Table of Contents
Advertisement
INSTALLATION
d) Cut the 2 ft. (.6m) section of rigid pipe
to length. Ensure that the pipe length
when cut will seat onto both the starter
elbow. Crimped
collar and the 90
o
section of rigid pipe seats into the
90
elbow. Only cut the uncrimped
o
side of pipe.
Dismantle all pipe sections including flue
terminal.
3) Attach the 4" (102mm) dia. flex liner to the
flue terminal ensuring that the flex overlaps
the collar of the flue terminal by a minimum
of 1-3/8"(35mm). Use Mill-Pac to seal and
secure with 3 of the #8 x 1/2" (13mm) screws
(stainless steel).
4) Attach the 2 ft. (.6m)pipe section to the flue
terminal using Mill-Pac and/or high tempera-
ture silicone and attach with 3 of the #8 x
1/2" (13mm) screws (stainless steel).
Hint: Apply the
sealant (Mill-
Pac and/or high
t e m p e r a t u r e
silicone) to the
outer pipe be-
fore connecting
the inner pipe.
Note: The pipe seam should be facing
down.
O u ts
Note: To make the installa-
Furring
tion more aestheti-
cally pleasing, we
recommend framing
out a square that the
cap can be mounted
Fourrures en bois
on.
Note: If installing termination on a siding
covered wall, a vinyl siding standoff or
furring strips must be used to ensure
that the termination is not recessed
into the siding. For vinyl siding stand-
off installation refer to the Dura-Flue
Termination instructions.
5) Slide the partially connected pipe and flue
terminal assembly through the wall (from
the exterior into the interior) and secure the
cap to the exterior wall with 4 of the supplied
screws (#8 x 1-1/2" (38mm) drill point, stain-
less steel).
Note: The four screws provided for the
flue cap should be replaced with ap-
propriate fasteners for stucco, brick,
concrete, or other types of sidings.
12
6) A bead of non-hardening mastic should be
run around both the termination and vinyl
siding standoff to prevent water from entering
and to make a tight seal between the cap
a ll
id e W
Furstrp.eps
and the standoff.
see also c34020a.eps
Strips
7) Stretch the 4" (102mm) dia. flex liner out
fully and get a trial fit of the liner onto the
4" (102mm) dia. starter collar.
ri e u r
e x té
M u r
furstrpf.eps
french
8) Cut the 4" (102mm) dia. flex liner to the
desired size.
Hint: leave an extra 12" to 16" (305mm to
406mm) of length, this will make the final
assembly easier to work with.
9) Secure the 4" (102mm) dia. flex liner to the 4"
(102mm) adapter with Mill-Pac and 3 of the
#8 x 1/2" (13mm) screws (stainless steel).
10) Slide the Decorative Wall Cover over the
pipe sections.
11) Slide the 90
2 ft. (.6m) pipe section (crimp end up) over
the 4" dia. flex liner.
12) Slide the trim collar over the pipe section to
cover the joint.
13) Install the spring spacers onto the pipe
sections.
14) Secure the 4" (102mm) dia. flex liner with
adapter onto the stove collar. Put a bead of
elbow (crimp end up) and the
o
Regency FG39-1 FireGenie Freestanding Gas Stove
#8 x ½" (13mm) Self Tapping, Stainless Steel
#8 x ½"
(13mm)
Self Tapping, Black
#8 x 1½" (38mm) Drill Point, Stainless Steel
Mill-Pac around the appliance adapter and
secure with 3 screws (#8 x 1/2" / 13mm,
stainless steel).
15) Attach the pipe section onto the starter
collar by sealing with Mill-Pac and/or high
temperature silicone and securing with 3 of
the #8 x 1/2" (13mm) (black) screws. Pipe
seams should be facing the wall.
16) Attach the 90
elbow onto the pipe section by
o
sealing with Mill-Pac and/or high tempera-
ture silicone and securing with 3 of the #8
x 1/2" (13mm) screws (black).
17) Slide the 2 ft. (.6m) pipe section onto the 90
elbow. The flex may have to be compressed
back in order for the pipe to properly mate
to the elbow. Seal with Mill-Pac and/or high
temperature silicone and secure with 3 of
the #8 x 1/2" (13mm) screws (black). Pipe
seams facing down.
18) Install the trim collar over the starter collar
and secure with a #8 x 1/2" (13mm) screw
(black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
NOTE: All inner joints must be sealed with
Mill-Pac.
All outer joints may be sealed with
high temperature silicone.
o
Advertisement
Table of Contents
