Pioneer HTP-075 Operating Instructions Manual page 26

4
4
Setting/What it does
LFE ATT (LFE Attenuate)
Some Dolby Digital and DTS audio sources
include ultra-low bass tones. Set the LFE
attenuator as necessary to prevent the ultra-
low bass tones from distorting the sound from
the speakers.
The LFE is not limited when set to 0 dB,
which is the recommended value. When set
to –15 dB, the LFE is limited by the
respective degree. When OFF is selected, no
sound is output from the LFE channel.
f
SACD G. (SACD Gain)
Brings out detail in SACDs by maximizing the
dynamic range (during digital processing).
HDMI (HDMI Audio)
Specifies the routing of the HDMI audio
signal out of this receiver (AMP) or through to
a TV (THRU). When THRU is selected, no
sound is output from this receiver.
g
A.DLY (Auto Delay)
This feature automatically corrects the audio-to-
video delay between components connected
with an HDMI cable. The audio delay time is set
depending on the operational status of the
display connected with an HDMI cable. The
video delay time is automatically adjusted
according to the audio delay time.
h
C.WIDTH (Center Width)
(Applicable only when using a center speaker)
Spreads the center channel between the front right
and left speakers, making it sound wider (higher
settings) or narrower (lower settings).
Making the C.WIDTH setting "7" may cause no
sound to be output from the center channel.
h
DIMEN. (Dimension)
Adjusts the surround sound balance from
front to back, making the sound more distant
(minus settings), or more forward (positive
settings).
Option(s) Setting/What it does
0 (0 dB)
PNRM. (Panorama)
Extends the front stereo image to include
5 (–5 dB)
surround speakers for a 'wraparound' effect.
10 (–10 dB)
C.IMG (Center Image)
15 (–15 dB)
(Applicable only when using a center speaker)
20 (–20 dB)
Adjust the center image to create a wider
stereo effect with vocals. Adjust the effect
** (OFF)
from 0 (all center channel sent to front right
and left speakers) to 10 (center channel sent
to the center speaker only).
0 (0 dB)
a. You can change the Sound Retriever feature at any time by
using
S.RETRIEVER
+6 (+6 dB)
b. The default setting when the USB input is selected is ON.
c. This setting works only with dual mono encoded Dolby Digital
AMP
and DTS soundtracks.
THRU
d. This is not displayed by default. You need to change some
settings on this unit to display the menu. (see
Fixed PCM Setting menu on page
e. The initial set AUTO is only available for Dolby TrueHD signals.
OFF
Select MAX or MID for signals other than Dolby TrueHD.
f. You shouldn't have any problems using this with most SACD
ON
discs, but if the sound distorts, it is best to switch the gain
setting back to 0 dB.
g. This feature is only available when the connected display
supports the automatic audio/video synchronizing capability
('lip-sync') for HDMI. If you find the automatically set delay
time unsuitable, set A.DLY to OFF and adjust the delay time
0 to 7 manually. For more details about the lip-sync feature of your
display, contact the manufacturer directly.
Default: 3
h. Only available with 2-channel sources in DOLBY PLII MUSIC mode.
i. Only when listening to 2-channel sources in NEO:6 CINEMA
and NEO:6 MUSIC mode.
–3 to +3
Default: 0
Option(s)
OFF
h
ON
0 to 10
i
Default: 3
(NEO:6 MUSIC),
10 (NEO:6
CINEMA)
button.
Displaying the
27).
26
Listening to your system
2
4
34