembling your TurfEx TS45 Push Spreader. Read and follow the direc- tions contained to ensure safety and performance through correct assembly. In addition to these instructions, observe all workplace safety practices and take precautionary measures to ensure your own safety and the safety of those around you. - Page 16 B: Fix the wheel frame to the hopper frame using hex bolt M6x60 and lock nut M6. Do not tighten the hardware. Make sure the word “Front” on the Gearbox faces forward (toward the curve on the hopper frame). © TrynEx International 2014 F51509 REV-A140506...
- Page 17 C: Attach wheel to the left side of the axle. Secure with a washer and push nut. D: Install a Push Nut at the other end of the axle. © TrynEx International 2014 F51509 REV-A140506...
- Page 18 Attach the handle shaft to Lower Frame Assembly and fix the pivot & bracket assembly on the Lower Frame Assembly by using two sets of hex bolt M6x55 and lock nut M6. The Bracket should be to the operator’s left. © TrynEx International 2014 F51509 REV-A140506...
- Page 19 A: Push the Gate Lever forward to the lowest position and insert the upper end of Gate Rod into the slot of the Gate Lever. B: Remove one nut from the Gate Rod and insert the rod to Pivot & Bracket Assembly and tighten on the removed nut again. © TrynEx International 2014 F51509 REV-A140506...
- Page 20 Slip the threaded end of Gate Connecting Rod into the Gate with a Cotter Pin Ø2x10 and flat washer Ø6 above the gate; then fasten with flat washer Ø6 and lock nut M6 at the bottom of shut off plate. © TrynEx International 2014 F51509 REV-A140506...
- Page 21 When the Gate Lever is moved fully forward, the holes should close. The holes should be open when the lever is completely back. The Spinner must rotate clockwise to spread correctly. © TrynEx International 2014 F51509 REV-A140506...
- Page 22 Assembly Instructions STEP 11: FINISHING TOUCHES – AGITATOR, SCREEN, RAIN COVER Install the Agitator R-pin on the Spinner Shaft, the Hopper Screen, and the Rain Cover. © TrynEx International 2014 F51509 REV-A140506...
-
Page 23: Warranty
ONE YEAR PARTS LIMITED WARRANTY TrynEx International warrants under the brand name TurfEx. The TurfEx models TS25, TS45 are warranted for a period of one (1) year from the date of purchase, including TrynEx Genuine Parts, against defects in materials or workmanship under normal use and service subject to the limitations detailed below. -
Page 24: Notes
Notes © TrynEx International 2014 F51509 REV-A140506... - Page 25 Notes © TrynEx International 2014 F51509 REV-A140506...
- Page 26 Notes © TrynEx International 2014 F51509 REV-A140506...
- Page 27 Notes © TrynEx International 2014 F51509 REV-A140506...
- Page 28 140506...
Need help?
Do you have a question about the TurfEx TS45 and is the answer not in the manual?
Questions and answers