Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trynex International SnowEx Precision Pro SP-1675
Summary of Contents for Trynex International SnowEx Precision Pro SP-1675
- Page 1 Owner’s Manual This Manual Must Be Read Before Operating The Equipment SP-1675 Serial No. X4-100000 and higher SP-1975 Serial No. X5-100000 and higher CUSTOMER COPY Madison Heights, Michigan 48071 800-SALTERS www.snowexproducts.com © TrynEx International 2013 (REV A) F51073A...
-
Page 2: Table Of Contents
Notes .......................................... 11 Have a question or need assistance? SnowEx Customer Care (800) SALTERS or (248) 586-3500 Monday trough Friday 8:00 AM to 4:30 PM EST Fax: (248) 691-8378 E-mail: customercare@trynexfactory.com Website: www.snowexproducts.com © TrynEx International 2013 (REV A) F51073A... -
Page 3: Introduction
Madison Heights, MI 48071 U.S.A. Control Serial # _____________________________________ 1-800-725-8377 trynexfactory.com Date Purchased _____________________________________ Model No. SP-1675 Dealer where purchased ___________________________________________________ See separate Warranty Information Sheet for your warranty coverage. Serial No. X4-100000 Manuf. 2013 © TrynEx International 2013 (REV A) F51073A... -
Page 4: Safety
Never leave material in hopper between storms, or when storing. Ice melters are hygroscopic and will attract moisture and harden up. Empty the spreader and clean it after each use to prevent ice melter from building up and covering metal parts, causing corrosion. © TrynEx International 2013 (REV A) F51073A... -
Page 5: Operating Instructions
Turn the spreader off with the POWER switch when you are done spreading, or need to pause. The spread pattern will not Vibrator Auger Speed Spinner Speed change as long as the knobs are left in the same position. © TrynEx International 2013 (REV A) F51073A... -
Page 6: Spreading Tips
2 or 4 rower spread pattern. 4 Increase Spinner Speed and drive slower. 5 Increase Spread Width and spread second pass on the way out of the parking lot. © TrynEx International 2013 (REV A) F51073A... -
Page 7: Attaching To Vehicle
Speeds. The Baffles may need adjusted when changing to a different spreading material. Use an 1/2” wrench for the bolts holding the baffles in place. Loosen the bolt to move the baffle. SP-1675 © TrynEx International 2013 (REV A) F51073A... -
Page 8: Adjustable Spinner
When looking down at the spinner, moving the fins counter- adjust the spread pattern toward the left side of the spreader. clockwise will adjust the spread pattern toward the right side of the spreader. © TrynEx International 2013 (REV A) F51073A... -
Page 9: Maintenance Instructions
Instead of oil on the frame, you can use a rust inhibitor spray (read the label before using to make sure it is not damaging to paint). Put Dielectric Grease on all plugs and connections prior to storage. © TrynEx International 2013 (REV A) F51073A... -
Page 10: Troubleshooting
Controller not connected Check all connections at the back of Controller No Display, On/Off Switch does not light up No Power to Controller Reset Breaker Check for Cuts in Battery Harness Test Controller (Contact Dealer) © TrynEx International 2013 (REV A) F51073A... -
Page 11: Notes
Notes © TrynEx International 2013 (REV A) F51073A... - Page 12 133009...
Need help?
Do you have a question about the SnowEx Precision Pro SP-1675 and is the answer not in the manual?
Questions and answers