1. Manuals
  2. Brands
  3. British Fires Manuals
  4. Indoor Fireplace
  5. NEW FOREST 2400
  6. Installation & user's instructions

British Fires NEW FOREST 2400 Installation & User's Instructions

Hide thumbs Also See for NEW FOREST 2400:
Table of Contents

Advertisement

Quick Links

//
INSTALLATION & USER INSTRUCTIONS
NEW FOREST 2400 ELECTRIC FIRE
Single Glass Pane & Rotisserie

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NEW FOREST 2400 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for British Fires NEW FOREST 2400

Summary of Contents for British Fires NEW FOREST 2400

  • Page 1 INSTALLATION & USER INSTRUCTIONS NEW FOREST 2400 ELECTRIC FIRE Single Glass Pane & Rotisserie...

  • Page 4: Important Notes

    Appliance Data for the New Forest 2400 that is regularly switched on and off by the utility. DO NOT switch the appliances on until it is properly installed as...
  • Page 5 Appliance Data for the New Forest 2400 that is regularly switched on and off by the utility. DO NOT switch the appliances on until it is properly installed as...

  • Page 6: Installation Requirements

    2.0 INSTALLATION REQUIREMENTS 3.0 APPLIANCE DATA New Forest 2400 These electric fires are fitted with LED’s (Light Individual Appliance Tech Specs Emitting Diode) in place of conventional bulbs. LED’s Weight (kg) 50kg These appliances are supplied with a pre-wired three pin generate the same light levels as conventional bulbs, plug (13 Amp fuse rated) and 1.8 metres of electrical...
  • Page 7 2.0 INSTALLATION REQUIREMENTS 3.0 APPLIANCE DATA New Forest 2400 These electric fires are fitted with LED’s (Light Individual Appliance Tech Specs Emitting Diode) in place of conventional bulbs. LED’s Weight (kg) 50kg These appliances are supplied with a pre-wired three pin generate the same light levels as conventional bulbs, plug (13 Amp fuse rated) and 1.8 metres of electrical...

  • Page 8: Component Checklist

    These appliances are heavy. Always seek assistance whilst Please read completely through the instructions and verify that unpacking and/or during installation. Please read all the all listed parts are present before assembly. instructions before continuing to unpack or install appliance. © 2021 British Fires CAUTION:...
  • Page 9 These appliances are heavy. Always seek assistance whilst Please read completely through the instructions and verify that unpacking and/or during installation. Please read all the all listed parts are present before assembly. instructions before continuing to unpack or install appliance. © 2021 British Fires CAUTION:...
  • Page 10 - c o m b u s t i b l e material, such as calcium silicate/ Drawings are not to scale Drawings are not to scale Drawings are not to scale fireboard. © 2021 British Fires...
  • Page 11 - c o m b u s t i b l e material, such as calcium silicate/ Drawings are not to scale Drawings are not to scale Drawings are not to scale fireboard. © 2021 British Fires...
  • Page 12 Tap the 8x wall anchors into the pre--drilled holes with a hammer until Small trim appliances. they are flush with the wall. Secure the mounting bracket to the wall by using all 8 wall-fixing screws. Carefully, install the appliance back onto the wall bracket. © 2021 British Fires...
  • Page 13 Tap the 8x wall anchors into the pre--drilled holes with a hammer until Small trim appliances. they are flush with the wall. Secure the mounting bracket to the wall by using all 8 wall-fixing screws. Carefully, install the appliance back onto the wall bracket. © 2021 British Fires...
  • Page 14 9.0 PREPARING THE APPLIANCES Line the two appliances next to each other with Remove the frosted fuel bed and black trim that the bed the opened ended sides pushed up together. Using sits in from both fires by removing the 8 silver screws a spirit level ensure that both appliances are from each appliance with a cross-headed screw driver.
  • Page 15 9.0 PREPARING THE APPLIANCES Line the two appliances next to each other with Remove the frosted fuel bed and black trim that the bed the opened ended sides pushed up together. Using sits in from both fires by removing the 8 silver screws a spirit level ensure that both appliances are from each appliance with a cross-headed screw driver.
  • Page 16 DO NOT REMOVE THE SCREW FROM THE FAR RIGHT OF THE FLAME EFFECT! On the left hand side appliance only, removed the 4x screws holding the LED deflector Remove the infill flame cutout panel from the right hand side appliance. © 2021 British Fires...
  • Page 17 DO NOT REMOVE THE SCREW FROM THE FAR RIGHT OF THE FLAME EFFECT! On the left hand side appliance only, removed the 4x screws holding the LED deflector Remove the infill flame cutout panel from the right hand side appliance. © 2021 British Fires...
  • Page 18 1.50mm allen key, connecting the two together. turn the rotisserie 180° and tighten the other grub screw. Remove the transit screw from the end of the shaft coupler with a cross headed screw driver. © 2021 British Fires...
  • Page 19 1.50mm allen key, connecting the two together. turn the rotisserie 180° and tighten the other grub screw. Remove the transit screw from the end of the shaft coupler with a cross headed screw driver. © 2021 British Fires...
  • Page 20 Ensure the glass is supported at all times. Screw the 4x clamps back into the top, rear of Screw the top clamps from each side back into the appliance, securing the rear glass into position. position, holding the side glass in place. © 2021 British Fires...
  • Page 21 Ensure the glass is supported at all times. Screw the 4x clamps back into the top, rear of Screw the top clamps from each side back into the appliance, securing the rear glass into position. position, holding the side glass in place. © 2021 British Fires...
  • Page 22 Place the trim plate in between the two frosted fuel beds. Double sided tape can be used if required (not supplied). © 2021 British Fires...
  • Page 23 Place the trim plate in between the two frosted fuel beds. Double sided tape can be used if required (not supplied). © 2021 British Fires...
  • Page 24 10.0 FOREST VIEW FUEL BED LAYOUT Forest View Taking a small account of the small crystals, scatter randomly over the Use the slate pieces and place these randomly on the bed as shown in frosted base as shown above. image 4, above.
  • Page 25 10.0 FOREST VIEW FUEL BED LAYOUT Forest View Taking a small account of the small crystals, scatter randomly over the Use the slate pieces and place these randomly on the bed as shown in frosted base as shown above. image 4, above.
  • Page 26 10.1 SLATE VIEW FUEL BED LAYOUT Slate View Evenly scatter the small crystals over the frosted base as shown in image 1, left. The crystals should be spread out across the whole base and form a layer covering the whole area. Take the two types of the slate effect pieces and spread these evenly throughout, on top of the bed of crystals.
  • Page 27 10.1 SLATE VIEW FUEL BED LAYOUT Slate View Evenly scatter the small crystals over the frosted base as shown in image 1, left. The crystals should be spread out across the whole base and form a layer covering the whole area. Take the two types of the slate effect pieces and spread these evenly throughout, on top of the bed of crystals.
  • Page 28 10.2 DIAMOND LIGHT VIEW FUEL BED LAYOUT Three Diamond Light colour settings Diamond light View Evenly scatter the small crystals over the frosted base as shown in image 1, left. The crystals should be spread out across the whole base and form a layer covering the whole area.
  • Page 29 10.2 DIAMOND LIGHT VIEW FUEL BED LAYOUT Three Diamond Light colour settings Diamond light View Evenly scatter the small crystals over the frosted base as shown in image 1, left. The crystals should be spread out across the whole base and form a layer covering the whole area.

  • Page 30: Pairing The Remote Control

    Press to enter the time and week 74°F, 75°F, 76°F, 77°F, 78°F, 79°F, 80°F, timer settings. 81°F, 82°F, ON, 62°F (Cycle) * Press and hold the heater button for 3 seconds can transfer from °C to °F. ©2021 British Fires...
  • Page 31 Press to enter the time and week 74°F, 75°F, 76°F, 77°F, 78°F, 79°F, 80°F, timer settings. 81°F, 82°F, ON, 62°F (Cycle) * Press and hold the heater button for 3 seconds can transfer from °C to °F. ©2021 British Fires...

  • Page 32: Operating The Appliance

    “00:00” status and you won’t be able to set the week timer function. ATTENTION: With the remote paired to both fires correctly the same operation setting will apply to both fires. © 2021 British Fires...
  • Page 33 “00:00” status and you won’t be able to set the week timer function. ATTENTION: With the remote paired to both fires correctly the same operation setting will apply to both fires. © 2021 British Fires...

  • Page 34: Safety Cut-Out System

    Always disconnect each appliance from the mains supply outlet option and enter the current socket before undertaking any cleaning or maintenance! Press the “Heater” button to setting of the option, the timer © 2021 British Fires...
  • Page 35 Always disconnect each appliance from the mains supply outlet option and enter the current socket before undertaking any cleaning or maintenance! Press the “Heater” button to setting of the option, the timer © 2021 British Fires...

  • Page 36: Troubleshooting Guide

    Excluding fuses, use only g e n u i n e m a n u f a c t u r e r s s p a r e p a r t s available from your supplier. © 2021 British Fires...
  • Page 37 Excluding fuses, use only g e n u i n e m a n u f a c t u r e r s s p a r e p a r t s available from your supplier. © 2021 British Fires...

  • Page 38: Appliance Dimensions

    FREE 3-YEAR GUARANTEE WITH REGISTRATION authorised or carried out the repair or replacement. At British Fires we pride ourselves on quality and performance, so much We will not accept or reimburse the costs of any third-party who so that each of our appliances is eligible for a three-year guarantee undertakes any work carried on the appliance or fits parts, unless we when purchased from an authorised dealer.
  • Page 39 FREE 3-YEAR GUARANTEE WITH REGISTRATION authorised or carried out the repair or replacement. At British Fires we pride ourselves on quality and performance, so much We will not accept or reimburse the costs of any third-party who so that each of our appliances is eligible for a three-year guarantee undertakes any work carried on the appliance or fits parts, unless we when purchased from an authorised dealer.
  • Page 40 Christchurch, Dorset New Forest 2400 EU 19215407.8 the text, images and layout of this booklet is owned by British Fires. You are BH23 2BT Electric Fire ( EF40-48A ) not permitted to copy or adapt any of the content without the prior written...

Table of Contents