1. Manuals
  2. Brands
  3. Emprex Manuals
  4. Network Storage Server
  5. NSD-100
  6. User manual

Emprex NSD-100 User Manual

Emprex nsd-100 download device: user guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
P2P Download Engine
NSD – 100
User Guide

Advertisement

Table of Contents
loading

Summary of Contents for Emprex NSD-100

  • Page 1 P2P Download Engine NSD – 100 User Guide...

  • Page 3: Table Of Contents

    4. Package Content 5. Hardware Introduction Front View...9 Rear View ...10 6. Installation ...12 6-1 Connect the NSD-100 to ADSL MODEM ...12 6-2 Connect the NSD-100 to HUB ...21 6-3 Connect the NSD-100 to ROUTER...22 6-4 DMZ Setting ...27 6-5 Share mapping...32 7.
  • Page 4 7-2-3 LAN ... 48 7-2-4 Device Setting ... 48 7-2-5 USB... 49 7-2-6 User Folder ... 53 7-2-7 Share Folders... 55 7-2-8 Media ... 55 7-2-9 Tool... 56 8. Q & A...62...

  • Page 5: Attention

    USB HDD with NSD-100 to avoid insufficient electric power effecting the data access. 4. Please do not remove any USB HDD from NSD-100 directly while NSD-100 is on working. Follow the instruction of Charter 7 to avoid any data losing or HDD crash.

  • Page 6: Product Introduction

    2. Product Introduction Thank you for buying this product. NSD-100 is a compact, economical NAS (Network-attached stooge), providing an excellent data storage for personal requirement. With first time setup procedure are simple and user-friendly, besides, benefits are ▪ Computers are not required to be powered on whole time while in process of downloading;...
  • Page 7 Standard USB 1.0/1.1/2.0, IEEE 802.3, IEEE 802.3u Ports 1. 10/100 RJ-45 Ethernet port x1 2. USB 2.0 x2 LAN protocol TCP/IP Protocol Buttons 1. USB eject x2 2. Reset hole x1 Power Input: 100~240V, Output: 5V/2A Memory 1. Flash ROM 8MB 2.

  • Page 8: System Requirements

    Content Please check the following list of content first. If there is anyone missing or flawed, please contact with your seller. 1. NSD-100 Device X 1 2. User Guide X 1 3. Power Adapter (5V/2A) X 1 4. Network cable 10-100 BASE-T X 1...

  • Page 9: Hardware Introduction

    5. Hardware Introduction Front View ① USB LED II (Green) Lighten Green Blinking Green ② USB LED I (Green) Lighten Green Blinking Green USB device I connected to port ⑥ No USB device connects to port ⑥ Data TX/Rx USB device I connected to port ⑤ No USB device connects to port ⑤...

  • Page 10: Rear View

    ③ Reset key Press and hold for 10 seconds to reset all configurations to factory default settings. Cable (10/100 base-T) connected LAN disconnection Data TX/RX Power on and NSD-100 ready System initializing Power on but NSD-100 not ready or faulty...
  • Page 11 “USB II” goes off. Now you could safely remove the USB II device from NSD-100. Attention： In order to use USB HDD with NSD-100, the capacity of external HDD must be more than 10GB and formatted to Linux-HD or FAT32-HD by NSD-100. NSD-100 will recognize the formatted BT-HDD when the HDD connects to USB I or USB II.

  • Page 12: Installation

    NSD-100. 1. Now, if your computer is linking and using under ADSL MODEM, please select the way of chapter 6-1 to install NSD-100 2. If your computer is linking and using under HUB, please select the way of chapter 6-2 to install NSD-100 3.
  • Page 13 HUB (over 2 LAN port), also have a static IP or more dynamic IP address. Following section indicate how to configure on your NSD-100. Second, Connect the LAN port of ADSL modem to NSD-100 and PC. Third, please set up the network with the following steps.
  • Page 14 Step.2 Double click the icon “Local Area Connection” and press right key of your mouse, select “Properties”. Step 3. Select “Internet Protocol (TCP/IP)” select “Properties”...
  • Page 15 NOTE 1. Default IP of NSD-100 is 192.168.16.1 2. Please make sure your PC and NSD-100 in the same LAN. Finally, please set up the NetTool with following steps. Step 5 The bundled program, NetTool is green software. Please copy it to...
  • Page 16 Double click the ICON “NetTool.exe” on the desktop of Windows to start setting wizard. Click “Refresh list” and you will see NSD100 (Serial Number) on the upper of dialogue “Device list”. Step 6. Click “Setup wizard”...
  • Page 17 NOTE Default IP of NSD-100 is 192.168.16.1 Step 7. a. When the “Verify” window pops up, enter the username and password, the user name and password are “admin” & “root”. b. Click “OK.” and window “Wizard” will automatically appear. Step 8.
  • Page 18 Step 9. a. Select “Static IP” for Protocol b. Enter IP address 192.168.16.1, subnet mask 255.255.255.0, NOTE If you select Static IP, please make sure your PC and NSD-100 are in the same LAN.
  • Page 19 Step 10. Due to the connection is not with NAT Router, please ignore the message and click “Finished”. Step 11. Click “Access via Web” to enter WEB administration.
  • Page 20 WEB Administration Step 12 a. Click “administration” on the left and will pop up windows, enter Username and password, the username and password are “admin” & root. b. Select “PPPoE” for protocol, enter your ADSL username and password which is provide by the internet Services Provider (ISP) c.

  • Page 21: Connect The Nsd-100 To Hub

    (Please skip to chapter 7-2-1 for operate of BT setting) 6-2 Connect the NSD-100 to HUB Confirm it belong to the connection way is dialing (PPPoE, Point-to-Point Protocol over Ethernet) or static IP that the telecommunication company offers service of giving to you first.

  • Page 22: Connect The Nsd-100 To Router

    6-3 Connect the NSD-100 to ROUTER Confirm it belong to the connection way is dialing (PPPoE, Point-to-Point Protocol over Ethernet) or static IP that the telecommunication company offers service of giving to you first. DHCP mode Step 1. Click NetTool.exe ICON desktop open.
  • Page 23 Step 2. Click “Setup Wizard” Step 3. Enter the default setting Name: admin; Password: root and click “OK.”...
  • Page 24 Step 4. Click “Next” Step 5. Select “DHCP” for Protocol NOTE: If you select “DHCP” protocol, please make sure to enable DHCP function in your Router.
  • Page 25 Step 6. Click “Next” Step 7. There will be a screen show “Due to the router’s firewall will slow down the BT speed, please set the DMZ of router as xxx.xxx.xx.x ” Please remember this IP Address and click “Finished.”...
  • Page 26 NSD-100 will link to your Router automatically, please key in the router’s account and password (please refer to Router’s manual) for DMZ setting. (Setting manner is in chapter 6-4) Step 8. After finishing the DMZ setting, please click “Access via Web” to enter...

  • Page 27: Dmz Setting

    Some Routers provide DMZ function. If your NSD-100 is located behind the NAT router, you can forward LAN IP address specified by DMZ to NSD-100. When this setting is done, all ports from WAN to LAN will be forwarded to NSD-100.
  • Page 28 Step 1 When NetTool accesses your NAT Router, a dialogue will ask for user name and password to login. In general the factory default setting are “admin” and “admin,” please refer to your user’s manual of NAT router for detail.) Step 2 After logging in, you will see the home page of NAT Router.
  • Page 29 Step 3 Set the IP Address of DMZ as same as the IP Address of NSD-100 and click “Add” to continue. IP of NSD-100 You will see the IP Address of NSD-100 in the dialogue after setting successfully. You may also open your PC’s web browser and enter your static IP Address of NAT Router.
  • Page 30 Port Forwarding If your Router does not have DMZ function, you can select Port Forwarding function too, it has function of accelerating BT download speed too (the port range that BT downloads is downloaded at random by 10000~65535). Here is an example regarding how to set Port Forwarding with commercial NAT router.
  • Page 31 Click “fictitious server” in NAT Router’s setting page. 1. Enter a port value which is not used in “WAN port” 2. Enter the IP Address of NSD-100 in " server IP address ", 3. Click “Apply.” 4. Enter the “ Router IP address：WAN port value” on browser.

  • Page 32: Share Mapping

    6-5 Share mapping If user want to create a shortcut in order to check some folders of NSD-100 HDD. You could use “Share Mapping” function of software NetTool. 1. Click “Share mapping”...
  • Page 33 2. Enter the default username and password (Default setting Name = admin, Password = root) and then click “OK”. 3. Enter the user name and password on left up side of the page. 4. Select the folder and drive letter you want to build for the network drive and click”Map.”...
  • Page 34 NOTE: The username, password and properties of share folder for map remote to local drive are the same as those were configured in following page 7-2-5. To get supervisor authority to manage, you may enter administrator name and password, the username and password “admin”...
  • Page 35 6. You can see network disk Z in following page Confirm if the LAN drive setting is the same as NetTool’s.
  • Page 36 If the LAN drive disappear each time restart the computer, you may try the following setting to exist the drive. Click “My Computer” → “Tool” → “Map Network Drive”...
  • Page 37 After setting the “drive” and “folder”, please check the option “Reconnect at logon.” Click “Unmap” to remove LAN drive.

  • Page 38: Web Administration

    7. WEB Administration NSD-100’s administration page supports three languages interface- English, Traditional Chinese, Simple Chinese for users. 7-1 Home page Users may select language and check the information of NSD-100 and connecting USB device. NOTE: Default IP of NSD-100: http://192.168.16.1...

  • Page 39: Administration

    It also supplies some tools to help users. 7-2-1 BitTorrent First, please connect USB-HD to any USB PORT of NSD-100. The USB-HD needs to format via NSD-100. Next, you could access BT file. (Please refer to chapter 7-2-9-2 Hard Disk Format)
  • Page 40 Please click " Bit Torrent" from MENU on the left. 7-2-1-1 BitTorrent Global setting 1. Place the torrent file in folder “Public” or other folder. 2. You may set the download/upload speed and job procedure.
  • Page 41 4 hours, NSD-100 will jump to process next job. That means if there is no one share and upload the file to you, NSD-100 will follow the setting to stop job polling. This setting is important to avoid resource occupation and then delay other jobs.
  • Page 42 Start next uncompleted job automatically: NSD-100 will re-start uncompleted job automatically if there is an uncompleted job and NSD-100 confirms to upload setting of item b. 7-2-1-2 Create New Job 1. Put the seed file into the folder of computer 2.
  • Page 43 The new job will be listed in BitTorrent table. Click “Start” will launch to download file...
  • Page 44 Click “Details” will display the detailed progress of download 7-2-1-3 Refresh Click “Refresh” will show latest status of the download file.

  • Page 45: Ftp Server

    OS in “client PC’s Language.” *How to Use FTP 1. Should have FTP software first (ex. CoreFTP) The following picture set FTP port 21 for NSD-100, please set FTP software access port to 21, too.
  • Page 46 2. Confirm that user name and password is the same as NSD-100 setting.
  • Page 47 3. Enter the IP Address of NSD-100 and click “Connect.”...

  • Page 48: Lan

    7-2-3 LAN DHCP Obtain IP address automatically via DHCP. If your network configuration support DHCP, NSD-100 will use DHCP protocol to retrieve the IP address and related information automatically. Static IP To use fixed IP for network connection, enter fixed IP address, subnet and default gateway, primary DNS and secondary DNS.

  • Page 49: Usb

    Enter the name of NSD-100, The device name can be 16 characters long at maximum. Date/time Set the date, time zone according to your location. NTP/NTP server NTP Server is an internet time server that enables NSD-100 to show the same time as your computer. You may check NTP -“Enable” to synchronize the system time.
  • Page 50 (Please refer to 7-2-9-2 format hard disk for more detail) 7-2-5-2 USB Printer You could connect USB printer to any USB port on NSD-100 as printer’s server. Please install the newest factory’s driver. Do not use the built-in similar driver.
  • Page 51 Step 1: Click “USB” from MENU on the left. Step 2: Select “USB Storage Devices” → “Share Name” → “NSD-100 HD” and click twice. Step 3: It will show the connected printer’s name on your computer. Please click the printer’s icon twice.
  • Page 52 Step 4: There will be a pop-up window asking the installation program. Step 5: After you find the printer’s driver, please select “Have Disk” and click “OK.”...

  • Page 53: User Folder

    NOTE 1. If each computer needs to share printer under the same LAN, each computer must install driver first. 2. If there are more than two printers, please set NSD-100 as default value. 7-2-6 User Folder You may add new user, change password and delete user.
  • Page 54 Add a new user ： Set the user name, password and share properties whether sharing folder to other user or not. Modify the password Delete a user 1. Leave user’s share folder for administrator (read/write) Leave user’s folder in sub directory of admin. 2.

  • Page 55: Share Folders

    “not accessible to other users”, “read-only to other users” or “read/write to other users”. 7-2-8 Media Once enable UPNP AV server function and assign AV sharing folder, Nero Show-Time or other software that supports UPNP AV could automatically find and play the video and audio from NSD-100.

  • Page 56: Tool

    Linux-HD or FAT32-HD by NSD-100. Note1: Windows system cannot recognize Linux-HD format directly without through NSD-100. Note2: Windows system can recognize FAT32-HD format directly without through NSD-100 but the maximum file size is 4GB due to FAT32 limitation.
  • Page 57 7-2-9-3 Firmware Upgrade User may check new firmware at the website http://www.emprex.com. Firmware location: Support/Download/Multimedia storage/P2P download You may download the new firmware to PC. After completed download, click “FW upgrade” → “Browse” for firmware located directory and click “Start upgrade”. “Bee” twice shows the upgrade is completed...
  • Page 58 Save to the desired directory Click “Restore” to restore previous setting. ” Select “Browse” to find the previous directory and click “Open.
  • Page 59 7-2-9-5 Factory Default Users may click “Restore Default Settings” key to restore factory default setting, or press the “Reset” button on the rear panel of NSD-100 for 10 seconds.
  • Page 60 User may change the user name and password here. (Factory default value Name = admin, Password = root) 7-2-9-7 System Log NSD-100 can store recent event logs for analyzing system problem. 7-2-9-8 E-Mail Sending Once the following events happened, NSD-100 will send e-mail to inform user 1.
  • Page 61 6. Format USB HDD completely...

  • Page 62: Q & A

    NAT router. 2. Q: why does the USB LED still lighten after I removed USB device？ A: You just need to restart NSD-100 since USB device was removed irregularly. Please follow chapter 5 to remove your SUB device. 3. Q: Why can’t my printer print more than two pages of document? A: Please confirm if the printer has installed original factory driver and HD is well connected.
  • Page 63 8. Q: How do I use NSD-100’s FTP function？ A: If your NSD-100 works in static IP, you may enter the static IP Address, user name and password in FTP software for connecting NSD-100 as FTP server; If your NSD-100 works in...
  • Page 64 A: This is language-decoding problem of web browser. It is recommended to use professional FTP software, like CoreFTP to set both languages to “Union Code” for NSD-100 and FTP software. 13. Q: If the network drive disappears each time while reboot the computer, you may try the following setting to keep the connection of network drive after rebooting.
  • Page 65 2. Click “My Computer” → “Tool” → “Map Network Drive”...
  • Page 66 A: Some users stopped sharing file lead to torrent decrease or error. The error may slow down BT download rate or download error. If your NSD-100 is located behind route, you may refer to 6-4 DMZ setting in details, and the BT download rate should be enhanced.
  • Page 68 3100553880 Version 1.0 July 2007...

Table of Contents