Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LINOVISION IOT-G65
Summary of Contents for LINOVISION IOT-G65
- Page 1 IOT-G65 LoRaWAN Gateway Quick Start Guide Hangzhou Linovision Co., Ltd.
- Page 2 Welcome Thank you for choosing IOT-G65 LoRaWAN Gateway. This guide teaches you how to install the IOT-G65 and how to log in the web GUI to configure the device. Declaration of Conformity IOT-G65 is in conformity with the essential requirements and other relevant provisions of the CE, FCC, and RoHS.
-
Page 3: Table Of Contents
3.2 Ethernet Cable & Power Cable Installation........6 3.3 Antenna Installation................ 7 3.4 Gateway Mounting................7 4. Access the Web GUI of IOT-G65............9 4.1 Web Access via Ethernet Port............9 5. Connect IOT-G65 to the Network............. 11 5.1 Configure the WAN Connection...........11 5.2 Configure the Wi-Fi Connection...........12... -
Page 4: Packing Listg List
1. Packing Listg Lis Before you begin to install the IOT-G65 LoRaWAN Gateway, please check the package contents to verify that you have received the items below. 1 × IOT-G65 1 × Ethernet Cable 1 × DC Jack Power Adapter 1 ×... -
Page 5: Dimensions (Mm)
B. Rear Panel Bracket Mounting Screws SIM Slot Type-C Port Ethernet Port (PoE) Power Connector Reset Button Waterproof Silicone Cable Groove 2.2 Dimensions (mm) 2.3 LED Indicators Indication Status Description The power is switched off POWER Power Status The power is switched on Blue Light Static: the system is running properly STATUS... -
Page 6: Reset Button
65 does not support hot plugging, please turncut off the power before you insert or take off cards. A. Use screwdriver to Open the protective cover on the back panel of IOT-G65 via screwdriver. B. Push Insert the SIM card into the device according to the direction the icon on the device. -
Page 7: Antenna Installation
IOT-G65 also supports 802.3af standard PoE and can be powered by PoE switch or PoE adapter. When connecting, Ethernet cable of IOT-G65 device side should be installed first, otherwise,or PoE devices or gateway may be damaged. 3.3 Antenna Installation For external antenna version, rotate the antenna into the antenna connector accordingly. - Page 8 6. Screw the bracket fixing screws to the back panel of device, then hang the device to the mounting bracket on the wall. 7. Screw the grounding screw to fix IOT-G65 to the mounting bracket. 3.4.2 Pole Mounting Preparation: mounting bracket, bracket fixing screws, hose clamp and other required tools.
-
Page 9: Access The Web Gui Of Iot-G65
Password: password 4.1 Web Access via Ethernet Port Connect PC to IOT-G65 ETH port directly or through PoE adapter. The following steps are based on Windows 10 operating system for your reference. A. Go to “Control Panel” → “Network and Internet” → “Network and Sharing Center”, then... - Page 10 B. Go to “Properties” → “Internet Protocol Version 4(TCP/IPv4) ”and select “Use the following IP address”, then assign a static IP manually within the same subnet of the gateway. C. Open a Web browser on your PC (Chrome is recommended) and type in the IP address 192.168.1.1 to access the web GUI.
-
Page 11: Connect Iot-G65 To The Network
F. After you log in the Web GUI, you can view system information and perform configuration of the gateway. 5. Connect IOT-G65 to the Network This section explains how to connect the gateway to network via WAN connection, Wi-Fi or cellular. -
Page 12: Configure The Wi-Fi Connection
C. Connect Ethernet port of gateway to network devices like router or modem. D. Log in the web GUI via the newly assigned IP address and go to “Status”→ “Network” to check Ethernet port status. 5.2 Configure the Wi-Fi Connection A. - Page 13 C. Type the correct key of Wi-Fi. E. Go to “Status”→”WLAN” to check Wi-Fi status. If it shows “Connected”, it means gateway connects to Wi-Fi successfully.
-
Page 14: Configure The Cellular Connection
5.3 Configure the Cellular Connection A. Go to “Network” → “Interface” → “Cellular” → “Cellular Setting” page to enable cellular settings. B. Choose relevant network type and fill in SIM card information like APN or PIN code. C. Click “Save” and “Apply” for configuration changes to take effect. -
Page 15: Packet Forwarder Configuration
6. Packet Forwarder Configuration IOT-G65 has embedded multiple packet forwarders like TTN and Chirpstack.This section explains how to connect the gateway to third-party network servers Make sure the gateway connects to the network as shown in Chapter Section 5. - Page 16 B. Fill in the server information and enable this server. Note：When you select anyone of TTN or Chirpstack, other servers are not allow to enable. C. Go to “Packet Forwarder” → “Radio” page to configure antenna transmission type, center frequency and channels. The channels of the gateway and network server need to be the same.
-
Page 17: Network Server Configuration
E. Go to “Traffic” page to view the data communication of IOT-G65. 7. Network Server Configuration IOT-G65 can work as network server and transmit data to Cloud or other platform via MQTT/HTTP/HTTPS. Make sure the gateway connects to the network as shown in Chapter Section 5. - Page 18 B. Go to “Packet Forwarder” → “Radio” page to select the antenna transmission type, center frequency and channels. The channels of the gateway and LoRaWAN nodes need to be the same. Note: For built-in antenna models, please select “2 × Built-in ANT”; for external antenna models, please select “Ext ANT(TX+RX)+ Built-in ANT(RX)”.
-
Page 19: Connect Iot-G65 To Other Platform
D. Go to “Gateway” page and click “Add” to add a gateway. E. The gateway is online. 7.2 Connect IOT-G65 to Other Platform A. Go to “Packet Forwarder” → “General” page to click “enable”. - Page 20 B. Go to “Packet Forwarder” → “Radio” page to select the antenna transmission type, center frequency and channels. The channels of the gateway and LoRaWAN nodes need to be the same. Note: for built-in antenna models, please select “2 × Built-in ANT”; for external antenna models, please select “Ext ANT(TX+RX)+ Built-in ANT(RX)”.
- Page 21 After saving the application, you can select HTTP, HTTPS or MQTT protocol and fill in correspond server information to send data to another server. E. Go to “Profiles” page to add a new profile for the device. F. Go to “Device” page and click “Add” to add LoRaWAN node devices.
- Page 22 You can also click “Bulk Import” if you want to add many LoRaWAN nodes all at once. Click “Template Download” to download template file and add LoRaWAN device information to this file. Application and device profile should be the same as you created on web page. Import this file to add bulks of devices.
- Page 23 F. Go to “Packets” page to check the packets from LoRaWAN node devices. The type starts from “Up” means uplinks and “Dn” means downlinks. Click “Details” to check the properties and payload contents of packets.