Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LENCO CS171 USB
Summary of Contents for LENCO CS171 USB
- Page 1 CS171 USB OWNER'S MANUAL Mobile Audio System PLL Synthesizer Stereo Radio RDS (Radio Data System) operation Digital Compact Disc Player Automatically Memory Storing Slide Down Detachable Panel Preset Equalization Electronic Shockproof (ESP) Function Auxiliary Input Function Remote Control...
-
Page 2: Table Of Contents
CONTENTS Pausing playing Installation Previewing all track Take out screw before installation Repeating the same tracks DIN Front-Mount (Method A) playing all track in random Installing the unit Ejecting a disc Removing the unit MP3 operation DIN Rear-Mount (Method B) Switch to CD (MP3) mode Using The Front Panel Ejecting a disc... -
Page 3: Installation
INSTALLATION Notes: TAKE OUT SCREW BEFORE Choose the mounting location where INSTALLATION the unit will not interfere with the Before install the unit, please remove normal driving function of the driver. the two screws . Before finally installing the unit, connect the wiring temporarily and Take out screw make sure it is all connected up... -
Page 4: Removing The Unit
INSTALLATION middle left and right sides of the unit. Then use the supplied hardware Then slide the sleeve off the back of (Tapping Screw (5x25mm) and Plain the unit. Washer) to attach the other end of metal strap to a solid metal part of the Sleeve L Key vehicle under the dashboard. -
Page 5: Din Rear-Mount (Method B)
INSTALLATION 2. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm)on each side. Note: the outer trim ring, sleeve and the metal strap are not used for method B installation. DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. -
Page 6: Using The Front Panel
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel 1. Press the OPEN button, then the front panel will slide down. The left side The right side Front Panel O P EN 2. When the two sides fixed int palce, 2. -
Page 7: Wiring Connection
WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR IGNITION FUSE SWITCH (ACC+) FUSE MEMORY PINK BACK-UP (B+) BLACK GROUND (B-) (GREY) REAR RCA CABLE Rch RED POWER YELLOW ANTENNA Lch WHITE GREEN GREY FRONT Lch FRONT Rch SPEAKER SPEAKER GREEN/BLACK GREY/BLACK BLUE WHITE REAR Lch REAR Rch... -
Page 8: Operation
OPERATION LOCATION OF KEYS... -
Page 9: Switching On/Off The Unit And Illuminating
OPERATION SWITCHING ON/OFF THE UNIT is set by RETUNE SHORT (30 sec.) Switch on the unit by pressing any button or RETUNE LONG (90 sec.), the radio start to retune to next same PI (except OPEN button (7) and button (4) station. -
Page 10: Loudness
OPERATION clockwise or counter-clockwise. c) RETUNE L or RETUNE S mode - BEEP 2'nd mode: The initial time of automatic TA search The beep is only generated when or PI search modes is selected. all allowed double key is pressed When PI information is not caught for long (1 sec). -
Page 11: Vacuum Fluorescent Display
OPERATION The reception band will change in the LIQUID CRYSTAL DISPLAY following order: Exhibit current frequency and activated functions on the display (8). FLASHING LED If the front panel does not install in the SELECTING STATION main unit, the LED (12) will be flashing. Press TUNE/RACK button(16) REMOTE SENSOR... -
Page 12: Rds (Radio Data System) Operation
OPERATION PTY MUSIC group PTY SPEECH group PTY off RDS (RADIO DATA SYSTEM) OPERATION - Setting RDS mode According to above 2 allotted group, Press AF/REG button (3) and the preset number is used for PTY release immediately to switch on or selection as follows: off RDS mode. -
Page 13: Cd Operation
OPERATION information is being transmitted The purpose of this key is to reduce or not unwanted EON TA switching, which EON: Enhanced Other Networks EON TA information was received Information from current station and the radio Broadcasting information on PI, switched to that EON linked station, AF, TP, TA, etc, relating to but no information could not be... -
Page 14: Playing All Track In Random
OPERATION PLAYING ALL TRACKS IN RANDOM PLAYING ALL TRACK IN RANDOM Press SHF button (23) to play all Press SHF button (23) to play all tracks on CD in random order. Press tracks on MP3 disc in random order. again to cancel the function. Press again to cancel the function. -
Page 15: Display Information
OPERATION - Press SEL button to confirm entry the currently playing file name is of each characters. displayed (selected). The user can - Press BND /LOU (ENT) select the directory or file in the button to start the title search, directory by TUNE/RACK UP/DOWN buttons. -
Page 16: Wma Operation
OPERATION OPERATION For the unit that can play the Wma disc, the operation is the same with Mp3 operation described above. USB PLAY OPERATION ln the front panel of the unit, there is an USB interface(26). You can connect an Mp3 player or other device with the USB interface through this interface(26). -
Page 17: Disc Notes
OPERATION C. Notes on MP3 files (MP3 Version DISC NOTES Only): A. Notes on discs: 1. The disc must be in the ISO9660 level 1. Attempting to use non-standard 1or level 2 format, or Joliet or Romeo shape discs (e.g. square, start, heart) in the expansion format. -
Page 18: Specification
SPECIFICATION GENERAL Power Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 165 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) 10 dB - Treble (at 10 kHz) 10 dB Maximum Output Power : 4x40 watts Current Drain : 15 Ampere (max.) -
Page 19: Trouble Shooting
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition switch is If the power supply is properly not on.
Need help?
Do you have a question about the CS171 USB and is the answer not in the manual?
Questions and answers