Dimension Drawings; Block Diagrams - Electro-Voice ZX Series ZX1i Technical Specifications

Dimension Drawings:

Top View
Front View

Block Diagrams:

ZX1i (Non-Transformer) and ZX1i (With Transformer) in 8 Ohm Mode
This ZX1i Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the
ZX1 Users Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an
authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.
ZX1i Part Numbers
• 301851-001 - ZX1i-90, 90° x 50° Horn, Black Finish
• 301851-002 - ZX1i-90W, 90° x 50° Horn, White Finish
• 301851-003 - ZX1i-100, 100° x 100° Horn, Black Finish
• 301851-004 - ZX1i-100W, 100° x 100° Horn, White Finish
• 301852-001 - ZX1i-100T, 100° x 100° Horn, Black Finish, Transformer
• 301852-002 - ZX1i-100TW, 100° x 100° Horn, White Finish, Transformer
• 301852-003 - ZX1i-90T, 90° x 50° Horn, Black Finish, Transformer
• 301852-004 - ZX1i-90TW, 90° x 50° Horn, White Finish, Transformer
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Telex Communications, Inc. 05/2006
Part Number 38110-470 Rev. C
Architectural and Engineering Specs:
The loudspeaker shall be a two-way system consisting of one 8"" (102mm) low-
frequency transducer, a 1.25" titanium diaphragm true high frequency compression
driver with rotatable horn and a frequency dividing network installed in a vented
enclosure. The network shall include a full range passive limiter for total system
protection. The high frequency compression transducer shall drive a horn to evenly
cover a pattern of either 90° by 50° or 100° by 100°. The horn shall be rotatable to
allow for horizontal or vertical mounting of the cabinet. The enclosure shall be molded
of high impact polystyrene.
The finish shall be a paintable black or white. The grille shall be zinc plated, powder
coated for corrosion resistance, and equipped with both hydrophobic cloth and acoustic
foam. The loudspeaker position shall be adjustable over a range of 100° horizontally
and 45° vertically.
The support bracket shall be low profile and integral with the enclosure. The bracket
shall allow for a quick snap fit mounting of the speaker enclosure for placement
before securing. The speaker terminals shall include a 4 pin removable phoenix style
connector to allow for signal pass through. The system shall be weather resistant to
MIL Spec 810 and IEC 529 test conditions.
The loudspeaker shall be available with a 100w transformer for 70 or 100v operation.
The speaker shall have ASC
There shall also be an 8 ohm bypass position on the wattage selector switch to enable
8 ohm operation from these models.
The loudspeaker system shall meet the following performance criteria: Power handling,
200-Watts long term program using IEC268-5 shaped pink noise; Frequency response,
48 Hz – 20 kHz (-10 dB from rated sensitivity); Pressure sensitivity, 94 dB at one
watt, 60 Hz – 20 kHz at one meter; Impedance, 8 ohms nominal, 6 ohms minimum.
The enclosure shall be 17.75" (451mm) high, 11.12" (282mm) wide, 10.35" (263mm)
deep. Net weight shall be 18.5 lbs (8.4 kg) for non-transformer versions and 23.0 lbs
(10.4 kg) for transformer versions.
Right View
CAUTION
Performance Match
• D170180
• D170261
Accessories
• 301918-001
• 301955-001
U.S.A. and Canada only. For customer orders, contact Customer Service at:
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
Other International locations. For customer orders, contact Customer Service at:
For warranty repair or service information, contact the Service Repair department at:
TM for protection against transformer saturation overload.
ZX1i (With Transformer)
CPS2T, 120V Power Amplifier, 2 x 600W
CPS2.8, 120V Power Amplifier, 2 x 800W
AB-ZE, Array Bracket Kit for 2 or 4 ZX1i or
EVID Systems, Black
TC-ZX1i, Terminal Cover with Gland Nut
+ 49 9421-706 0 Fax: + 49 9421-706 265
+ 1 952 884-4051 Fax: + 1 952 736-4212
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
800/392-3497 Fax: 800/955-6831
800/685-2606